2015 SUZUKI NEXA check engine light
[x] Cancel search: check engine lightPage 100 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
( [ K D X V W * D V : D U Q L Q J
52D334
' D L O \ , Q V S H F W L R Q & K H F N O L V W % H I R U H ' U L Y L Q J
60A187
1) Make sure that windows, mirrors, lights
and reflectors are clean and unob-
structed.
2) Visually check the tires for the following
points:
– the depth of the tread groove
– abnormal wear, cracks and damage
– loose wheel nuts
– existence of foreign material such as
nails, stones, etc.
Refer to “Tires” in
Page 101 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
4) Make sure the hood is fully closed and
latched.
5) Check the headlights, turn signal lights,
brake lights and horn for proper opera-
tion.
6) Adjust the seat and head restraint.
7) Check the brake pedal and the parking
brake lever.
8) Adjust the mirrors.
9) Make sure that you and all passengers
have properly fastened the seat belts.
10)Make sure that all warning lights come
on as the ignition switch is turned to the
“ON” position or the engine switch is
pressed to change the ignition mode to
ON.
11)Check all gauges.
12)Make sure that the BRAKE SYSTEM
WARNING light turns off when the park-
ing brake is released.
Once a week, or each time you fill your fuel
tank, perform the following under-hood
checks:
1) Engine oil level
2) Coolant level
3) Brake fluid level
4) Battery electrolyte level
5) Windshield washer fluid level
6) Hood latch operation
Pull the hood release handle inside the
vehicle. Make sure that you cannot
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after check-
ing for proper latch operation. See theitem “All latches, hinges and locks” of
Page 105 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
NOTE:
In the presence of strong radio signals or
noise, you may not be able to change the
ignition mode to ACC or ON or to start the
engine using the engine switch. In this
case, the information display on the instru-
ment cluster will show the following mes-
sage: KEY FOB NOT DETECTED. 8 Q U H O H D V H G 6 W H H U L Q J / R F N : D U Q L Q JIf the steering lock remains engaged when
you press the engine switch to change the
ignition mode to “ON”, the information dis-
play in the instrument cluster shows the
message: “TRN. STEERING WHEEL TO
RELEASE LOCK”. Refer to “Information
Display” in the ³ % ( ) 2 5 ( ' 5 , 9 , 1 * ´ sec-
tion for details.
NOTE:
The steering lock may not be released if
some load is acting on the steering wheel.
If this happens, turn the steering wheel to
the right or left to relieve it from the load
before you press the engine switch again
to change to the desired ignition mode.
. H \ O H V V 3 X V K 6 W D U W 6 \ V W H P
L I H T X L S S H G Provided the keyless push start system
remote controller is within the “interior
workable area” (refer to the related expla-
nation in this section), you can use the
engine switch for starting the engine and
selecting an ignition mode (ACC or ON). In
addition, the following functions can be
used:
• Keyless entry function. Refer to “Keyless
Push Start System Remote Controller” in
the “BEFORE DRIVING” section for
details.
• Locking and unlocking doors (including
the tailgate) using a request switch.
Refer to “Keyless Push Start System
Remote Controller” in the “BEFORE
DRIVING” section for details.
• Immobilizer (anti-theft) function. Refer to
“Immobilizer System” in the “BEFORE
DRIVING” section for details. ( Q J L Q H 6 Z L W F K , O O X P L Q D W L R QThe engine switch is illuminated (lit) in the
following situations:
• When the engine is off and the driver’s
door is open or for 15 seconds after the
drivers door is closed.
• When the engine is off and the position
lights are on. The illumination will go out
when the position lights are turned off.
• When the engine is on and the position
lights and/or the headlights are on. Theillumination will go out when the head-
lights are turned off.
82K253
NOTE:
To save the battery, the illumination will be
automatically turned off when both of the
following conditions are simultaneously
met:
• The headlights and position lights are
turned off.
• A period of 15 minutes has elapsed after
opening the driver’s door. 6 H O H F W L R Q R I , J Q L W L R Q 0 R G H VPress the engine switch to select the
“ACC” or “ON” mode as follows when you
use an electric accessory or check the
operation of instruments without running
the engine.
