2016 AUDI A7 service

M N <( I.J "". rl I.O
"' N I.O rl
Driver information
system
Overview
Fig. 4 Driver information system in th e instr ument cluster
Fig. 5 Display: example of the informat ion line
The driver information system conta ins informa­
tion @ that is disp layed on tabs@¢
fig. 4 . The
following content is possible depending on vehi­
cle equipment:
@
®
Tab C o ntent
1 Veh icle functions:
On-board computer ¢ page 24
Efficiency program* ¢ page 25
Digital speedometer
Cruise control *¢
page 83
Adapt ive cruise control and braking
guard*
¢ page85
Audi active lane assist*¢ page 94
Display darkened Ins
trument s and indi cator ligh ts
@
®
Tab Content
2 Ind icator lights and messages
Warning when a door, the hood or the rear lid is not closed
Service interval display¢
page 26
Speed warning system ¢ page 82
3 Night vision assistant* ¢page 104
4 Audio/video
s Telephone*
6 Navigat ion*
T he second and third tabs are only visible if at
least one indicator light or message is shown or if
that system is switched on.
The status line© is located in the bottom part of
the display ¢
fig. 4. It displays the exterior tem­
perature, time, selector lever position, tripod ­
ometer and odometer .
For some vehicle functions, you can access the
trip information from the temporary memory
¢ page 25 in the line(!)¢ fig. 5.
_& WARNING
-
-Never rely exclusively on the outside tem­
perature display to determine if a road sur­
face is icy or not. Keep in mind that road sur­
faces, especially bridges and overpasses,
could be ice covered and slippery even at an
outside temperatu re above 4 1 °F (+S
0
().
- Always remember, even if the "snowflake"
symbol (ice warning) does not appear in the
d isp lay, black ice cou ld be on the road.
- Always reduce your speed and drive with
specia l care in cold weather cond itions when
the chance of encountering icy road surfaces
i n creases.
(0 Tips
- If the vehicle is stationary, or if you are driv­
ing at a very low speed, the temperature
shown in the display might be slight ly high­
er than the actual outside temperature. This
is caused by the heat being radi ated from
the engine . .,..
23

Instruments and indicato r Lights
Economy tips
In certain situat ions, economy tips appear auto­
matica lly for a short time in the efficiency pro­
gram ~
fig. 10. If yo u follow these economy tips,
you can reduce your vehicle's fuel consumption.
To turn an economy tip off immediately after it
appears, press any button on the multifunction
steering whee l.
(D Tips
-If you e rase the data in the efficiency pro­
gram, the values in the on-board computer
will a lso be reset.
- Once you have turned an economy tip off, it
will on ly appear again after you turn the ig­
nition on again.
- The economy tips are not displayed in every
instance, but rather in intervals over a peri­
od of t ime .
Odometer
Fig . 11 Instrum ent cluste r: o dom eter an d res et butto n
The display of distance driven is shown in m iles
"mi" or kilometers "km". The units of measure ­
ment (kilometers/miles) can be changed in the
Infotainment system.
Upper odometer
The trip odometer shows the distance driven
since it was last reset . It can be used to measure
short distances. The last digit shows distances of
100 meters or 1/10 of a mile .
The trip odometer can be reset to zero by press­
ing the reset button~-
26
Lower odometer
The lower odometer shows the total number o f
kilometers or miles that the vehicle has driven.
Malfunction indicator
If there is a malfunction in the instrument clus­
ter ,
DEF will appear in the tr ip odometer display .
Have the malfunction corrected as soon as poss i­
ble.
Time/date display
Fig. 12 Ins trumen t cl uster : T im e and dat e
The date, time of day and time and date format
can be set in the Infotainment system. Refer to
the Infotainment system operating manual fo r
instructions.
When you open the dr iver's door, the date and
time appear in the instrument cluster display for
30 seconds .
Service interval display
The service interval display detects when your ve­
hicle is due for service .
Fig. 13 Instrume nt cluster d ispl ay: service interv al displ ay
(example)
The service interval display works in two stages: ..,.

