2015 MITSUBISHI L200 change wheel

NOTElDo not push two or more of the steering
wheel remote control switches at the same
time.
To turn on the power
PWR ON-OFF button — 3
When the power is off, press this button to
turn the power on.
To turn the power off, press this button for 2
seconds or longer.
To adjust the volume
Volume up button — 1
The volume will increase when this button is
pressed.
Volume down button — 2
The volume will decrease when this button is
pressed.
Mode selection
Press the mode change button (3) to select the desired mode.
The mode changes in the following order.
FM1 → FM2 → FM3 → MW → LW → CD
→ USB or iPod* → Bluetooth ®*
→ FM1
To listen to the radio
To select FM/MW/LW mode
Press the mode change button (3) to select the desired mode.
(AM/FM or LW/MW/FM)
Automatic radio tuning
Seek up button — 4/Seek down button — 5
After pressing these buttons, the reception of the selected station will begin.
To listen to a CD
To fast-forward/fast-reverse the
disc
To fast-forward or fast-reverse the disc, press
the fast-forward button (4) or the fast-reverse button (5).

Fast-forward button — 4
You can fast-forward the disc by pressing the
fast-forward button. While the button is kept
pressed, the disc will be fast-forwarded.

Fast-reverse button — 5
You can fast-reverse the disc by pressing the
fast-reverse button. While the button is kept pressed, the disc will be fast-reversed.NOTEl In the case of an MP3 CD, you can fast-for-
ward and fast-reverse tracks in the same
folder.
To select a desired track
Track up button — 4
Press the button repeatedly until the desired track number appears on the display.

Track down button — 5
Press the button repeatedly until the desired track number appears on the display.
To listen to an iPod
Press the mode change button (3) and select
iPod mode.
To select a desired track
Track up button — 4
Press the button repeatedly until the desired track number appears on the display.
Steering wheel remote control switch (audio system type 1) *
7-45OKTE15E3For pleasant driving7

NOTElThe track number increases continuously
while the button is pressed.
Track down button — 5
Press the button repeatedly until the desired track number appears on the display.
NOTEl The track number decreases continuously
while the button is pressed.
To listen to a USB memory de-
vice
Press the mode change button (3) and select
USB mode.
To select a desired file
File up button — 4
Press the button repeatedly until the desired
track number appears on the display.
NOTEl The track number increases continuously
while the button is pressed.
File down button — 5
Press the button repeatedly until the desired track number appears on the display.
NOTEl The track number decreases continuously
while the button is pressed.
Steering wheel remote control switch (audio system type 1) *
7-46OKTE15E3For pleasant driving7

6.The voice guide will say “Calling
” and then the sys-
tem will dial the telephone number.NOTEl When the confirmation function is on, the
system will ask if the name and location of the receiver are correct.
If the name is correct, answer “Yes.”
To change the name or location to call, an- swer “No.” The system will return to Step 3.
Redialing
You can redial the last number called, based
on the history of dialed calls in the paired cel-
lular phone.
Use the following procedure to redial. 1. Press the SPEECH button.
2. Say “Redial.”
SEND function
E00761300035
During a call, press the SPEECH button to
enter voice recognition mode, then say “ SEND” to generate DTMF tones.
For example, if during a call you need to sim- ulate the press of a phone button as a re-
sponse to an automated system, press the SPEECH button and speak “1 2 3 4 pound SEND” and the 1234# will be sent on your
cellular phone.
Receiving calls
E00761600012
If an incoming phone call is received while
the ignition switch is in the “ACC” or “ON”
position, the audio system will be automati- cally turned on and switched to the incomingcall, even when the audio system was origi-
nally off.
The voice guide announcement for the in- coming call will be output from the front pas- senger’s seat speaker.
If the CD player or radio was playing when
the incoming call was received, the audio
system will mute the sound from the CD player or radio and output only the incomingcall.
To receive the call, press the PICK-UP but- ton on the steering wheel control switch.
When the call is over, the audio system will
return to its previous state.
MUTE function
E00760300041
At any time during a call, you can mute the
vehicle microphone.
Pressing the SPEECH button and then saying
“Mute” during a call will turn ON the MUTE
function and mute the microphone.
Saying “Mute off” in the same way will turn off the MUTE function and cancel the muteon the microphone.
Switching between hands-free
mode and private mode
E00761400036
The Bluetooth ®
2.0 interface can switch be-
tween Hands-free mode (Hands-free calls) and private mode (calls using cellular phone).If you press the SPEECH button and say “Transfer call” during a Hands-free call, you
can stop the Hands-free mode and talk in pri-
vate mode.
To return to Hands-free mode, press the SPEECH button again and say “Transfer
call”.
Phone book function
E00763700017
The Bluetooth ®
2.0 interface has 2 types of
unique phone books that are different from
the phone book stored in the cellular phone. They are the vehicle phone book and the mo-
bile phone book.
These phone books are used to register tele- phone numbers and to make calls to desired
numbers via the voice recognition function.
NOTEl Disconnecting the battery cable will not de-
lete information registered in the phone
book.
Bluetooth ®
2.0 interface
7-96OKTE15E3For pleasant driving7

