2016 AUDI Q5 key

..... N
co ~ CX)
..... I.Cl U"I
..... I.Cl .....
Convenience opening/closing
The windows and the Panoramic sliding sunroof*
can be opened and closed with the mechanical
key or the emergency key .
Fig . 41 Key turns for opening and closing
Convenience opening feature
• Use the emergency key or pu ll the mechanical
key out of the master key
c::> page 3 7.
18 9 a::
"' a,
• Insert the key into the lock of the driver's door.
• Turn the key to position
c::> fig. 41 ® until all
the windows have reached the desired position
and the Panoramic sliding sunroof" is tilted.
Convenience closing feature
• Use the emergency key or pu ll the mechanical
key out of the master key
c::> page 3 7.
• Turn the key in the lock of the driver's door to
the lock position @ until the w indows and the
Panoramic sliding sunroof" are closed
c::> A_ .
When you open or close the Panoramic sliding
sunroof*, the power sunshade will also open or
close.
A WARNING
- Never close the windows and the Panoramic
sliding sunroof* inattentive ly and without
checking -there is risk of injury.
- You must always watch when the w indows
are be ing raised so that no one can be trap­
ped.
If you release the key, the closing ac­
tion is immediately canceled.
- Always read and heed WARNING
c::> & in
General description on page 39 .
Open ing and closing
Correcting window regulator malfunction
After disconnecting the vehicle battery, the one­
touch up and down feature must be activated
again .
"' Pull and hold the power window switch until
the window is completely closed .
"' Release the switch .
"' Pull the sw itch again for one second . The auto­
mat ic closing/opening is now reactivated.
Panorama roof
Operation
Applies to veh icles: w it h Pano ra mi c slid ing sunroof
Fig. 42 Section from headliner: Knob for Panoramic s lid in g
su nroof
Tilting
"'The sunroof can be tilted or closed only in
switch position @
c::> fig. 42
"'To tilt it, briefly press the switch c::> fig. 42.
"'To close it, briefly pull the switch c::> A_.
"'To set an intermed iate position, press/pull the
sw itch until the sunroof reaches the desired po­
sition.
Opening
"' To move the sunroof to the position for reduced
w ind no ise, turn the switch to posit ion @ until
res istance can be felt.
• To open the sunroof completely, turn and hold
the switch against the resistance in posit ion @.
• To close the sunroof, turn the switch to posi­
tion @
c::> A..
• Turn the switch to the desired position to select
an intermediate position.
II>
47

Opening and clo sin g
Open ing and clo sing th e sunsh ade
.. To a utomat ically open the sunshade complete­
ly, briefly press the switch @ in the des ired ar­
row direction.
.. To stop the sunshade in an intermediate posi­
tion, press the switch again, or
.. Press and hold the switch in the desired arrow
direction .
.. Release the sw itch when sunshade is at desired
pos ition .
After the ignition is switched off, you can still op­
erate the Panoramic sliding sunroof for about 10 minutes . As soon as the driver's o r passenger's
door is opened, the switch is inoperat ive.
The power sunshade can also be closed when the Panoramic sliding sunroof is open.
A WARNING
Pay careful attention when closing the Panor­
am ic sliding sunroof- otherwise ser ious injury
cou ld result! For this reason, always remove
the ignition key when leaving the vehicle.
(D Note
Always close your Panoramic sl iding sunroof
when leaving yo ur vehicle. Sudden rain can
cause damage to the i nterior equipment of
your veh icle, particularly the electron ic eq uip­
ment.
(j) Tips
I nformat ion regarding convenience opening/
closing
¢page 47.
Emergency closing of the Panoramic slid ing
sunroof
Applies to veh icles: w ith Panoramic sliding sunroof
If the Panoram ic sliding sunroof detects an ob­
ject in its path when it is clos ing , it will open
aga in automatically . In this case, you can close
the roof with the power emergency clos ing func ­
tion .
.. Within five seconds after the sunroof opens au­
tomat ically, pull the switch unt il the roof
closes .