1) Bring the keyless push start system
remote controller with you and sit in the
driver’s seat.
Page 126 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
, I W K H U H D U Y L H Z I U R P W K H U H D U Y L H Z F D P
H U D L V Q R W V K R Z Q R U W K H U H L V D S R R U
L P D J H• If the rear view from the rearview camera
is not shown.
– Check to make sure that the ignition
switch is in the “ON” position or the
ignition mode is “ON”.
– Check to make sure that the gearshift
lever is shifted to the “R” position.• If the image from the rearview camera is
poor.– Check to make sure that the camera
lens is not dirty.
– Check to make sure that light from the
sun or the beam of the headlights from
the vehicle behind is not shining
directly into the lens.
If the rearview camera system is still not
working properly after checking the above,
have the system inspected by an
D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S
as soon as
possible.
% U D N L Q J
60G165S
The distance needed to bring any vehicle to
a halt increases with the speed of the vehi-
cle. The braking distance needed, for exam-
ple, at 60 km/h (37 mph) will be
approximately 4 times greater than the
braking distance needed at 30 km/h (19
mph). Start to brake the vehicle when there
is plenty of distance between your vehicle
and the stopping point, and slow down
gradually.
3 R Z H U $ V V L V W H G % U D N H V L I
H T X L S S H G Your vehicle has power-assisted brakes. If
power assistance is lost due to a stalled
engine or other failures, the system is still
fully operational on reserve power and you
can bring the vehicle to a complete stop by
pressing the brake pedal once and holding
it down. The reserve power is partly used
up when you depress the brake pedal and
reduces each time the pedal is pressed.
Apply smooth and even pressure to the
pedal. Do not pump the pedal.
: $ 5 1 , 1 *
, I Z D W H U J H W V L Q W R W K H E U D N H G H Y L F H V
E U D N H S H U I R U P D Q F H P D \ E H F R P H S R R U
D Q G X Q S U H G L F W D E O H $ I W H U G U L Y L Q J
W K U R X J K Z D W H U R U Z D V K L Q J W K H X Q G H U
V L G H R I W K H Y H K L F O H W H V W W K H E U D N H V
Z K L O H G U L Y L Q J D W D V O R Z V S H H G W R V H H L I
W K H \ K D Y H P D L Q W D L Q H G W K H L U Q R U P D O
H I I H F W L Y H Q H V V , I W K H E U D N H V D U H O H V V
H I I H F W L Y H W K D Q Q R U P D O G U \ W K H P E \
G U L Y L Q J V O R Z O \ X Q W L O W K H E U D N H V K D Y H
U H J D L Q H G W K H L U Q R U P D O H I I H F W L Y H Q H V V
: $ 5 1 , 1 *
( Y H Q Z L W K R X W U H V H U Y H S R Z H U L Q W K H
E U D N H V \ V W H P \ R X F D Q V W L O O V W R S W K H
Y H K L F O H E \ S U H V V L Q J W K H E U D N H S H G D O
K D U G H U W K D Q Q R U P D O O \ U H T X L U H G + R Z
H Y H U W K H V W R S S L Q J G L V W D Q F H P D \ E H
O R Q J H U
Page 136 of 288
Downloaded from www.Manualslib.com manuals search engine ' 5 , 9 , 1 * 7 , 3 6
0 6 (
2) Don’t use hand-braking unless una-
voidable. It causes the vehicle to skid
and a rearend collision occur. It is espe-
cially dangerous when the tyres are
worn, for they allow a larger skid.
72F-08-012
Use foot brake in three stages
1.Warn the vehicle behind you
2.Gradually apply the brake.
3.Bring the vehicle to a halt.
3) When driving on a downhill, try not to
apply the brake but use the engine
brake effectively. Overuse of the foot
brake may result in total brake failure.
4) Avoid reckless high speed driving and
try to drive at a safe speed suitable for
the road conditions while maintaining a
constant speed.
72F-08-015
5) The higher the speed, the narrower the
driver’s visual range becomes. In such
a state, it is difficult to anticipate any
hazard and the driver feels much
fatigued.
