2015 Peugeot RCZ ignition

43
RCZ_en_Chap02_ouvertures_ed01-2015
OPERATING FAULT
L
OCKING
THE
VEHICLE WITHOUT
ACTIV
ATING
THE


ALARM
F Lock or deadlock the vehicle using the key in the driver's door lock.
When the ignition is switched on, fixed illumination of the indicator lamp
in the button indicates a fault with the system.
Have

it checked by a PEUGEOT

dealer or a qualified workshop.
FAILURE OF THE REMOTE CONTROL
To deactivate the monitoring functions:
F

unlock the vehicle using the key in the driver's door lock,
F


open the door; the alarm is triggered,
F


switch on the ignition; the alarm stops; the indicator lamp in the
button goes of

f.
TRIGGERING OF THE ALARM
The monitoring functions remain active until the alarm has been
triggered eleven times in succession.
When the vehicle is unlocked using the remote control, rapid
flashing
of the indicator lamp in the button informs you that the
alarm was triggered during your absence. When the ignition is
switched

on, this flashing stops immediately.
This
is indicated by sounding of the siren and flashing of the direction
indicators for thirty seconds.
2 minutes after closing the last door or the boot, the system is activat\
ed
automatically
.
F To
avoid triggering the alarm when entering the vehicle, first press
the remote control unlocking button.
AUTOMATIC ACTIVATION *
* Depending on country of sale.
2/
ACCESS

44
RCZ_en_Chap02_ouvertures_ed01-2015
ELECTRIC WINDOWS
Fitted with a safety anti-pinch system.
A.
Left-hand electric window
.
B.

Right-hand electric window
.
ONE-TOUCH ELECTRIC WINdOWS
There are two options:
-
manual mode
F


Press or pull the switch gently
. The window stops when the
switch is released.
-

automatic mode
F

Press or pull the switch firmly.
The
window opens or closes fully
when the switch is released.
F


Pressing the switch again stops the movement of the window
.The electric window switches remain operational for approximately
45 seconds after the ignition is switched off or until the vehicle is
locked after a door is opened.
If the passenger's window cannot be operated from the driver's
door control panel, carry out the operation from the control panel
of the passenger door.
After approximately ten consecutive complete opening/closing
movements of the window, a protection function is activated which
only authorises closing of the windows, so as to prevent damage
to the electric window motor.
Once the window is closed, the switches will become operational
again after approximately 40 minutes.
Safety anti-pinch
When the window rises and meets an obstacle, it stops and partially
lowers again.
If the window cannot be closed (for example, in the presence of
ice), immediately after the movement is reversed:
F

press and hold the switch until the window opens fully
,
F

then pull the switch immediately and hold it until the window
closes,
F


continue to hold the switch for approximately one second after
the window has closed.
The safety anti-pinch function is not operational during these
operations.

45
RCZ_en_Chap02_ouvertures_ed01-2015
Reinitialisation
If a window does not rise automatically, after reconnecting the battery
for example, its operation must be reinitialised:
F
pull the switch until the window stops,
F


release the switch and pull it again until the window closes fully
,
F

continue to hold the switch for approximately one second after the
window has closed,
F


press the switch to lower the window automatically to the low
position,
F


when the window has reached the low position, press the switch
again for approximately one second.
The safety anti-pinch function is not operational during these
operations. Always remove the key from the ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during operation of the electric
windows, you must reverse the movement of the window

. To do
this, press the switch concerned.
When the driver operates the switch for the passenger's electric
window, they must ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the passengers use the electric
windows correctly.
Be aware of children when operating the windows.
2/
ACCESS

48
RCZ_en_Chap02_ouvertures_ed01-2015
Pressing the central locking control unlocks the vehicle.
Opening a door from the inside, when stationary, also unlocks the
vehicle, but the vehicle will be locked again when the speed exceeds
6 mph (10 km/h).
Activation / deactivation
You can activate or deactivate this function.
F
With the ignition on, press the button for more than two seconds.
A


confirmation message appears in the screen.
EMERGENCY LOCKING
To lock or unlock the doors mechanically in the event of a central
locking
system failure or flat battery.
Locking the driver's door
F Insert the key in the lock, then turn it to the right.
Unlocking the driver's door
F Insert the key in the lock, then turn it to the left.
Locking the passenger door
F Using the key, remove the black cap on the edge of the door.
F
Insert the key in the cavity without forcing, then without turning it,
move the the latch sideways towards the interior of the door

.
F Remove
the key and refit the cap.
Unlocking the passenger door
F Pull the interior door opening control.
ANTI-INTRUSION SECURITY
This function permits automatic and simultaneous locking of the doors,
boot lid and fuel filler flap as soon as the vehicle speed exceeds 6 mph
(10 km/h).
Operation
If one of the doors is open, the automatic central locking does not take\

place.
If the boot lid is open, the automatic central locking of the doors is
active.