48
Garage door opener
(Homelink)
Description
Applies to vehicles: with garage door opene r (Home Link)
F ig. 43 Ga rage door opene r: examples of us ing w it h d iffer·
ent syste ms
You can act ivate various systems suc h as garage
doors, secur ity systems and home lighting from
inside your vehicle using the garage door opener
(Homelink) . There are three buttons for th is in
the veh icle headliner that can be in used in place
of up to three hand-held transmitters.
To operate systems using the garage door open­
er, the three buttons in the roof headliner must be programmed first .
A WARNING
Make sure no people or objects are in the im­
mediate vi cinity of the equipment when using
or p rogramm ing the ga rage door opener. Peo­
p le can be injured and ob jects can be dam­
aged if they are caught in the equipment.
(D Tips
- For sec urity reasons, we recommend that
yo u clear the prog rammed but tons before
sell ing t he ve hicl e.
- For add itiona l information about Homel ink,
visit www.homelink.com .
- For Declaration of Compliance to United
States FCC and Indust ry Canada regulat ions
~page 283.

..... N
co ~ CX)
..... I.Cl U"I
..... I.Cl .....
-Some exterior lighting functions can be a d­
j u sted
¢page 53 .
-When yo u remove your key from the igni­
tion while the vehicle's lights are t urne d on,
a buzzer sounds as long as the driver's door
i s open.
- In coo l or damp weather, the inside of the
headlights, turn signals and tai l lights can
fog over d ue to the temperature d ifference
between the inside and outs ide. They will
clea r short ly after switch ing them on. This
does not affect the serv ice life of the lig ht­
i ng .
- In the event of a light sensor malfunct ion,
the d river is not ifi ed in t he i nstr ument clus­
te r dis play¢
pag e 32.
Fog lights
Fig . 4 7 Fog ligh t sw itc h
"To turn on the fog lights }O, press button (D
¢ fig. 47.
"T o turn on the rea r fog lights 0$, press but ton
@ .
Fog lights
The s ide marker lights or low beams must be
switche d on. When the fog lights are switc hed
on, the g reen check light at the edge of the
sw itch comes on.
If automat ic driving light control AUTO is activat­
ed, the low beams are sw itched on w hen the fog
lights are tur ned on .
Rear fog lights
Low beams or side marker lights with fog lights
must be t urned on .
Lights and V ision
W hen the rear fog lights are t urned on, the yel ­
l ow check light at the edge of the switch comes
on .
(D Note
The rear fog lig hts should o nly be t urne d on in
accor dance with traffic reg ulation, as the
li g hts are b right for f ollowing traffic .
Adjusting exterior lighting
The functions are selected in the radio or in the
MMI*.
"Sele ct: !CAR ! func tion b utton> Exterior light­
ing .
Or
.. Select:
-,c- A- R~I function button > Car systems *
control b utton > Vehicle settings > Exterior
lighting .
Coming home (Lights when leaving car ),
Leav ing home (Lights when unlock ing car )
The coming home f unction illuminates the area
outside the vehicle when you turn the ignit ion off
and open the d river's doo r. Dependi ng on vehicle
equipment, the function can be sw itched on and
off or the length of time the lights remain on*
c an be ad justed .
The leaving home i llum inates the area outside
t h e ve hicle when you un lock the vehicle . This
funct ion can be switched on and off .
The Com ing home and Leaving home functions
o nly operate when it is dark and the light switch
i s i n the
AUTO pos it ion.
Auto headlights
When the light sw itch is in the AU TO ¢ page 52
pos ition, the switch-on point of the lights can be
changed in the automat ic driving light funct ion.
Daytime running lights
USA models: You can switch the daytime runn ing
li ghts
On and Off .
Canada models:
Th e fu nction canno t be turned
off .
It is a ct ivate d automatica lly ea ch time the ig-
ni tio n i s switched on. ..,
53

Lights and Vision
The mirror returns to its initial position as soon
as reverse gear is disengaged and vehicle speed is
above about 9 mph (15 km/h). The mirror also returns to its initial position if the switch is
moved to the driver's exterior mirror© or the ig­
nition is switched off .
