2015 Peugeot RCZ ignition

24
RCZ_en_Chap01_controle-de-marche_ed01-2015
Service overdue
For a few seconds after the ignition is switched on, the spanner
flashes to indicate that the service must be carried out as soon as
possible.
Example: the service is overdue by 300 miles (300
km).
For a few seconds after the ignition is switched on, the central screen \
indicates:
The spanner remains on in the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the type of motoring the vehicle is used for.
Therefore, the spanner may also come on if you have exceeded
the
period since the last service specified in the manufacturer's
service schedule.
This indication applies only to HDi Diesel engines.
Service indicator reset
Retrieving the service information
You can access the service information at any time.
This information appears when running through the manual check
procedure.
F Briefly press the "CHECK/000" button.
The service information is displayed for a few seconds on the
instrument panel central screen, then disappears.
Following this operation, if you wish to disconnect the battery

,
lock the vehicle and wait at least five minutes for the reset to be
registered.
After each service, the service indicator must be reset.
If you have carried out the service on your vehicle yourself:
F

switch of
f the ignition,
F
press and hold the
"CHECK/000" button,
F

switch on the ignition; the distance recorder display begins a
countdown,
F

when the instrument panel central screen indicates
"=0"
, release
the button; the spanner disappears from the small screen.

25
RCZ_en_Chap01_controle-de-marche_ed01-2015
MANUAL CHECK
This function allows you to check the status of the vehicle (reminder o\
f
the active alert warnings) and the service information.
F With
the engine running, to start a manual check, briefly press the
"CHECK/000" button on the instrument panel.
If no faults have been detected,

"CHECK OK" appears in the
instrument panel central screen.
If a "minor" fault has been detected, the warning lamp concerned then
"CHECK OK" appear in the instrument panel central screen. Contact a
PEUGEOT


or a qualified workshop.
If a "major" fault has been detected, only the warning lamps concerned
appear in the instrument panel central screen. Have it checked by a
PEUGEOT


dealer or a qualified workshop.
dISTANCE RECORdERS
The total and trip distances are displayed for thirty seconds when the
ignition is switched off, when the driver's door is opened and when the
vehicle is locked or unlocked.
Measures the total distance travelled by the vehicle since its first
registration.
Total distance recorder
F With the ignition on, press and hold this button until zeros appear .
Trip distance recorder
Measures the distance travelled since it was last reset to zero by the
driver.
1/
MONITORING

26
RCZ_en_Chap01_controle-de-marche_ed01-2015
LIGHTING dIMMER
Permits manual adjustment of the brightness of the instruments and
controls to suit the ambient light level. Only operates when the vehicle\

lighting is on, with the exception of the daytime running lamps.
Activation
F Press the button to change the brightness of the instruments and
controls.
F

When the lighting reaches the minimum setting, release the button,
then press again to increase it.
or
F


When the lighting reaches the maximum setting, release the button,
then press again to reduce it.
F

When the lighting reaches the level of brightness required, release
the button.
deactivation
When the vehicle lighting is off, or in day mode on vehicles fitted with daytime running lamps, pressing the button does not have any effect.
CLOCK
The analogue clock, located between the central vents of the
dashboard, does not have an adjustment button.
To set the time, refer to the section relating to your multifunction
screen's
configuration menu.
The clock is synchronised with the multifunction screen time; once the
the
setting has been confirmed on the multifunction screen, the hands
will turn to synchronise with the screen, and each time the ignition is \
switched on.

36
RCZ_en_Chap01_controle-de-marche_ed01-2015
You can adjust the angle of the screen to one of four defined positions, by repeated presses on the front or back of the control B
. The position
of the screen is memorised on closing.
Adjusting the angle of the screen
The screen opens automatically when the ignition is switched on. It
closes automatically three seconds after switching off the ignition if the
audio and telematics system is switched off.
ACCESS TO THE RETRACTABLE SCREEN
You can open or close the screen at any time, with the ignition on, using\

control A.
-

Press button
A: the screen folds.
-

Press button
A again: the screen opens again.
If you have closed the screen, it will open again automatically:
-

on switching on the audio and navigation system (unless it
had been closed manually while the system was in operation),
-


when an outgoing telephone call is made,
-


when a voice command is given,
-


when a warning message linked with the ST
OP warning lamp
is displayed (P
EUGEOT
Connect Navigation (R
T6)).

