2016 AUDI A3 display

Instruments and indicator lights
(D Tips
For additional information on the diesel par­
ticulate filter, refer to¢
page 233.
!?) Engine speed limitation
A pp lies to ve hicles : w ith e ngin e spee d limit ation
[II Max. engine speed: XXXX rpm
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects the engine from overheating.
The engine speed limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once.
If the engine speed limitation was activated by
an engine control malfunction, the
[m indicator
light also turns on. Make sure the engine speed
does not go above the speed displayed, for exam­
ple when downshifting. Drive to an authorized
Audi dealer or authorized Audi Service Facility im­
mediately to have the malfunction corrected.
~ Engine oil level (min .)
II Check oil level
You may continue driving for the time being.
Check the engine oil level as soon as possible
¢page 240.
-If the engine oil level is too low, add engine oil
qpage242.
- If the engine oil level is correct and the indica­
tor light still turns on, drive at low engine
speed to an authorized Audi dealer or author­
ized Audi Service Facility.
'1::7' .., Engine oil sensor
• Oil level sensor: system fault!
The sensor to check the engine oil level has
failed. Drive to an authorized Audi dealer or au­
thorized Audi Service Facility immediately to have
the malfunction corrected.
Ill Oil level sens.: oil change necessary. Please
contact Service
24
The engine oil level is too high.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected .
(D Note
Refer to the description in the Owner's Man­
ual
q page 242, Checking the engine oil level
and ¢ page 242, Adding engine oil 5) Tank system
ID Please refuel
If the indicator light turns first turns on and this
message appears, the tank contains the follow­
ing amount of fuel:
- Front wheel drive: approximately 1.8 gallons (7
liters)
-All wheel drive: approximately
2.2 gallons (8.5
liters)
fiD Please refuel immediately
If the indicator light turns on the message ap­
pears, the fuel tank is almost empty. Refuel the
vehicle immediately.
ID Fuel tank malfunction! Please contact Serv­
ice
If the indicator light turns on and the message
appears:
- there is a malfunction in the fuel tank system,
or
- in vehicles with diesel engines, water may have
collected in the fuel filter.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.

Driver information system
Driver information
system
Overview
A pp lies to veh icles: w ith driver information system
F ig. 8 In strum ent cluster: Drive r Info rmation System (ex­
amp le)
Data is automatically recorded, processed and
d isplayed in the driver information system . Set­
tings for special equipment can be adjusted in
the MMI. Se lect the
I MENU ! button >Car > Sys­
tems* control button .
Introduction
The driver inform ation system is controlled
through the multifunction steering wheel
<=.> page 29, fig . 9.
The Driver Information System <=.> fig. 8 contains
the following information:
- @ Tab (register)
- @ Vehicle information
-© Status line (selector lever position, outside
temperature <=.>
page 11)
-@ On-board computer 0, fJ
-© Odometer and trip odometer or on-board
computer
D
N
0
LO 0
> OJ a,
The follow ing functions are possible, depending
on vehicle equipment:
28
@ ®
l. Tab ~ Vehicle functions:
On-board computer, time, date
<=.>page 29
Diesel engine*: remaining range for
Ad Blue <=.>
page 234
Plug-in hybrid drive*: energy flow in-
dicator
<=.> page 106
Plug-in hybrid drive*: range display
<=.>page 102
Efficiency program
<=.>page 31
Plug-in hybrid drive*: digital tachom -
eter
Digital speedometer
Assist
Aud i adapt ive cruise control*
<=.> page 13 2
Audi active lane assist*
<=.> page 142
Lap t i mer* <=.> page 32
Reduc ed display
2. Tab
~I&, Messages and ind icator lights
~ Service reminder indicator
<=.>page252
3. Tab fl I I Audio/ l'>l Radio
4. Tab "'Telephone*
5. Tab
~I~ Navigation*
The second tab is only visib le if at least one indi­
cator light or message is shown or if that system
is switched on.
Display
In the driver information system you will see :
Rad io stat ion or CD
T ime and date
<=.>page 10
Odometer, trip odometer <=.>page 11
Outside air temperature <=.>page 11
Service interval display <=.>page 252
Indicator lights and messages <=.>page 13
Digital speedometer
Lap timer*
<=.>page 32
Cruise control system <=.>page 130