If the position of the mirror surface is changed
on a tilted mirror, this new position will be auto ­
matically assigned to the remote key when the
vehicle is taken out of reverse gear .
(D Note
- Curved mirror surfaces (convex or spheri­ cal*) increase your field of view. Remember
that vehicles or other objects will appear
smaller and farther away than when seen in
a flat mirror. If you use this mirror to esti­
mate distances of following vehicles when
changing lanes, you could estimate incor­ rectly and cause an accident.
- If the mirror housing is moved unintention­
ally (for example, while parking your vehi­
cle), then you must first fold the mirror
electrically. Do not readjust the mirror
housing manually. You could damage the
motor which controls the mirror.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in to reduce the risk of damage to the mirrors.
Never fold power folding exterior mirrors*
by hand . Only fold them in and out using
the power controls.
(D Tips
If there should be a malfunction in the elec­
trical system, you can still adjust the exterior
mirrors by pressing the edge of the mirror.
60
Dimming the mirrors
Fig. 61 Auto ma tic dimmin g rearv iew mirro r*
Manual anti-glare adjustment
.,. Move the small lever (located on the bottom
edge of the mirror) to the rear.
Automatically dimming mirrors* .,. To dim the rearview mirror and both exterior
mirrors*, press the @button. The diode @
turns on . The rearview and exterior mirrors*
dim automatically when light shines on them,
for example from headlights on a vehicle to the rear .
& WARNING
Electrolyte fluid can leak from automatic dim­
ming mirrors if the glass is broken. Electro­
lyte fluid can irritate skin, eyes and respirato­
ry system.
- Repeated or prolonged exposure to electro­
lyte can cause irritation to the respiratory
system, especially among people with asth­
ma or other respiratory conditions. Get
fresh air immediately by leaving the vehicle
or, if that is not possible, open windows and
doors all the way.
- If electrolyte gets into the eyes, flush them
thoroughly with large amounts of clean wa­
ter for at least 15 minutes; medical atten­
tion is recommended .
- If electrolyte contacts skin, flush affected
area with clean water for at least 15 mi­
nutes and then wash affected area with
soap and water; medical attention is recom­
mended. Thoroughly wash affected clothing
and shoes before reuse.

Sea ts and stor age
Front passenger 's seat
Always move the front passenger seat into the
rearmost position.
To avoid contact with the airbag wh ile it is de­
ploying, do not sit any closer to the instrument
panel than necessary and always wear the three­
point safety belt prov ided adjusted correctly. We
recommend that yo u adj ust the passenger's seat
i n t he following ma nner:
.. Move the front passenger seat into the rear­
most position of the fore and aft adjustment
range
c:> .&. in Why is your seat adjustment so
important? on page 63.
.. Bring the back rest up to a n (a lmost) upright
position .
Do not ride with the seat recl ined.
.. Adjust the head restraint so the upper edge is
as even as possible with the top of your head . If
that is not possible, try to adjust the head re­
straint so that it is as close to this position as
poss ible<=>
page 67 .
.. Place your feet on the floor in front of the pas­
senger's seat .
Front seats
Power seat adjustment
Fig. 64 Front seat: Cont rols for seat adju stment
Controls
~ a: a, a:,
@-Adjusting the l umba r suppo rt: p ress the but ­
ton in the correspo nding position
c:> ,& .
@ -Movi ng the seat up/down: p ress the button
up/down. To adjust the front seat c ush ion, press
the front bu tton up/ down. To adjus t the rear sea t
cushion, press the rear b utton up/down
c:> ,& .
64
@ -Moving the seat forward/back: press the but ­
ton forward/back
c:> .&..
©-Adjust ing the b ackrest ang le: press the bu t­
ton forward/back
c:> &. .
@ -Lengthening/sho rteni ng the upper th igh
suppo rt*: lift the handle
c:> &,.
.&, WARNING
- Never adjust the drive r's or front p asseng­
er 's sea t while t he veh icle is moving.
If you
do t his while the vehicle is moving, yo u will
be out of posit ion . Always ad just the driver 's
or front passenger's seat when the vehicle is
not moving .
- Be carefu l when adjusting the seat height.
