2015 SUZUKI NEXA warning
[x] Cancel search: warningPage 107 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
5 H P R W H & R Q W U R O O H U 2 X W V L G H : D U Q L Q JWhen either of the conditions described
below is met, the system issues the remote
controller outside warning by sounding the
interior and exterior buzzers. At the same
time, the immobilizer/keyless push start
system warning light comes on and the
master warning indicator light blinks.
• Any door is opened and then closed
while the remote controller is not inside
the vehicle and the engine is running or
the ignition mode has been changed to
“ACC” or “ON” by pressing the engine
switch.
• The remote controller is not inside the
vehicle when you attempt to start the
engine after changing the ignition mode
to “ACC” or “ON” by pressing the engine
switch.
61MM0A182
(1) Immobilizer/keyless push start sys-
tem warning light (blinks)
(2) Master warning indicator light (blinks)
NOTE:
• If the warning is given, locate the remote
controller as soon as possible.
• Any attempt to start the engine will fail
while the warning is active. The mes-
sage appearing on the information dis-
play in the instrument cluster will also
indicate this condition. Refer to “Informa-
tion display” in the “BEFORE DRIVING”
section for details.
• Normally, the immobilizer/keyless push
start system warning light should go out
and the master warning indicator light
should stop blinking shortly after the
remote controller is brought back inside
the vehicle. If they remain lit and blink-
ing, change the ignition mode to “LOCK”
(OFF) by pressing the engine switch and
then perform the engine starting opera-
tion. Refer to “Starting the Engine” in this
section.
• Always keep the remote controller with
you as the driver.
, Q W H U L R U : R U N D E O H $ U H D I R U ( Q J L Q H
6 W D U W L Q J , J Q L W L R Q 0 R G H 6 H O H F W L R Q
D Q G 5 H P R W H & R Q W U R O O H U 2 X W V L G H
: D U Q L Q J
61MM0B002
(1) Interior workable area
The interior workable area for these func-
tions is defined as all the interior spaces
except for the space above the instrument
panel.
NOTE:
• Even when the remote controller is in the
“interior workable area”, if it is in any of
the following conditions, you may not be
able to start the engine or select the igni-
tion modes, and the remote controller
outside warning may be given.
– The remote controller’s battery is low.
– The remote controller is affected by
strong radio signals or noise.
– The remote controller is in contact with
or covered by a metallic object.
(1)
(2)
(1)
Page 108 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
– The remote controller is in stowage
like the glove box or a door pocket.
– The remote controller is in the sun
visor pocket or on the floor.
• Even when the remote controller is out-
side the “interior workable” area, if it is in
any of the following conditions, you may
be able to start the engine or select the
ignition mode. The “remote controller
outside” warning may not be given at
that time.
– The remote controller is outside the
vehicle but very close to a door.
– The remote controller is on the instru-
ment panel.
3 D U N L Q J % U D N H / H Y H U
64MS185
(1) To set
(2) To release
(3) To release
The parking brake lever is located between
the seats. To set the parking brake, hold
the brake pedal down and pull the parking
brake lever all the way up. To release the
parking brake, hold the brake pedal down,
pull up slightly on the parking brake lever,
push the button on the end of the lever
with your thumb, and lower the lever to its
original position.
(2)
(3) (1)
( ; $ 0 3 / (
: $ 5 1 , 1 *
Page 109 of 288
![SUZUKI NEXA 2015 1.G Owners Manual Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
3 D U N L Q J % U D N H 5 H P L Q G H U % X ] ] H UA buzzer sou](/manual-img/20/7598/w960_7598-108.png "SUZUKI NEXA 2015 1.G Owners Manual Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
3 D U N L Q J % U D N H 5 H P L Q G H U % X ] ] H UA buzzer sou")
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
3 D U N L Q J % U D N H 5 H P L Q G H U % X ] ] H UA buzzer sounds intermittently to remind
you to release the parking brake if you start
the vehicle without releasing the parking
brake. Make sure that the parking brake is
fully released and the brake system warning
light turns off.
3 H G D O
80J2121
& O X W F K 3 H G D O The clutch pedal is used to disengage the
drive to the wheels when starting the
engine, stopping, or shifting the gearshift
lever. Depressing the pedal disengages the
clutch. % U D N H 3 H G D O Your vehicle is equipped with either front
and rear disc brakes or front disc brakes
and rear drum brakes. Depressing the
brake pedal applies both sets of brakes.
You may hear occasional brake squeal
when you apply the brakes. This is a nor-mal condition caused by environmental
factors such as cold, wet, snow, etc.