M N <( I.J "". rl I.O
"' N I.O rl
-Inspection or oil change reminder: After a cer­
tain distance driven, a message appears in the
instrument cluster display each time the igni­
tion is switched on or off
c> fig. 13. The remain­
ing distance or time is displayed briefly .
-Inspection or oil change due : If your vehicle is
due for an inspection or oil change or both, a
message appears br iefly in the instrument clus­
ter display when switching the ignition on or
off:
Inspection due! or Oil change due! or Oil
change and inspection due! .
Checking service intervals
You can check the remaining distance or time un­
til the next oil change or next inspection n the
Car menu. To do th is, select: the ICAR !function
button
> (Car) * Systems control button > Service
& control
> Servi ce intervals .
Resetting the indicator
Your authorized Audi dealer or authorized Audi
Service Facility will reset the service interval dis­
play after performing service .
If you have changed the oil yourself, you must re­
set the oil change interval.
To reset the indicator, select: the ICARI fu nct ion
button
> (Car)* System control button > Service
& control > Service intervals. Turn the control
knob downward to
Reset oil change interval and
press the control knob.
(D Note
- Only reset the oil change indicator if the o il
was changed.
- Fo llowing the service intervals is critical to
maintain ing the service life and value of
your vehicle, especially the engine. Even if
the mileage on the vehicle is low, do not ex­
ceed the time for the next service.
- Calculating the time to the next oil change
i s interrupted when the vehicle battery is
disconnected. If the vehicle is not driven for
a long period of time, check the mainte­
nance schedule so that you can follow the
maintenance interva ls.
Instruments and indicator lights
Head-up display
Applies to vehicles: wit h Head-up disp lay
Fig. 14 Examp le : Indicato rs i n th e Head -up dis play
Fig . 15 Instrument panel: head-up display knob
The Head-up display projects certain warnings or
selected information from the assistance sys ­
tems* or navigation* on the windsh ield . T he dis­
play appears w ith in the dr iver's field of vision.
Switching on/off
... To switch the head-up d isplay on or off, press
the knob~
c> fig. 15.
Adjusting the height
The height of the display can be adjusted to the
individual driver.
... Make sur e you are seated correctly
r=!)page 127 .
... Tur n the knob~ to adjust the disp lay .
Settings in the Infotainment system
... Sele ct: the I CARI function button > (Car)* Sys­
tem
control button > Driver assistance > Head­
up display > Head-up display contents or Dis-
play brightness. ..,
27

M N <( (.J
'SI: ,...., \!) 1.1'1
N \!) ,....,
Your authorized Audi dealer or a qualified service
station can interpret the code and perform the
necessary repair.
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­ tions, wh ich can increase the risk of a colli­
sion!
-
Electronic speed limiter
Your veh icle may be factory equipped with tires
that are rated for a maximum speed of 130 mph
(210 km/h). This is less than the maximum speed
of your vehicle. To reduce the risk of sudden tire
failure and loss of contro l if the vehicle is operat­
ed at excessive speeds, your vehicle also has an
e lectronic speed limiter. The electronic speed
limiter prevents your vehicle from going faster
tha n the tire speed rating. For more information
c>page240.
If the engine control unit receives fau lty vehicle
road speed signals, the Malfunction Indicator
Lamp (MIL)
¢4 will illumina te. If this occurs,
contact the nearest authorized Aud i dealer for as­
sistance.
S models
Your vehicle's top speed is e lectronically limited
to 155 mph (250 km/h).
If the engine control unit receives faulty vehicle
roadspeed s ignals, the Malfunction Indicator
Lamp (MIL)
¢4 will illuminate . If this occurs,
contact the nearest authorized Audi dealer for as­
sistance.
A WARNING
Always observe the posted speed limits and adjust your speed to suit prevailing road, traf­
fic and weather conditions. Never drive your
vehicle faster than the maximum speed rating
of the tires installed.
-
Instruments and indicator lights
29