6) Never do sharp handling during high
speed driving. You will lose your control
over your vehicle.
7) When overtaking or changing the lane
while driving at a high speed, keep an
ample vehicle-to-vehicle distance. / R Q J G L V W D Q F H G U L Y L Q J
1) Be sure to perform safety checks before
starting a trip.
2) Take rest at certain intervals to prevent
an accident which may occur when you
are sleepy or tired.
72F-08-020
1 L J K W W L P H G U L Y L Q J
1) Drive more slowly at night than in the
daytime, for the visual range is
restricted at night.
2) Don’t overtake other vehicles at night.
Darkness bothers your sense of speed
and hinders your judgment on the vehi-
cle-to-vehicle distance.
3) Don’t use the high headlight beam
unless its use is inevitable. Its dazzle
may blitz the driver of the oncoming
vehicle, thus causing an accident.
4) Always keep the window glasses clean.
Don’t operate the windshield wiper
Page 209 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
% D W W H U \ , Q V W D O O D W L R QInstall a lithium battery (CR2025) with the poles facing the correct direction.
% D W W H U \ U H S O D F H P H Q W W L P L Q J
• When battery power is depleted, the button may not be operable. If the remote controller
does not operate, replace the battery and check the operation.
& D X W L R Q R Q E D W W H U \
• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or
explosion.
If battery leakage has occurred, wipe the
container first then install a new battery. If
the battery solution contacts the skin, wash
off with water completely.
& D X W L R Q R Q 5 H P R W H & R Q W U R O O H U• Do not leave the remote controller in an
area exposed to direct sunlight, such as
on the dashboard or steering wheel. The
remote controller may deform because of
the heat, (Be especially careful of the
dashboard exposed to direct sunlight in
the summer, as it will become extremely
hot).
: $ 5 1 , 1 *
Page 271 of 288
Downloaded from www.Manualslib.com manuals search engine
( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
If the high engine coolant temperature
warning light does not go off:
1) Turn off the engine and check that the
water pump belt and pulleys are not
damaged or slipping. If any abnormality
is found, correct it.
2) Check the coolant level in the reservoir.
If it is found to be lower than the “LOW”
line, look for leaks at the radiator, water
pump, and radiator and heater hoses. If
you locate any leaks that may have
caused the overheating, do not run the
engine until these problems have been
corrected.
3) If you do not find a leak, carefully add
coolant to the reservoir and then the
radiator, if necessary. (Refer to “Engine
Coolant” in the “INSPECTION AND
MAINTENANCE” section.)
NOTE:
If your engine overheats and you are
unsure what to do, contact your D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S.
65D350d
: D U Q L Q J 7 U L D Q J O H
MHO-07-001
In case of vehicle break-down or during
emergency stopping, where, your vehicle
could become a potential traffic hazard,
keep the warning triangle, provided with
your vehicle, on the road free from any
obstacles behind your vehicle so as to
warn the approaching traffic, at an approxi-
mate distance of 50-100 m. The reflecting
side of the triangle should face the on com-
ing traffic. Please activate the hazard
warning lamps before alighting the vehicle
to keep the warning triangle.
: $ 5 1 , 1 *
Page 278 of 288
Downloaded from www.Manualslib.com manuals search engine $ 3 3 ( $ 5 $ 1 & ( & $ 5 (
0 6 (
6) Check carefully for damage to painted
surfaces. If there is any damage, touch-
up the damage following the procedure
below:
1. Clean all damaged spots and allow
them to dry.
2. Stir the paint and touch-up the dam-
aged spots lightly using a small
brush.
3. Allow the paint to dry completely.
: D [ L Q J
60B211S
After washing the vehicle, waxing and pol-
ishing are recommended to further protect
and beautify the paint.
• Only use waxes and polishes of good
quality.
• When using waxes and polishes,
observe the precautions specified by the
manufacturers.
NOTICE
, I \ R X X V H D Q D X W R P D W L F F D U Z D V K
P D N H V X U H W K D W \ R X U Y H K L F O H