$ F F H O H U D W R U 3 H G D O This pedal controls the speed of the
engine. Depressing the accelerator pedal
increases power output and speed.
: $ 5 1 , 1 *
' R Q R W G U L Y H Z L W K \ R X U I R R W U H V W L Q J R Q
W K H F O X W F K S H G D O , W F R X O G U H V X O W L Q
H [ F H V V L Y H F O X W F K Z H D U F O X W F K G D P D J H
R U X Q H [ S H F W H G O R V V R I H Q J L Q H E U D N L Q J
(2)
(1)
(3) ( ; $ 0 3 / (
: $ 5 1 , 1 *
, I E U D N H V T X H D O L V H [ F H V V L Y H D Q G
R F F X U V H D F K W L P H W K H E U D N H V D U H
D S S O L H G \ R X V K R X O G K D Y H W K H E U D N H V
F K H F N H G E \ \ R X U D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S
: $ 5 1 , 1 *
' R Q R W U L G H W K H E U D N H V E \ D S S O \ L Q J
W K H P F R Q W L Q X R X V O \ R U U H V W L Q J \ R X U
I R R W R Q W K H S H G D O 7 K L V Z L O O U H V X O W L Q
R Y H U K H D W L Q J R I W K H E U D N H V Z K L F K
F R X O G F D X V H X Q S U H G L F W D E O H E U D N L Q J
D F W L R Q O R Q J H U V W R S S L Q J G L V W D Q F H V R U
S H U P D Q H Q W E U D N H G D P D J H
Page 110 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 ( 6 W D U W L Q J W K H ( Q J L Q H
9 H K L F O H Z L W K R X W . H \ O H V V 3 X V K
6 W D U W 6 \ V W H P
% H I R U H 6 W D U W L Q J W K H ( Q J L Q H
64MS146
1) Make sure the parking brake is set fully.
2) Shift into “N” (Neutral) and depress the
clutch pedal all the way to the floor. Hold
the clutch pedal while starting the
engine.
6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Turn the ignition switch to the “ON” posi-
tion and wait until the glow plug indicator
goes out if it comes on. Crank the engine
by turning the ignition key to “START”.
Release the key when the engine starts.
: D U P H Q J L Q H
Crank the engine by turning the ignition
key to “START”. Release the key when the
engine starts.
& D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warning
light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Hold the ignition key in “ON” position for
5-10 seconds to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
to have
the
engine inspected.
: $ 5 1 , 1 *
Page 112 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
tion. In this case, always let the engine
idle before stop it. 6 W D U W L Q J D & R O G D Q G : D U P ( Q J L Q H & R O G H Q J L Q H
Depress the clutch and brake pedals fully
and press the engine switch to crank the
engine. If the glow plug indicator light
comes on, the engine will start automati-
cally after the glow plug indicator light goes
off or 10 seconds past.
: D U P H Q J L Q H
Crank the engine by pressing the engine
switch to change the ignition mode to
“START”. & D X W L R Q Z K H Q V W R S S L Q J W K H H Q J L Q H Z L W K
W X U E R F K D U J H U
When stopping the engine after climbing or
high speed driving, let the engine idle for
about one minute or more (if it is not pro-
hibited) to cool down the turbocharger and
engine oil. This is to prevent the engine oil
from over-deteriorating. Deteriorated
engine oil will damage the bearings of the
turbocharger.
5 H V W D U W L Q J G L H V H O H Q J L Q H D I W H U I X H O
H P S W \ V W R S
If the engine stops and the low fuel warn-
ing light and the malfunction indicator light
come on, use the following procedure:
1) Fill the fuel tank.
2) Press the engine switch to change the
ignition mode to “ON” for 5-10 seconds
to feed fuel.
3) Perform above engine starting proce-
dure to start the engine.
If the malfunction indicator light still comes
on after the engine started, there may be
some problem with the engine. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to have
the engine inspected.
, I W K H 0 $ 6 7 ( 5 : $ 5 1 , 1 * L Q G L F D W R U O L J K W
E O L Q N V D Q G W K H H Q J L Q H F D Q Q R W E H V W D U W H G
Your keyless push start system remote
controller may not be sensed as being
within the interior workable area. Try again
after making sure that you have the remote
controller with you. If the engine still can-
not be started, the battery of the remote
controller may be discharged. You mustthen use the following method to be able to
start the engine.
58MST0302
1) Make sure the parking brake is set fully.
2) Shift to “N” (Neutral) and fully depress
the clutch pedal. Hold the clutch and
brake pedals fully depressed.
3) The “PUSH START SWITCH.” mes-
sage will appear on the information dis-
play in the instrument cluster. Press the
engine switch (1).
