Page 242 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
76MS006
7he level of the battery solution must be
kept between the upper level line (1)
and lower level line (2) at all times. If the
level is found to be below the lower level
line (2), add distilled water to the upper
level line (1). You should periodically check
the battery, battery terminals, and battery
hold-down bracket for corrosion. Remove
corrosion using a stiff brush and ammonia
mixed with water, or baking soda mixed
with water. After removing corrosion, rinse
with clean water.
If your vehicle is not going to be driven for
a month or longer, disconnect the cable
from the negative terminal of the battery to
help prevent discharge. 5 H S O D F H P H Q W R I W K H E D W W H U \
) R U ' $ ' L H V H O ( Q J L Q H 0 R G H O
64MS160
NOTE:
(For D13A Diesel Engine Model)
To approach the battery, remove the suc-
tion pipe (1). ) R U ' $ $ ' L H V H O ( Q J L Q H 0 R G H O
61MS2A006
NOTE:
(For D16AA Diesel Engine Model)
To approach the battery, loosen the bolts,
push the locks and remove the suction
pipe (1).
( ; $ 0 3 / (
(1)
( ; $ 0 3 / (
(1)
( ; $ 0 3 / (
Page 246 of 288
Downloaded from www.Manualslib.com manuals search engine 7-23INSPECTION AND MAINTENANCE
64MS0-74E
*Feature not available in the vehicle.
81A283
PRIMARY FUSE
(1) – Blank
(2) 20 A Power window timer
(3) 15 A Steering lock
(4) 20 A Rear defogger(5)
20 A
Sunroof*
(6)
10 A
DRL*
(7)
10 A
Heated mirror*
(8) 7.5 A Starting signal
(9) 15 A Accessory socket 2
(10) 30 A Power window
(11) 10 A Hazard
(12) 7.5 A BCM
(13) 15 A Ignition coil
(14) 10 A ABS control module
(15) 15 A Accessory socket
(16)
10 A
A-STOP controller*
(17) 15 A Horn
(18) 10 A Stop light
(19) 10 A Air bag
(20) 10 A Back-up light
(21) 15 A Wiper / Washer
(22) 30 A Front wiper
(23) 10 A Dome light(24)
15 A
4WD*
(25)
7.5 A
RR fog lamp*
(26) – Blank
(27) 7.5 A Ignition-1 signal
(28) 15 A Radio 2
(29) 10 A Accessory socket 3
(30) 15 A Radio
(31) 10 A Tail lamp
(32) 20 A D/L
(33) 7.5 A Cruise control
(34) 10 A Meter
(35) 7.5 A Ignition-2 signal
(36)
20 A
Seat heater*
WA R N I N G
Always be sure to replace a blown
fuse with a fuse of the correct amper-
age. Never use a substitute such as
aluminum foil or wire to replace a
blown fuse. If you replace a fuse and
the new one blows in a short period of
time, you may have a major electrical
problem. Have your vehicle inspected
immediately by your D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S.
BLOWN OK
Page 249 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
6 L G H 7 X U Q 6 L J Q D O / L J K W L I H T X L S S H G
76MH0A006
1) Remove the light housing (1) by sliding
to left with your finger.
76MH0A007
2) Turn the bulb holder (2) clockwise and
pull it out from the light housing.
76MH0A008
(4) Removal
(5) Install
3) To remove and install the bulb of the
turn signal light (3), simply pull out or
push in the bulb.
) U R Q W 7 X U Q 6 L J Q D O / L J K W
) U R Q W 3 R V L W L R Q / L J K W (Vehicle with the halogen headlights)
61MM0A030
(1)
(2)
(3)
(4)
(5)
(2)
(1)
Page 250 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
61MM0B077
1) Open the engine hood. To remove the
bulb holder of the front turn signal light
(1) or the front position light (2) from the
light housing, turn the holder counter-
clockwise and pull it out.
61MM0B078
(3) Removal
(4) Install
2) To remove the bulb of the front turn sig-
nal light (1) from the bulb holder, push in
the bulb and turn it counterclockwise. To
install a new bulb, push it in and turn it
clockwise.
To remove and install the bulb of the
front position light (2), simply pull out or
push in the bulb.
9 H K L F O H Z L W K W K H G L V F K D U J H K H D G O L J K W V
61MM0A091
To replace the bulb of the front turn signal
light (1), follow the procedure for the front
turn signal light bulb replacement of the
vehicle with the halogen headlights.NOTE:
Position function in discharge headlamp is
LED type, which is non replaceable.
(2)(1)
(2)
(1) (3)
(4)
( ; $ 0 3 / (
(1)
Page 251 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
) U R Q W ) R J / L J K W L I H T X L S S H G 1) Start the engine. Turn the steering wheel
to rotate the tires to the opposite side of
the fog light that requires replacement.
Then turn off the engine.
61MM0B079
2) Remove the screws (1).
61MM0B080
3) Remove the clips (2) by prying it off with
a flat blade screwdriver as shown in the
illustration.
61MM0B081
4) Open the end of the cover inside the
fender.
80JM071
5) Disconnect the coupler by pushing the
lock release. Turn the bulb holder coun-
terclockwise and remove it.
(1)
( ; $ 0 3 / (
(2)
( ; $ 0 3 / ( ( ; $ 0 3 / (
( ; $ 0 3 / (
Page 252 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
5 H D U & R P E L Q D W L R Q / L J K W
61MM0B082
1) Remove the bolts (1) and pull the light
housing (2) straight.
61MM0B083
2) To remove the bulb holder of the rear
turn signal light (3) or the tail/brake light
(4) from the light housing, turn the
holder counterclockwise and pull it out.
61MM0B084
(5) Removal
(6) Install3) To remove the bulb of the rear turn sig-
nal light (3) or the tail/brake light (4) from
bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
(2)(1)
(3)(4)
(3) / (4)
(5)
(6)
( ; $ 0 3 / (
Page 253 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
61MM0B085
NOTE:
When reinstalling the light housing, make
sure the clips are properly attached.
5 H Y H U V L Q J / L J K W
61MM0B088
1) Open the tailgate. Remove the clips (1)
by prying it off with a flat blade screw-
driver as shown in the illustration. Then,
pull out the trim (2).
61MM0B089
2) Disconnect the coupler (3) by pushing
the lock release. Turn the bulb holder ofthe reversing light (4) counterclockwise
and remove it.
61MM0B090
(5) Removal
(6) Install3) To remove and install the bulb of the
reversing light (4), simply pull out or
push in the bulb.
(2)
(1)
(3)
(4)
(4)
(5)
(6)
( ; $ 0 3 / (
Page 254 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
/ L F H Q V H 3 O D W H / L J K W
61MM0B086
1) Turn the cover (1) counterclockwise to
remove it.
61MM0B087
2) To remove and install the bulb of the
license plate light (2), simply pull out or
push in the bulb.
+ L J K P R X Q W 6 W R S / L J K W
80J100
1) Open the tailgate, and remove the nuts
(1) as shown in the illustration.
(1)
(2)
(1)
( ; $ 0 3 / (
