Page 236 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
& O X W F K 3 H G D O ) O X L G & R Q W U R O & O X W F K
64MS141
Check the clutch pedal for smooth opera-
tion and clutch fluid level from time to time.
If clutch dragging is felt with the pedal fully
depressed, have the clutch inspected by
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S. If the
clutch fluid level is near the “MIN” triangle
mark, fill it up to the “MAX” triangle mark
with MARUTI genuine brake fluid.
) X H O ) L O W H U
64MS175
The fuel filter works as a water sedimentor
as well.
Drain water according to the Periodic
Maintenance Schedule. To drain water:
1) Place a pan or ample rag under the fuel
filter drain nozzle.
2) Loosen the drain screw (1). The water
will be drained.
3) Tighten the drain screw when the water
changes to the diesel fuel.
7 L J K W H Q L Q J W R U T X H I R U G U D L Q V F U H Z
1 P N J P O E I W
% U D N H V % U D N H ) O X L G
64MS141
Check the brake fluid level by looking at
the reservoir in the engine compartment.
Check that the fluid level is between the
“MAX” and “MIN” triangle mark. If the
brake fluid level is near the “MIN” triangle
mark, fill it up to the “MAX” triangle mark
with MARUTI GENUINE BRAKE FLUID.
MAX
MIN
(1)
( ; $ 0 3 / (
MAX
MIN
Page 237 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
NOTE:With disc brakes, the fluid level can be
expected to gradually fall as the brake pads
wear. % U D N H 3 H G D OCheck if the brake pedal stops at the regular
height without spongy feeling when you
depress it. If not, have the brake system
inspected by your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S. If you doubt the brake pedal for
the regular height, check it as follows:
54G108
3 H G D O W R I O R R U F D U S H W P L Q L P X P G L V
W D Q F H ³ D ´ P P L Q With the engine running, measure the dis-
tance between the brake pedal and floor
carpet when the pedal is depressed with
approximately 30 kg (66 lbs) of force. The
minimum distance required is as specified.
Since your vehicle’s brake system is self-
adjusting, there is no need for pedal adjust-
ment.
If the pedal to floor carpet distance as mea-
sured above is less than the minimum dis-
tance required, have your vehicle inspected
by your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S.NOTE:When measuring the distance between the
brake pedal and floor wall, be sure not to
include the floor mat or rubber on the floor
wall in your measurement.
: $ 5 1 , 1 *
) D L O X U H W R I R O O R Z W K H J X L G H O L Q H V E H O R Z
F D Q U H V X O W L Q S H U V R Q D O L Q M X U \ R U V H U L
R X V G D P D J H W R W K H E U D N H V \ V W H P
Page 252 of 288
Downloaded from www.Manualslib.com manuals search engine , 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
5 H D U & R P E L Q D W L R Q / L J K W
61MM0B082
1) Remove the bolts (1) and pull the light
housing (2) straight.
61MM0B083
2) To remove the bulb holder of the rear
turn signal light (3) or the tail/brake light
(4) from the light housing, turn the
holder counterclockwise and pull it out.
61MM0B084
(5) Removal
(6) Install3) To remove the bulb of the rear turn sig-
nal light (3) or the tail/brake light (4) from
bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
(2)(1)
(3)(4)
(3) / (4)
(5)
(6)
( ; $ 0 3 / (
Page 265 of 288
Downloaded from www.Manualslib.com manuals search engine
( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
- D F N L Q J , Q V W U X F W L R Q V
75F062
1) Place the vehicle on level, hard ground.
2) Set the parking brake firmly and shift
into “R” (Reverse).
3) Turn on the hazard warning flasher if
your vehicle is near traffic.
4) Block the front and rear of the wheel
diagonally opposite of the wheel being
lifted.5) Place the spare wheel near the wheel
being lifted as shown in the illustration
in case that the jack slips.
54G253
63J10063J101
6) Position the jack at an angle as shown
in the illustration and raise the jack by
turning the jack handle clockwise until
the jack-head groove fits around the
jacking bar beneath the vehicle body.
7) Continue to raise the jack slowly and
smoothly until the tire clears the
ground. Do not raise the vehicle more
than necessary.
: $ 5 1 , 1 *
Page 268 of 288
Downloaded from www.Manualslib.com manuals search engine ( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
- X P S V W D U W L Q J L Q V W U X F W L R Q V
: K H Q - X P S 6 W D U W L Q J < R X U 9 H K L F O H
8 V H W K H ) R O O R Z L Q J 3 U R F H G X U H 1) Use only a 12-volt battery to jump start
your vehicle. Position the good 12-volt
battery close to your vehicle so that the
jump leads will reach both batteries.
When using a battery installed on
another vehicle, DO NOT LET THE
VEHICLES TOUCH. Set the parking
brakes fully on both vehicles.