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Speed warning ¢page 130
Selector lever positions C?page 89
On-board computer display ¢page29
Diesel engine*: remaining C?page 234
range for AdBlue
Plug-in hybr id drive*: d ig ital
C? page 29
tachometer
Plug-in hybrid drive*: range dis-
¢ page 102
play
On-board computer display
The on-board computer display monitors the dif­
ferent memory levels:
- Sho rt-term memory (on-board computer 1)
- Long-term memory (on-boa rd computer 2)
- Efficiency program
The following information can be displayed con­
secutively in the on-board computer:
- Tim e
- Date
- Estimated range based on current fuel level
- Estimated range based on current Ad Blue* level
- T ravel time
- Average consumption
- Average speed
- Distance
- Current fuel consumption
- Engine oil temperature indicator*
On-board computer O (short-term memory)
The short-term memory collects driving informa­
tion from the t ime the ignition is switched on un­
til it is switched off. If you cont inue dr iv ing
with­
in two hours
after switching the ignition off, the
new values are included when calculat ing the cur­
rent trip information. If stopped for more the
two hours, the short term memory is automati­
cally eras ed once you begin driving .
On-board computer fJ (long-term memory)
Unlike the short-term memory, the long-term
memory is not erased automat ically. Yo u can se­
l ect the time period for evaluating trip informa­
tion yourself .
Driver informa tion system
Efficiency program i1
The eff iciency p rogram can help you to use less
fuel<=>page31.
(0 Tips
- Th e on-board computer is controlled by the
left button fields on the multifunction
steering whee l.
- For information on using the other button
fields, such as the audio, telephone* and
navigation* functions, see the MMI owner's
manual.
- Disconnecting the battery causes all the
memory data to be erased .
Operation
Applies to vehicles : wi th drive r info rmation system
The driver information system is controlled with
the multifunction steering wheel.
Fig. 9 Mult ifunct ion steering wheel: Drive r Info rmation
System controls
Fig. 10 Drive r infor mation syste m: open ing t he vehicle
functions menu
In addition to information about the on-board
computer (on-board computer 1 , 2 and the effi­
ciency program) , informat ion about other sys­
tems can also be shown in the display.
29

Driver information system
You can identify which level (on-board computer
1, 2 or the efficiency program) is shown in the
d isp lay based on the small
0 , fJ or the nozzle
ii .
The tab@¢ page 28, fig. 8 is displayed once you
press the button
CD ~ fig. 9 on the mu ltifunction
steer ing wheel.
Operating
• Switch on the ignition. The last select function
is d isp layed.
• To switch between the tabs, press the rocker
button
CD to the left or right~ fig. 9.
• To access additional information below or
above, rotate the thumbwheel @down or up.
• To confirm a selection, press the thumbwheel
@ .
• To select a function programmed to a steering
wheel button, press the button
@ . For addi­
tional information, see ¢
page 30, Assigning
a function to a programmable steering wheel
button
Opening the Vehicle functions
• Select the first tab with the button CD-
• Press the button@. The Vehicle functions
menu is displayed¢ fig. 10.
,.. To select a menu item, turn and press the
thumbwheel @.
Resetting values to zero
• In the Vehicle functions menu, select On­
board computer or Efficiency program.
• Select a value in the desired trip computer or in
the efficiency program.
• To reset the values in a memory, press and hold
the thumbwheel @for one second .
Recalling indicator lights and messages
• Press the button CD repeatedly until the D tab
appears.
The
D tab is only v is ible when there is a mal·
function .
30
Assigning a function to a programmable
steering wheel button
• Select: the IM ENU I button > Car > Systems*
control button > Vehicle settings > Steering
wheel button programming .
The Q tab is only visible when there is at least
one indicator light or message displayed.
@ Tips
- If the vehicle battery is disconnected, all
memory values are erased .
- Information on the efficiency program
¢page 31.
- There is more information o n the multifunc­
t ion steering whee l in the
MMI* owner's
manual.
Boost indicator
App lies to vehicles: wi th boos t pressure indicator
Fig. 11 Instrument cluster: boost indicator
Boost pressure indicator (boost)
A bar graph that begins on the left and fills in to­
ward the r ight indicates the engine 's current load
(mean ing the current boost pressure).