51
RCZ_en_Chap03_confort_ed01-2015
FRONT SEATS
Seat with integral head restraint, consisting of a seat cushion and a se\
at
back which can be adjusted to adapt your position for ease of driving
and comfort.
ELECTRIC A dj USTMENTS
Forwards-backwards adjustment Seat cushion height adjustment
F Push the control forwards or rearwards to slide the seat. F
T
ilt the rear part of the control upwards or downwards to obtain the
required height.
The electrical functions of the seat are deactivated approximately
one minute after the ignition is switched off.
To reactivate them, switch on the ignition.
Carry out these adjustments with the engine running to avoid
discharging the battery.
Seat back angle adjustment
F Tilt the control forwards or rearwards to adjust the angle of the seat
back.
Before moving the seat backwards, ensure that there is nothing
that might prevent the full travel of the seat, so as to avoid the risk \
of of jamming the seat caused by the presence of objects on the
floor

behind

the

seat

or

rear

passengers.

If

the

seat

jams,

stop

the

movement immediately

.
3/
EASE OF USE and COMFORT

53
RCZ_en_Chap03_confort_ed01-2015
STORING DRIVING POSITIONS
System which takes into account the electrical settings of the driver's \
seat and the door mirrors. It enables you to store two positions using
the buttons on the side of the driver's seat.
STORING A POSITION
Using buttons M / 1 / 2
F Switch on the ignition.
F
Adjust your seat and your door mirrors.
F


Press button
M, then press button 1 or 2 within four seconds.
An audible signal is heard indicating that the settings have been
stored.
RECALLING A STORE d POSITION
Storing a new position cancels the previous position.
Using button 1 or 2
F Press and hold button 1 or 2 until the audible signal is heard
indicating the end of the adjustment.
When the ignition is off, after a few consecutive position recalls,
the function will be deactivated until the engine is started,
to
prevent discharging of the battery.
3/
EASE OF USE and COMFORT

56
RCZ_en_Chap03_confort_ed01-2015
Folding
F From outside: lock the vehicle using the remote control or the key.
F
From inside: with the ignition on, pull the control A

in the central
position rearwards.
If the mirrors are folded using control A, they will not unfold when
the vehicle is unlocked. Pull again on control A.
Unfolding
F From outside: unlock the vehicle using the remote control or
the
key.
F

From inside: with the ignition on, pull the control A

in the central
position rearwards.
The folding and unfolding of the door mirrors using the remote
control
can be deactivated by a PEUGEOT

dealer or a qualified
workshop.
If necessary the mirrors can be folded manually

.
Automatic tilting in reverse gear
System which provides a view of the ground during parking
manoeuvres in reverse gear.
Programming
F With the engine running, engage reverse gear.
F
Select and adjust the left-hand and right-hand mirrors in
succession.
The adjustment is stored immediately

.
Switching on
F With the engine running, engage reverse gear .
F
Move control
A to the right or to the left to select the corresponding
mirror.
The glass of the mirror selected tilts downwards, in accordance with its\

programming.
Switching off
F Exit reverse gear and wait ten seconds.
or
F

Return control A

to the central position.
The mirror glass returns to its initial position.
The mirror glass also returns to its initial position:
-

if the speed exceeds 6 mph (10 km/h),
-


if the engine is switched of
f.

64
RCZ_en_Chap03_confort_ed01-2015
COURTESY LAMP
A. Courtesy lamp
B.
Map reading lamps
COURTESY LAMP
In this position, the courtesy lamp comes on gradually:
-

when the vehicle is unlocked,
-


when the key is removed from the ignition,
-


when a door is opened,
-


when the remote control locking button is activated, in order to
locate your vehicle. It switches of

f gradually:
-
when the vehicle is locked,
-

when the ignition is switched on,
-

30 seconds after the last door is closed.
Permanently of
f.
Permanent lighting.
With the "permanent lighting" mode, the duration of lighting varies,
depending on the circumstances:
-
with the ignition of
f, approximately ten minutes,
-
in energy economy mode, approximately thirty seconds,
-

with the engine running, unlimited.
MAP
REA d ING LAMPS
F With the ignition on, press the corresponding switch.