Check to see that no one is in the way, or se­
rious injury could resu lt!
- Because the seats can be electrically adjust­
ed w ith the ignition off or with the ign ition
key removed, never leave children unattend­
ed in the vehicle. Unsupe rvised use of the
electric seat ad justmen ts may cause serious
in ju ry.
- To reduce the r isk of injury in the case of
sudden b raking or accident, front passen­
ge rs must neve r ride i n a moving ve hicle
w it h the backrest reclined. Safety belts a nd
the airbag system only o ffer maxim um pro­
t ection when the bac krest is upr igh t and the
safety belts are properly positioned on the
body. The mo re the bac krest is reclined, the
greater the risk of personal injury from an
incorrect seating position and improperly
positioned safety belts.
-

..... N
co ~ CX)
..... I.Cl U"I
..... I.Cl .....
Memory function
Memory for driver's seat
Applies to vehicles: with seat memory
The seat adjustment settings for two drivers con
be stored using the memory buttons in the driv­
er's door .
Fig . 65 D ri ver's door : Sea t memory
! co ID
In addition to the setting for the driver's seat ,
the exterior rear view mirror setting can be stor­
ed and recalled through seat memory if the vehi­
cle is proper ly equ ipped .
Storing and recall ing s ettings
With the help of the memory buttons 1 and 2
¢ fig . 65 the settings for two different drivers
can be stored and recalled
¢ page 65.
The cu rrent sett ings are also automatically as ­
signed to the remote contro l key being used
when the vehicle is locked . When the vehicle is
un locked, the settings ass igned to the remote
control key being used are automatica lly reca l­
led.
Turning seat memory on and off
If the IO FFI sw itch is depressed, the seat memory
is inoperat ive . When the Memory fu nction is off,
the LED in the button lights up .
All the sto red se ttings a re retained. We recom­
mend us ing the
IO FF I sw itch and deactivating the
seat memory if the ve hicle is on ly going to be
used
temporarily by a driver whose settings are
not go ing to be stored .
Seats and storag e
Storing and recalling settings
Applies to vehicles: with seat memory
Storing settings
.,. Adj ust the d river's seat.
.,. Adjust the two exterior mirrors.
.,. Press the
!S ET I button. The light in the button
w ill come on.
.,. Now press a memory button
(ill or 121) . If th e
sto ring procedure is correct, a confirmation
tone will sound .
Recalling settings
.,. If the driver's door is open and the ignition is
sw itched off, tap the corresponding memory
button briefly .
.,. If the driver's door is closed or the ignition is
sw itched on, press the approp riate memory
button until the stored position is reached.
Successful storage is confirmed audibly and by
t h e light in the
ISET I button i lluminating
r=> poge 65, fig. 65.
When the vehicle is locked , the current settings
are stored and assigned to the remote control
key . But the settings stored on memory buttons
1 to 2 are not de leted. They can be reca lled at
any time . When the vehicle is
unlocked , the set­
t ings assigned to the remote control key are re­
stored .
If your vehicle is driven by other persons using
your remote control key, you should save your in­
dividua l seat position o n one of the memory but­
tons . You can reca ll you r settings aga in simply
and conveniently by pressing the correspond ing
memo ry button. When the vehicle is loc ked,
t h ese settings are automatically re-ass igned to
t h e remo te contro l key and stored.
_& WARNING
-
- For safety reasons, the seat sett ing can on ly
be recalled when the vehicle is stationa ry -
otherwise yo u risk having an accident .
- In an emergency the recall proced ure can be
cancelled by pressing the
! OF FI switch or by
tapp ing of the memory bu ttons.
65

Sea ts and stor age
Activating remote control key memory
Applies to vehicles: with seat memory
To assign the drive r's seat settings to the remote
con trol key when locking the vehicle, the function
m ust be activated in the radio or M MI*.
• Select:
ICARI funct ion button > Seat adjust­
ment > Dr iver' s se at
> Key mem. profi le > On .
Or
• Se lect:
I CARI funct io n button > Car sy stem s*
contro l button > Vehicle sett ing s > S eats >
Driv er's s eat > Remote control key > On .