39
RCZ_en_Chap02_ouvertures_ed01-2015
Folding the key
F First press this button to fold the key.
LOCATING YOUR VEHICLE
R

EMOTE
CONTROL
PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction, \
you can no longer unlock, lock or locate your vehicle.
F
First of all, use the key in the lock to unlock or lock your vehicle.
F


Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT

dealer as soon as
possible.
Reinitialisation
F Switch of f the ignition.
F
T
urn the key to position 2 (Ignition on) .
F

Press the closed padlock immediately for a few seconds.
F


Switch of
f the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620 / 3 volts.
If the battery is flat, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
F


Unclip the casing using a coin at the notch.
F

Slide the flat battery out of its location.
F

Slide the new battery into its location observing the original
direction.
F


Clip the casing.
F


Reinitialise the remote control.
This function allows you to identify your vehicle from a
distance, particularly in poor light.

Your vehicle must be
locked.
F
Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will\

flash

for

around

ten

seconds.
If you do not press the button when folding the key, there is a risk
of damage to the mechanism.
2/
ACCESS

40
RCZ_en_Chap02_ouvertures_ed01-2015
LOST KEYS
Go to a PEUGEOT dealer with the vehicle's registration document, your personal identification documents and if possible the key code label.
The PEUGEOT

dealer will be able to look up the key code and the transponder code required to order a new key.
LOCKING THE VEHICLE
Driving with the doors locked may make access to the passenger compartment by the emergency services more difficult in an emergency.
As a safety precaution, never leave children alone in the vehicle, excep\
t for a very short period.
In all cases, it is essential to remove the key from the ignition switch\
when leaving the vehicle.
REMOTE CONTROL
The high frequency remote control is a sensitive system; do not operate it while it is in your pocket as there is a possibility that it may unlock the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range \
and out of sight of your vehicle.
You run the risk of stopping it from
working and the remote control would have to be reinitialised.
No remote control can operate when the key is in the ignition switch, ev\
en when the ignition is switched off, except for reinitialisation.
ANTI-THEFT PROTECTION
Do not make any modifications to the electronic engine immobiliser system; this could cause malfunctions.
Do not throw the remote control batteries away , they contain metals which are harmful to the environment.
Take them to an approved collection point.
WHEN PURCHASING A SECON d- HAN d VEHICLE
Have the pairing of all of the keys in your possession checked by a PEUG\
EOT dealer, to ensure that only your keys can be used to open and
start the vehicle.

41
RCZ_en_Chap02_ouvertures_ed01-2015
ALARM*
System which protects and provides a deterrent against theft and break-
ins. It provides the following types of monitoring:
- exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a door, the boot, the
bonnet...
- interior volumetric
The system checks for any variation in the volume in the passenger compa\
rtment.
The alarm is triggered if anyone breaks a window, enters the passenger
compartment or moves inside the vehicle.
- tilt
The system checks for any change in the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted, moved or knocked.For all work on the alarm system, contact a PEUGEOT dealer or a
qualified
workshop.
LOCKING THE VEHICLE WITH FULL ALARM
SYSTEM
Activation
F Switch off the ignition and get out of the vehicle.
F
Press the locking button on the remote control.
The

monitoring system is active: the indicator lamp in the button flashes
once per second.
After the locking button on the remote control is pressed, the exterior \
perimeter monitoring is activated after a delay of 5 seconds and the
interior volumetric and anti-tilt monitoring after a delay of 45 seconds\
.
deactivation
F Press the unlocking button on the remote control.
The alarm system is deactivated: the indicator lamp in the button goes o\
f f.
Self-protection function
The system checks for the putting out of service of its
components.
The alarm is triggered if the battery, the central control or the siren
wiring are put out of service or damaged.
* According to country. If an opening (door, boot...) is not closed fully, the vehicle is not
locked but the exterior perimeter monitoring will be activated after
a delay of 45 seconds at the same time as the interior volumetric
and anti-tilt monitoring.
2/
ACCESS

42
RCZ_en_Chap02_ouvertures_ed01-2015
LOCKING THE VEHICLE WITH EXTERIOR
PERIMETER

MONITORING
ONL
Ydeactivation of the interior volumetric and anti-tilt monitoring
F Switch off the ignition.
F
Within ten seconds, press the button until the indicator lamp is on
continuously

.
F

Get out of the vehicle.
F


Press the locking button on the remote control immediately
.
The exterior perimeter monitoring alone is activated: the indicator lamp\

in
the button flashes once per second.
Reactivation of the interior volumetric and anti-tilt monitoring
F Press the unlocking button on the remote control to deactivate the
exterior perimeter monitoring.
F

Press the locking button on the remote control to activate all the
monitoring functions.
The

indicator lamp in the button again flashes once per second.
Deactivate the interior volumetric and anti-tilt monitoring to avoid
unwanted triggering of the alarm in certain cases such as:
-

leaving a pet in the vehicle,
-

leaving a window partially open,
-
washing your vehicle,
-

changing a wheel,
-


having your vehicle towed,
-


transport by sea. T

o be effective, this deactivation must be carried out each time the
ignition is switched off.