Lights and Vi sion
- In cool or damp weather, the ins ide of the
headlights, turn signals and tail lights can
fog over due to the temperat ure difference
between the inside and outs ide. They w ill
clear shortly after switching them on. This
does not affect the service li fe of the light­
i ng.
Turn signals and high beam lev er
The lever on the left side of the steering column
is used to operate the turn signals and the high
beam as well as the headlight flasher.
F ig . 36 Tu rn signa l and hig h beam lever
The turn s ignal and high beam leve r has the fol ­
lowing f unctions:
Turn signals ¢¢@@
N
0 ,.._ 0 ±
~
• Pu sh the lever up as far as it can go t o turn on
t he righ t turn s ignal or down to tu rn on the left
tu rn s ignal
c:> fig. 36 .
• Move the lever brief ly until you meet resistance
and release it to flas h three times.
• Move the lever (up or down) unti l you meet re­
s istance and hold it there to determine the
flashing time for the tu rn s ignals.
High beam ~D @
• Push the lever forward to switch on the high
beam (vehicles with h igh beam assist *
c:>page44).
• Pull the lever back towards you to switch off
the h igh beam.
Headlight flasher ~D ©
• Pull the lever toward the steering wheel to use
the headlight f lasher.
44
Notes on these features
- The turn signals on ly work w it h the ignition
sw itche d on. The indicato r lights
II or Bin
the instrument cl uster c:> page 11 also blink.
- After you have tu rned a corner, the turn s ignal
sw itches off automatically .
- Th e
high beam works on ly when the he ad ligh ts
are on. The indi cator light
II in the instr ume nt
cl uste r ill uminates when the high beams a re
on.
- The
headligh t flasher works o nly as long as yo u
hold t he leve r - even if there are no lig hts
turned on. The indicator light
II in the instru­
ment cluster i lluminates when you use the
headlight f lasher .
A WARNING
Do not use the high beam or head light flasher
if you know that th ese could blind oncoming
traffic .
High beam assist
Applies to veh icles: with high beam assist
Fig . 3 7 Turn signal and high beam lever: sw itc hing high
bea m ass ist o n/off
A camer a on the rea rview mirror moun t ca n de­
tec t light sources from other road users . The high
beams switch on or off a utomat ica lly depen ding
o n the position of vehicles driving ahead and on­
coming vehicles, the vehicle speed and othe r en­
vironme nta l and traffic conditions.
Activating high beam assist
Req uirement: The AU TO light sw itch posit ion
must be selected and t he h igh beam assist m ust
be switched o n in the I nfotai nment system
c:> page45.

M N <( (.J
'SI: ,...., \!) ..,.,
N \!) ,....,
~ To activate the h igh beam assist, tap the lever
forward
(D . The ID indicator light appears in
the instrument cluster disp lay and the high
beam assist is switched on/off automatically.
The
El indicator ligh t also turns on if the high
beams are switched on .
Switching the high beam s on/off manually
If the high beams did not switch on/off automat­
ically as expected, you may switch them on or off
manually instead:
~ T o switch the high beams on man ually, tap the
lever forward
(D. The El indica tor light turns
on.
~ To switch the high beams off manua lly, pull the
lever back@. The high beam assist is deacti­
vated.
Operating the headlight flasher
~ To operate the headlight flasher when the high
beam assist is activated and high beams are
switched off, pull the lever back@. The high
beam assist remains act ive.
Messages in the instrument cluster display
r!IJ Audi adaptive light: system fault!
High beam assist: System fault
Drive to an authorized Aud i dealer or authorized
Aud i Service Fac ility immediately to have the
malfunct ion corrected. You can still switch the
hi gh beams on or off manually.
High beam assist : Unavailable No camera view
The camera view is blocked, for example by a
sticker or debr is.
The sensor is located between the interior rear­
view mirror and the windshie ld. Therefore, do not
p lace any st ickers in this area on the windshield.
A WARNING
-
High beam assist is only intended to assist
the driver. The driver is still responsible for
controlling the headlights and switching
them manually depending on light and visibil­
i t y cond itions. It may be necessary to operate
them manually in situations such as:
Lights and Vision
-In adverse weather conditions such as fog,
heavy ra in, blow ing snow or spray ing water.
- On roads where oncoming traffic may be
partially obscured, such as expressways.
- When there a re road users that do not have
sufficient lighting, such as bicyclers or
veh icles with dirty tail lamps.
- In tight curves and on steep slopes.
- I n poorly lit areas.
- With strong reflectors, such as signs.
-If the area of the windsh ield near the sensor
is fogged over, dirty, icy or covered with a
sticker.
Adjusting the exterior lighting
The settings are adjusted in the MMI.
~ Select: !CARI function button> (Car)* systems
control button > Vehicle settings > Exterior
lighting .
Automatic headlights
You can adjust the following sett ings in the Auto­
matic headlights
menu:
Headlights activation time -You can adjust if the
headlights switch on
Early , Med. or Late accord ­
ing to the sensit ivity of the light sensor.
Audi adaptive light* -You can switch adaptive
light
On and Off.
Automatic high beams*
You can switch the high beam assist on and off.
Daytime running lights
USA models:
You can switch the daytime running
lights
on and off .
Canada models:
The function cannot be turned
off. It is activated automat ica lly each t ime the ig­
nition is switched on. Th is menu item is show n
"greyed out".
Coming home, Leaving home
The coming home function illuminates the area
outside the vehicle when you switch the ignition off and open the driver's door. To turn the func-
t ion on, select
Lights when leaving car > On . ..,.
45