@ Tips
If you do not want another driver's settings to
be assigned to the remote control key, switch
off the memory function using the radio or
MMI* or the
j o FF I button ¢ page 65.
Rear seat
General information
Safe transportation of passengers on the rear
seats requires proper safety precautions.
All passengers on the rear seats must be seated
in compliance w ith the safety guidelines ex ­
p lai ned in
¢ page 143 and ¢page 151. The cor­
rect seating positio n is critical for the safety of
fron t
and rear seat passengers a like ¢ page 13 7.
_8. WARNING
- O ccupan ts in the front and rear seats m ust
always be properly res trained.
- Do not let anyone ride in the vehicle withou t
t h e head restraints prov ided. Head re­
straints hel p to reduce injuries.
- Loose items ins ide the passenger compa rt­
ment, can fly forward in a crash or sudden
maneuver and injure occupants. Always
store articles in the luggage compartment
and use the fasten ing eyes, especially when
t h e rear seatbacks have been folded down.
- Read and heed all WARNINGS
¢page 137,
Proper seating positions for passengers in
rear seats.
66
Adjusting seat
The fore-and-a~ adjustment of the seat cushion
and the seatback angle can be adjusted .
Fig. 66 Ad justing seatback angle
F ig . 67 Fore -a n d-aft ad justment
Adjusting seatback angle
• Pull the lever up and push the seatba ck toward
the rea r to the desired position~
fig. 66 . Re­
lease the lever.
• Pull the lever up so that the seatback pivots
forward. Release the lever and push the seat­
back to the rear to retu rn the seatback to the
normal pos ition .
Fore-and-aft adju stment
• Pull the handle up and push the seat forward or
back ¢
fig. 67.
• Release the handle and cont inue to push the
seat until the seat latch engages .
_8. WARNING
- For safety reasons, the seat must only be
ad justed when t he vehicle is stationa ry -
danger of acci dent!

,...,
N
co ~ CX) ,...,
I.Cl U"I ,...,
I.Cl ,...,
- Exercise caution when adjustin g the seat .
Adjusting t he seat w ithout checking or pay­
ing attention can pinch fingers or limbs -
danger of injury!
Head restraints
Front head restraints
F ig. 68 Fro nt seats hea d restrai nts: adjusti ng the he ight
The head restraints on the front seats can be ad­
justed to prov ide safe suppo rt to head and neck
at the optim um height. When optimally adjus t­
ed, the top of t he restraint sho uld be leve l with
the top of the head. If that is not possib le, try to
ad just the head restraint so that it is as close to
this position as possible
<:!) page 137, Proper ad­
justment of head restraints.
.. Grasp the sides of the head res tra int wit h both
hands and slide it upward/downward unt il you
feel it click into p lace
¢ fig. 68.
Refer to ¢ page 13 7, Proper adjustment of head
restraints
for guidelines on how to adjust t he
h e ight of the front head restra ints to suit the oc­
cupant's body size.
A WARNING
- Driv ing without head rest raints or with head
restra ints that are not properly adjusted in­
creases the risk of ser ious or fatal neck in­
jury dramatically.
- Read and heed all WARNINGS
r:.> page 137,
Proper adjustment of head restraints.
Seats and storag e
(D Tips
Correctly adjusted head restraints and safety
belts are an extremely effective combinat ion
of safety features.
Rear head restraints
F ig . 6 9 Rear seat : head restra ints
Fig. 70 Rear seat: o ute r head restraint
If there is a passenger on the rear center seating
pos it ion, slide the center head restra int upward
at least to the next notch
c:> ,A .
Adju sting the head restraints
.. To move the head restrain t up, hold it a t the
sides with both hands and s lide it upward until
you feel it click into p lace.
.. To move the head restraint down , press the
button @ and slide the head restraint down­
ward.
Removing the outer h ead restra ints
.. Fold t he backrest forward c:!) page 69 .
.. Move the head restraint upward as far as it can
go.
.. Press the re lease ®
c:> fig. 70 with the mec han­
ical key
c> page 37 and the button @ c:> fig. 69. IIJJ,
67