2) Turn off all vehicle accessories, except
those necessary for safety reasons (for
example, headlights or hazard lights).
54MN259
3) Make jump lead connections as follows:
1. Connect one end of the first jump
lead to the positive (+) terminal of the
flat battery (1).
2. Connect the other end to the positive
(+) terminal of the booster battery (2).
3. Connect one end of the second jump
lead to the negative (–) terminal of the
booster battery (2).
4. Make the final connection to an
unpainted, heavy metal part (i.e.
engine mount bracket (3)) of the
engine of the vehicle with the flat bat-
tery (1).
: $ 5 1 , 1 *
Page 269 of 288
Downloaded from www.Manualslib.com manuals search engine
( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
4) If the booster battery you are using is fit-
ted to another vehicle, start the engine of
the vehicle with the booster battery. Run
the engine at moderate speed.5) Start the engine of the vehicle with the
flat battery.
6) Remove the jump leads in the exact
reverse order in which you connected
them.
7 R Z L Q JIf you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
: K H H O ' U L Y H : ' 0 D Q X D O 7 U D Q
V D [ O HManual transaxle vehicles may be towed
using either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the ground.
Before towing, make sure that the park-
ing brake is released.
2) From the rear, with the rear wheels lifted
and the front wheels on the ground, pro-
vided the steering and drivetrain are in
operational condition. Before towing,
make sure that transaxle is in neutral,
the steering wheel is unlocked (vehicle
without keyless push start system - the
ignition key should be in the “ACC” posi-
tion) (vehicle with keyless push start sys-
tem - the ignition mode is ACC), and the
steering wheel is secured with a clamp-
ing device designed for towing service.
& $ 8 7 , 2 1
& R Q Q H F W W K H M X P S O H D G W R W K H H Q J L Q H
P R X Q W E U D F N H W V H F X U H O \ , I W K H M X P S
O H D G G L V F R Q Q H F W V I U R P W K H H Q J L Q H
P R X Q W E U D F N H W E H F D X V H R I Y L E U D W L R Q D W
W K H V W D U W R I W K H H Q J L Q H W K H M X P S O H D G
F R X O G E H F D X J K W L Q W K H G U L Y H E H O W V
NOTICE
2 E V H U Y H W K H I R O O R Z L Q J L Q V W U X F W L R Q V
Z K H Q W R Z L Q J \ R X U Y H K L F O H
Page 285 of 288
Downloaded from www.Manualslib.com manuals search engine
6 3 ( & , ) , & $ 7 , 2 1 6
0 6 (
, 7 ( 0 / L J K W V : $ 7 7 $ * ( % 8 / % 1 R
Headlight Halogen 12V 60/55W H4
Discharge 12V 25W D5S
Front fog light 12V 35W H8
Position light 12V 5W W5W
LED –
Turn signal light Front 12V 21W PY21W
Rear 12V 21W PY21W
Side turn signal light 12V 5W WY5W
LED –
Tail/brake light 12V 21/5W P21/5W
High mount stop light 12V 5W W5W
Reversing light 12V 16W W16W
License plate light 12V 5W W5W
Interior light Glove box light (if equipped) 12V 1.4W –
Footwell light (if equipped) /
Instrument panel pocket light
(if equipped)LED –
Center 12V 10W –
Other lights 12V 5W W5W
Page 286 of 288
Downloaded from www.Manualslib.com manuals search engine 6 3 ( & , ) , & $ 7 , 2 1 6
0 6 (
*1 When tire replacement is necessary and if the specified load index and speed rated tire is not available, then use a tire of higher load
index and speed rating.
*2: The spare wheel provided with alloy wheel variant is steel wheel rim, hence follow 4 tire rotation only.
(Refer: Section
“Inspection and maintenance”)
, 7 ( 0 : K H H O V D Q G 7 L U H V
Tire size, front and rear
205/60R16 92H
*1*2
Tire size, spare
205/60R16 92H
*2 (Steel wheel)
Rim size 205/60R16 tire: 16X6J
Tire pressures For the specified tire pressure, see the Tire Information Label located
on the driver’s door lock pillar.
, 7 ( 0 5 H F R P P H Q G H G ) X H O / X E U L F D Q W V D Q G & D S D F L W L H V D S S U R [
Fuel 48 L
Engine oil D13A 3.2 L (replacement with oil filter)
D16AA 5.25 L (replacement with oil filter)
Engine coolant D13A 6.0 L (including reservoir tank)
D16AA 5.5 L (including reservoir tank)
Manual transaxle oil 5M/T 2.6 L
6M/T 2.1 L
Brake fluid / Clutch fluid Refill to the proper oil level according to the instructions in the “INSPEC-
TION AND MAINTENANCE” section.