If the vehicle breaks down.................................................................. 8-02Emergency starting............................................................................. 8-02
Engine overheating............................................................................. 8-04
Bleeding the fuel system..................................................................... 8-05 Removal of water from the fuel filter................................................. 8-06
Tools, jack and jack handle................................................................. 8-07 Jacking up the vehicle......................................................................... 8-13
Spare wheel......................................................................................... 8-17
How to change a tyre.......................................................................... 8-18
Towing................................................................................................ 8-22
Operation under adverse driving conditions....................................... 8-25For emergencies
OKTE15E38

WARNINGlBe sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.NOTEl The chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if needed.
l If chocks are not available, use stones or any
other objects that are large enough to hold the wheel in position.
6. Get the spare wheel, jack and jack han-
dle ready.
7. Place the jack under one of the jacking
points shown in the illustration. Use the jacking point closest to the tyre you wish
to change.
2WD vehicles with 15 inch wheelsC-Front jacking point (2WD vehicles with
15 inch wheels)2WD vehicles with 16 inch wheels and
4WD vehiclesD-Front jacking point (2WD vehicles 16
inch wheels and 4WD vehicles)E-Rear jacking point
Jacking up the vehicle
8-14OKTE15E3For emergencies8

2.Using the jack handle, turn the release
valve anticlockwise slowly to lower theram and remove the jack.
3. Press the piston down all the way, and
turn the release valve clockwise as far as possible.
4. Store jack, jack handle and chocks.
WARNINGl Be sure to open the release valve slowly. If
it is opened quickly, the vehicle will drop
abruptly and the jack may come out of position, causing a serious accident.CAUTIONl If the release valve is loosened too much (2
or more turns) in the anticlockwise direction, the jack’s oil will leak and the jack cannot
be used.CAUTIONl Close the release valve slowly when lower-
ing the vehicle, or the valve may be dam-
aged.NOTEl Occasionally when the vehicle is jacked up,
the grooved portion of the designated pointwill not come off. When this happens, rock
the vehicle to lower the ram.
l If the jack is difficult to remove by hand, in-
sert the jack handle (L) into the bracket (M).
Then using the handle, remove the jack.WARNINGl Stop jacking up the vehicle as soon as the
tyre is raised off the ground. It is danger-
ous to raise the vehicle any higher.WARNINGl Do not get under your vehicle while using
the jack.
l Do not bump the raised vehicle or leave it
sitting on the jack for a long time. Both
are very dangerous.
l Do not use a jack except the one that
came with your vehicle.
l The jack should not be used for any pur-
pose other than to change a tyre.
l No one should be in your vehicle when us-
ing the jack.
l Do not start or run the engine while your
vehicle is on the jack.
l Do not turn the raised wheel. The tyres
still on the ground could turn and make your vehicle fall off the jack.
Jacking up the vehicle
8-16OKTE15E3For emergencies8

4.Insert the wheel nut wrench (E) through
the end of the jack handle hole (F), and
then turn it anticlockwise to lower the spare wheel completely to the ground
and to slack the chain.
5. Remove the hanger disc (G) from the
spare wheel.
To install
1. Install the hanger disc (A) in the wheel
disc hole.
2. Turn the wheel nut wrench (B) clock-
wise to wind up the chain.
NOTEl Confirm that the hanger disc is securely fit-
ted in the wheel disc hole when the wheel isjust lifted off the ground.
3. After winding up the spare wheel suffi-
ciently, make sure it is not loose (the tightening torque should be approxi-
mately 40 Nm) then withdraw the jack
handle, taking care not to turn it in the
reverse direction.
CAUTIONl The spare wheel should always be securely
in position.
If a flat tyre is changed, put the flat tyre in
the spare wheel mounting position with the wheel outer surface upward, and use the wheel nut wrench to secure it firmly.How to change a tyre
E00801202653
Before changing a tyre, first stop your vehi-cle in a safe, flat location. 1. Park the vehicle on level and stable
ground.
2. Set the parking brake firmly.
How to change a tyre
8-18OKTE15E3For emergencies8

3.On vehicles with manual transmission,
turn the ignition key to the “LOCK” po-
sition, move the gearshift lever to the “R” (Reverse) position.
On vehicles with automatic transmis- sion, move the selector lever to the “P” (PARK) position, turn the ignition key to
the “LOCK” position.
4. Turn on the hazard warning flashers and
set up a warning triangle, flashing signal lamp, etc., at an adequate distance from
the vehicle, and have all your passengers
leave the vehicle.
5. To prevent the vehicle from rolling
when it is raised on the jack, place
chocks or blocks (A) at the tyre that is diagonally opposite from the tyre (B)
you are changing.WARNINGl Be sure to apply chocks or blocks to the
correct tyre when jacking up the vehicle.If the vehicle moves while jacked up, the
jack could slip out of position, leading to
an accident.NOTEl The chocks shown in the illustration do not
come with your vehicle. It is recommended
that you keep one in the vehicle for use if needed.
l If chocks are not available, use stones or any
other objects that are large enough to hold the wheel in position.
6. Get the spare wheel, jack, jack handle
and wheel nut wrench ready.
NOTEl Put the spare wheel under the vehicle body
near the flat tyre. This makes it safer if the jack slips out of position.
7. Loosen the wheel nuts with the wheel
nut wrench. Do not remove the wheel nuts yet.
Five wheel nutsSix wheel nuts
How to change a tyre
8-19OKTE15E3For emergencies8