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Efficiency program
Description
Appl ies to vehicles: with driver info rmation system
Fig . 1 2 Inst rument cluster : efficiency program (examp le)
Opening the efficiency program i1
.. Open the vehicle functions by press ing the but­
ton ®¢
page 29, fig. 9 and select the Efficien­
cy program menu item ¢ page 30.
The efficiency program can help you to use less
fuel. It evaluates driving info rmat ion in reference
to fu el consumption and shows other equipment
in fluenc ing co nsumption
¢ page 31. Fuel econ­
omy messages ¢
page 31 provide tips for effi­
cient dr iv ing .
The efficiency program receives data about the
d istance and fuel co nsumption from the on­
board computer
1. If the data in the efficiency
p rogram is de leted c::>
page 30, the va lues in the
on-board com puter 1 are a lso rese t.
Other equ ipment
Applies to vehicles: with driver information system
Fig . 1 3 Inst rume nt cluster: o ther eq uipment (examp le)
.. Turn the menu thumbwheel@c::> page 29,
fig. 9 in the efficie ncy program u nti l the other
Driver in forma tion system
equipment affecting consumption appea rs in
the display.
Ot her equ ipment that is current ly affecting fue l
consump tion is lis ted in the effic iency p rogram.
T he disp lay shows up to t hree other items of
equipment @. T he equ ipment using the most
f uel is listed first. If more than three items using
fuel a re switched on, the equipment t hat is c ur­
re ntly us ing the most fuel is d isp layed.
A scale @ also shows the current total consump­
tion of all other equipment.
Fuel economy messages
Applies to vehicles: with driver information system
Fig. 14 Instrument cluste r: economy tip (examp le)
Fuel economy messages are displayed when fuel
consumption is increased by certain conditions. If
yo u follow these economy tips, you can red uce
your vehicle 's fuel consumption. The messages
appea r automatically and are only displayed in
the efficiency program . The fuel economy mes­
sages turn off a utomatically a fter a ce rtain per i­
o d of t ime.
.,. To turn an economy message off immediately
after it appears, p ress any button on the m ulti­
fu nction stee ring wheel.
(D Tips
- Once you have turned an eco nomy tip off, it
w ill only appear aga in afte r you turn the ig­
nition o n ag ain.
- Th e economy tips are not d isp layed in every
ins tanc e, bu t rather in in terva ls over a per i­
od of time .
31

Driver information system
Lap timer and engine oil
temperature indicator
Introduction
Applies to vehicles: with lap timer (S models)
The engine oil temperature is only shown in the
lap timer display.
Lap timer
You can record and evaluate lap times with the
lap timer in the display
i=:,page 32, fig. 16. Th e
time is measured in minutes, seconds and
1/10
seconds . With lap times longer than 60 minutes,
the hour is also shown and the display of
1/10 seconds is removed.
The time measurement on an individua l lap ends
after
99 hours 59 minutes and 59 seconds. A
new lap starts automatically after that .
The measurement ends after a maximum of
30
laps. You can then evaluated the lap times or
start a new time measurement .
Engine oil temperature indicator
I f the engine o il temperature is below
140 °F
(60 °C), the 'l=:1: symbol followed by three hy­
phens"- --" and the °C un it is shown .
The engine has reached its operating tempera­
ture when the engine oil temperature is between
176 °f (80 °C) and 248 °f (120 °C) under nor­
mal d riving conditions. The engine oil tempera­
ture may be higher if there is heavy eng ine load
and high temperatures outside. This is not a
cause for concern as long as the .¢
page 20 or
Ill i=:,page 24 indicator lights in the display do
not blink.
A WARNING
Your focus should always be on driving your
vehicle safely . As the driver, you have com­
plete responsibility for safety in traffic . Only
use the functions such as the lap timer in such
a way that you always maintain complete con­
trol over your vehicle in all traffic s ituations.
32
.
@ Tips
You can retrieve information from the trip
computer while the lap timer stopwatch is
running.
Opening the lap timer and measuring time
Applies to vehicles: with lap timer (S models)
Fig. 15 Multi functio n stee ring whee l: co ntro ls
Fig. 16 Instrumen t cluster: lap timer
Opening the lap timer
M 0,
0
> g;:
.. Press the button @ on the multifunction steer­
ing wheel and turn the thumbwheel
®
i=:, fig. 15 until Lap timer ¢ fig. 16 appears.
.. Press the thumbwheel
® to confirm the selec­
tion.
Timing laps
.. To start timing, press the thumbwheel @while
on the
Lap 1 - press OK menu item. The time
measurement is shown in line @¢
fig. 16.
.. To measure the lap time, press the thumb­
wheel
® again while on the New lap· press OK
menu item. This starts timing the next lap at
the same time . The last time measurement
moves up to the top line@. Line @ contains
the current lap t ime .