4) Within about 10 seconds of blinking of
the “MASTER WARNING” indicator
light in the instrument cluster, touch the
engine switch with the lock button end
of the remote controller (2) for about 2
seconds.
NOTE:
• If you still cannot start the engine after
several attempts using the above
NOTICE
' R Q R W F U D Q N W K H H Q J L Q H I R U P R U H
W K D Q V H F R Q G V D W D W L P H
, I W K H H Q J L Q H G R H V Q
Page 113 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
method, there may be a problem else-
where, such as a low battery. Contact
your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for inspection.
• The immobilizer/keyless push start sys-
tem warning light will come on for about
5 seconds while the master warning indi-
cator light is blinking. In addition, the
information display will show a certain
message during this time. Refer to
“Information Display” in the “BEFORE
DRIVING” section for details.
• You may customize the system to cause
the interior buzzer to sound once for the
remote controller out of sensing range
warning. Please contact an D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S for the
customization.
• If the battery of the remote controller is
about to be completely discharged, a
message warning this will appear on the
information display when the ignition
mode is changed to “ON” by pressing
the engine switch. For details on replac-
ing the battery, refer to the “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section.
5 H W X U Q L Q J W K H L J Q L W L R Q P R G H W R
³ / 2 & . ´ 2 ) )
Page 121 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
2 E V W D F O H , Q G L F D W L R Q E \ 3 D U N L Q J 6 H Q
V R U
64MS008
(1) Obstacle detected by rear center sen-
sors
(2) Obstacle detected by rear corner sen-
sors
(1) (2) (2)
( ; $ 0 3 / (
Upon detecting an obstacle, the parking sensor causes an interior buzzer to sound and a
symbol representing the obstacle appears on the information display in the instrument
cluster.
• A different symbol is displayed depending on the direction and distance of the obstacle.
• A buzzer located behind the rear seat sounds when a sensor at the rear detects an
obstacle.
• Warnings when obstacles are detected by corner sensors
• Warnings when obstacles are detected by center sensors
NOTE:
• Symbols are displayed with a short delay after the detection of obstacles.
• If the system detects multiple obstacles simultaneously, the display shows all of their
positions using the corresponding symbols. However, the buzzers will sound only for
the nearest obstacles. ' L V W D Q F H D S S U R [ % X ] ] H U 6 \ P E R O
45 – 60 cm
(18 – 24 in)Short beeps at short intervals Three lines
35 – 45 cm
(14 – 18 in)Short beeps at very short intervals Two lines
Less than 35 cm
(14 in)Continuous beep One line
' L V W D Q F H D S S U R [ % X ] ] H U 6 \ P E R O
60 – 150 cm
(24 – 59 in)Short beeps at long intervals
Three lines
45 – 60 cm
(18 – 24 in)Short beeps at short intervals
35 – 45 cm
(14 – 18 in)Short beeps at very short intervals Two lines
Less than 35 cm
(14 in)Continuous beep One line
Page 122 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
6 H W 6 H Q V R U VYou can select either the normal or trailer
mode of the parking sensor via the informa-
tion display. Refer to “Information Display”
in the “BEFORE DRIVING” section.
1 R U P D O P R G H
All sensors operate. Use this mode under
normal conditions.
7 U D L O H U P R G H
The rear corner and rear center sensors are
inhibited from operating. Use this mode
when towing a trailer.
NOTICE
0 D N H V X U H W K H Q R U P D O P R G H L V
V H O H F W H G Z L W K W K H S D U N L Q J V H Q V R U
Z K H Q V W H H U L Q J W K H Y H K L F O H L Q W R D
J D U D J H , I W K H S D U N L Q J V H Q V R U L V O H I W L Q
W K H W U D L O H U P R G H W K H U H D U F R U Q H U D Q G
U H D U F H Q W H U V H Q V R U V D U H Q R W I X Q F W L R Q
L Q J
: D U Q L Q J D Q G , Q G L F D W R U 0 H V V D J H VIf there is a problem or warning regarding the parking sensor system, a message is dis-
played on the information display in the instrument cluster, and a symbol blinks and the
buzzer sounds. If a message is displayed, follow its instruction.
0 H V V D J H 6 \ P E R O % X ] ] H U 3 U R E D E O H F D X V H D Q G U H P H G \
Two blinking
lines in a sen-
sor location.Series of
double
beepsThere may be problem with the
parking sensor system.
Have your vehicle inspected by
an D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S.
One blinking
line in a sensor
location.Series of
single
beepsThe indicated sensor is contami-
nated.
Wipe it clean with a soft cloth.