Ligh ts a nd Vi sion
by moving the lever to position ® within 10 sec ­
onds after the afterwipe. The afterwipe function
is reactivated the next time you switch the ign i­
tion on.
Cleaning the headlights *. The headlight washer
system* operates only when the low beam head­ lights are on. If you move the lever to position
® , the headlights and the night vision assist
camera* are washed in intervals.
A WARNING
-The rain sensor is only intended to assist the
dr iver . The driver is st ill responsible for
manually switching the wipers on according
to the v is ibility conditions.
- The w indshield may not be treated w ith wa­
te r-repell ing windsh ield coating agents. Un­
favorable conditions, such as wetness, dark­ ness or low sun, can resu lt in increased
glare, which increases the risk of an acci ­
dent. Wiper blade chatter is also possible.
- Properly functioning w indshield w iper
blades are required for a clear view and safe
driving ~
page 50, Replacing windshield
wiper blades.
(Jd) Note
- If there is frost, make sure the windshield
wiper blades are not frozen to the wind ­
s h ield. Switching on the winds hield wipers
when the blades are frozen to the wind­
sh ield can damage the wiper blades.
- Prior to using a car wash, the winds hield
wiper system must be switched off (lever in
position 0). This prevents unintentional
switching on and damage to the w indshield
wiper system.
(Di Tips
- The windshield wipers switch off when the
i gnition is turned off. You can act ivate the
windsh ield wipers after the ignition is
switched back on by moving the windsh ield
wiper lever to any pos it ion.
- Worn or dirty windshield w iper blades result
i n streaking. This can affect the rain sensor
so
f unction. Check your w indshield wiper
blades regu larly .
- T he washer fluid nozz les o f the windshie ld
washer system are heated at low tempera­
t ur es when the ignition is on.
- When stopping temporarily, such as at a traffic light, the speed of the windshield
wipers automatica lly reduces by one leve l.
Cleaning windshield wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner.
.,. Place the windshie ld wiper arms in the service
position
c:> page 50.
.,. Fold the windshie ld w iper arms away from the
w indshield.
A WARNING
Dirty windsh ield wiper b lades can impair vi­
sion, wh ich increases the risk of an accident .
Replacing windshield wiper blades
Fig. 47 Remov ing windshield wiper blades
Wiper serv ice position /bla de repl acement
posit ion
.,. Switch the ignit io n off and move the windshield
w iper lever to position @briefly
c:> page 49,
fig. 46. The w indshie ld w ipers move into the
service pos ition.
.,. To bring the w iper blades back into the or igina l
position, switch the ignition on and ope rate the
windshield wiper lever.
You can also tu rn the se rv ice position on or off in
t h e Info tainment sys tem: .,..

M N <( (.J
'SI: ,...., \!) ..,.,
N \!) ,....,
~ Switch the windshield wipers off (position@
c:>poge49, fig. 46).
~ Select: the ICARI function button > (Car)* Sys ­
tems
control button > Servi ce & cont rol > W ip ­
er cha nge posit ion
> On /O ff.
R emoving the wip er blade
~ Fold the windshield wiper arm away from the
windshield.
~ Press the locking knob@c:> fig. 47 on the wiper
blade. Hold the wiper blade firm ly.
~ Remove the wiper blade in the direction of the
arrow.
In sta ll in g t he w ip er bl ade
~ Insert the new wiper blade into the mount on
the wiper arm@ unti l you hear it latch into
place.
~ Place the wiper arm back on the windshield.
~ Turn the service pos ition off.
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice each
yea r.
0 Note
- Only fold the windshield wipe rs away when
i t is in the service pos ition. Otherw ise, you
r isk damag ing the pa int on the hood or the
windsh ield wiper motor.
- You should not move you r vehicle or ope rate
the windshie ld w iper lever when the wiper
arms are folded away from the windshield.
The windshield wipers would move back in ­
to t heir original position and could damage
the hood and windshield.
(D Tips
- You can also use the service pos ition, for ex ­
ample, if you want to protect the windshield
from icing by using a cover.
- You cannot activate the service position when the hood is open.
Light s and Vis ion
5 1