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
If the symbol . is green dur ing the current lap
time measurement, the cur rent time is faster
than the prev ious best time. If the symbol. is
red, the current time is slower @.
Display ing split time and pausing timing
.. To d is p lay a split time [~], turn t he thumb-
whee l@ unti l
Split time appears in line@.
Press the thumbwheel @to confirm the selec­
t ion. The split t ime appears for approximately
10 seconds in line @. The t iming of the current
lap continues .
If yo u wou ld like to insert a pause
m immediate ­
l y after the sp lit time, first press the th umb­
wheel @and then the menu item
Press OK to go
back to confirm.
.. To insert a pa use, tur n the thumbwhee l@ unti l
Pause appea rs in the line @. P ress the thumb­
wheel @to confirm the select ion. T he pa use
symbol mappea rs in l ine @.
.. To continue timi ng, press the thumbwhee l@ .
I f t iming is paused, yo u can co ntinue i t late r even
if you swi tch the ig nition off .
Meaning of the i ndicators i n the center display
~ fig. 16:
CD Displ ay of last recor ded time
@ Symbols
:
-[OJ: start of t ime record ing
- •: slowest recorded t ime
-(i): fa stest recorded t ime
- r6J1 : spli t tim e
-m : pause
® Current t ime measurement
@ Men
u:
- Lap 1 (start)
- New lap (start anot her lap)
- Split time (time within section of the
route)
- Pause (interrupts measureme nt)
- Statistics (evaluation of lap t imes)
- Reset (all va lues are de leted)
Driver in forma tion system
Evaluating or resetting recorded times
Applies to vehicles: with lap tim er (S models)
You can evaluate the fastest, slowest and aver­
age lap times .
Fig. 17 Instrume nt cluste r: eva luat ing reco rde d tim es
..
"' 0 ;;,. CX) m
Aft er evalu ating the la p times, you c an con tinue
the current timing round or start over, mea ning
start lap 1 again.
.. To ev alu at e the ti me m eas uremen t, tu rn the
t humbwhee l@ ~
page 32 , fig. 15 unt il Statis­
tics appears in line@¢ page 32, fig . 16. Press
the t humbwheel @to confirm the se lection.
The dis play shows the fastest lap
" + ", the slow­
est lap" -" and the average lap time "0". To d is­
play t he individua l lap times, turn the thumb­
wheel @dow nward
C3 o r upwa rd !! .
.. To cont in u e the lap measurement that was
s tarted, press the t humbwheel @.
.. To re set t he time measureme nt to zer o, fi rst
p re ss the thum bwhee l@ , then tur n t he
t humbwhee l@
~ page 32 , fig. 15 unt il Reset
ap pears in line @ ¢ page 32, fig . 16 . Press the
thumbwhee l@ to confirm the select ion .
.. To restart the lap timer f or the new lap meas­
urement, press the th umbwheel @.
.. To ex it t he lap time r, press the b utton @ on
th e multifunction steering wheel an d kee p
t ur ning the thumbwhee l@ ¢
page 32, fig . 15
until a new menu i tem appears. Press t he
t humbwhee l@ to confirm the sele ct io n.
E xplanation of the evaluation¢
fig. 17:
@ A
ll laps
® II: fastest lap t ime
© . : s lowest lap t ime
@ rpj : aver age la p time
33

..... N
0 > CX)
..... I.Cl U"I
..... I.Cl .....
.. The LED blinks several times when you press a
button longer (convenience opening*) .
.. If the LED does not blink, the remote control
key battery is dead. The message
1:1 Please
change key battery
may also appear in the in­
strument cluster display . Replace the battery .
Replacing the remote control key battery
.. Pry the cover @off of the key (Dusing a coin
c::>fig . 20 .
.,. Insert the new battery with the "+" facing up .
.. Press the cover back onto the key until it clicks
into place .
We recommend having the battery replaced by
an authorized Audi dealer or authorized Audi
Service Facility .
@ For the sake of the environment
Dead batteries must be disposed of using
methods that will not harm the env ironment.
Do not dispose of them in household trash .
@ Tips
The replacement battery must meet the same
specifications as the orig inal battery.
Remote control key synchronization
The remote control key must be synchronized if
the vehicle does not lock and unlock with the re­
mote control.
.. Press the remote control key button~-
.. Insert the key in the driver's door lock within 30
seconds .
.,. Press the~ button or~ button .
Open ing and closing
Unlocking/locking by remote control
Fig. 21 Remote control key or conve nien ce key : button pro­
gramm ing
@ m Open
@ i'.D Close
© .:::::$Unlock luggage compartment lid
@ IPANIC !T rigger the alarm
... To unloc k the vehicle, press the button@~
c::>fig. 21 .
.. To lock the vehicle, bring the selector lever into
the P position and press the~ button
@.
.. To unlock the luggage compartment lid, press
the ~ button © briefly.
.,. To open the luggage compartment lid, press
and hold the~ button © for at least one sec­
ond .
... To trigger the alarm, press the red I PANIC ! but­
ton @. T he veh icle horn and emergency flash­
ers turn on.
.. To turn off the alarm, press the red I PANIC !
button @again .
If the vehicle is unlocked and a door or the lug­
gage compartment lid are not opened w ithin 45
seconds, the vehicle locks again automat ically.
This feature prevents the vehicle from being acci ­
dentally left unlocked over a long period of time.
This does not apply if you press the~ button ©
button for at least one second.
For vehicles with
safety central locking (selective
unlocking)
c::> page 40, only the driver's door
and the fuel f iller door are opened by pressing
the ~ button @ once, and the entire vehicle un-
locks when the button is pressed twice .
Ill>
37