2015 MITSUBISHI L200 low beam

Indication and warning lampsE005015035331. CRUISE indication lamp* ® p. 6-51
2. Turn-signal indication lamps/Hazard warning indication lamps ® p. 5-07
3. High-beam indication lamp ® p. 5-07
4. Front fog lamp indication lamp* ® p. 5-07
5. Rear fog lamp indication lamp ® p. 5-07
6. Seat belt reminder/warning lamp ® p. 4-11
7. Low fuel warning lamp ® p. 5-05
8. 2WD/4WD operation indication lamp* ® p. 6-27, 6-329. Rear differential lock indication lamp*
® p. 6-35
10. Check engine warning lamp ® p. 5-08
11. Diesel preheat indication lamp ® p. 5-07
12. Oil pressure warning lamp ® p. 5-09
13. Fuel filter indication lamp ® p. 5-08
14. Charge warning lamp ® p. 5-09
15. A/T (automatic transmission) fluid tem- perature warning lamp (vehicles with
A/T) ® p. 6-23
16. Selector lever position indicator (vehi- cles with A/T) ® p. 6-2017. Diesel particulate filter (DPF) warning
lamp* ® p. 6-15
18. Brake warning lamp ® p. 5-08
19. Active Stability & Traction Control (ASTC) OFF indication lamp*
® p. 6-49
20. Anti-lock brake system (ABS) warning lamp* ® p. 6-46
21. Active Stability & Traction Control (ASTC) indication lamp* ® p. 6-49
22- Door ajar warning lamp ® p. 5-10
23. Supplemental restraint system (SRS) warning lamp* ® p. 4-40
Indication and warning lamps
5-06OKTE15E3Instruments and controls5Type 1Type 2

Indication lampsE00501600012Turn-signal indication lamps/
Hazard warning indication lamps
E00501700185
These indication lamps blink
on and off when a turn-sig-
nal lamp is operating.
NOTEl If the blinking is too fast, the cause may be a
blown lamp bulb or a faulty turn-signal con-
nection.
When the hazard warning lamp switch is
pressed, all turn-signal lamps will flash on and off continuously.
High-beam indication lamp
E00501800115
This indication lamp illumi-
nates when the high-beam is used.
Front fog lamp indication
lamp*
E00501900347
This indication lamp illumi-
nates while the front fog
lamps are on.
Rear fog lamp indication lamp
E00502000114
This indication lamp illumi-
nates while the rear fog lamp is on.
Diesel preheat indication lamp
E00502300250
This indication lamp illumi-
nates when the ignition switch is placed in the “ON”
position. As the glow plug becomes hot, the lamp goes
out and the engine can be
started.
CAUTIONl If the diesel preheat indication lamp comes
on after the engine is started, the engine speed may not rise above the idling speedbecause of fuel freezing. In this case, keep
the engine idling for about ten minutes, then turn off the ignition switch and immediately
turn it on again to confirm that the diesel
preheat indication lamp is off.NOTEl If the engine is cold, the diesel preheat indi-
cation lamp is on for a longer time.
l When the engine has not been started within
about 5 seconds after the diesel preheat indi- cation lamp went out, return the ignition
switch to the “LOCK” position. Then, turn
the switch to the “ON” position to preheat the engine again.
l When the engine is warm, the diesel preheat
indication lamp does not come on even if the
ignition switch is placed in the “ON” posi-
tion.
Indication lamps
5-07OKTE15E3Instruments and controls5

NOTElIf the lamps do not turn on or off with the
switch in the “AUTO” position, manually
operate the switch and we recommend you
to have your vehicle checked.
[Vehicles with Daytime Run-
ning Lamp]
When the ignition switch is in the “ON” posi- tion and the lamp switch is set to the “OFF”
position, the low beam of the headlamps, tail lamps, etc., will illuminate.
Lamps (headlamps, fog lamps, etc.) auto-cutout function
l If the ignition key is turned to “LOCK”
or “ACC” position or removed from the
ignition switch and the lamps will stay on for about 3 minutes without opening the driver’s door while the lamp switch
in the “
” position, the lamps automat-
ically turn off.
l If the ignition key is turned to “LOCK”
or “ACC” position or removed from the ignition switch and the driver’s door is opened within 3 minutes while the lamp
switch in the “
” position, a buzzer
will sound to warn the driver that the
lamps have not been turned off, and
these lamps will automatically turn off.
NOTEl The lamp auto-cutout will not function when
the lamp switch is in the “” position.
l When the ignition key has been turned either
to the “LOCK” or “ACC” position or re- moved from the ignition switch with the
lamp switch in the “
” position, and the
lamp switch is returned to the “OFF” posi- tion within approximately 3 minutes, the au-
to-cutout function will not be activated.
When you want to keep the
lamps on
l Turn the lamp switch in the “OFF” posi-
tion to switch off all lamps while the ig-
nition key is in the “LOCK” or “ACC” position or remove it from the ignitionswitch.
l Turn on the lamps with the switch in the
“
” or “” position again, then the
lamps will remain on.
NOTEl It is possible to alter the auto-cutout function
such that:
• Auto-cutout function is never activated.
For details, we recommend you to consult a
MITSUBISHI MOTORS Authorized Serv-
ice Point.Lamp monitor buzzer
E00506100184
If the driver’s door is opened when the igni-
tion key is in the “LOCK” or “ACC” position or removed from the ignition switch while
the lamps are on, a buzzer will sound to re-
mind the driver to turn off the lamps. When
the lamp auto-cutout function acts, the buzzer
will stop automatically. When this function does not act, turn off the lamp switch to stop
the buzzer.
Dipper (High/Low beam
change)
E00506200286
When the lamp switch is in the “” posi-
tion, the beam changes from high to low (or
low to high) each time the lever is pulled to (1). While the high-beam is on, the high-
beam indication lamp in the instrument clus-
ter will also illuminate.
Combination headlamps and dipper switch
5-34OKTE15E3Instruments and controls5

Headlamp flasher
E00506300157
The high-beams flash when the lever is
pulled slightly (2), and will go off when it is released.
When the high-beam is on, the high-beam in-
dication lamp in the instrument cluster will
also illuminate.NOTEl The high-beams can also flash when the
lamp switch is in the “OFF” position.
l If you turn the lamps off with the headlamps
set to high-beam illumination, the headlamps
are automatically returned to their low-beam setting when the lamp switch is next turned
to the “
” position.
Headlamp levelling switch*
E00506400826
The angle of the headlamp beam varies de-pending on the load carried by the vehicle.
The headlamp levelling switch can be used to
adjust the headlamp illumination distance (when the lower beam is illuminated) so that the headlamps’ glare does not distract otherdrivers.
Set the switch (referring to the following ta-
ble) to the appropriate position according to
the number of people and the load in the ve- hicle.CAUTIONl Always perform adjustments before driving.
Do not attempt to adjust while driving, as it could cause an accident.NOTEl When adjusting the beam position, first put
the dial in the “0” position (the highest beamposition).Single cabVehicle con-
ditionSwitch posi- tion“0”“2”●:1 person:Full luggage loadingSwitch position 0-Driver onlySwitch position 2-Driver + Full luggageloading
Club cab
Vehicle con- ditionSwitch posi- tion“0”“3” or“4”●:1 person:Full luggage loadingSwitch position 0-Driver only
Headlamp levelling switch*
5-35OKTE15E3Instruments and controls5

NOTElThe front fog lamps are automatically turned
off when the headlamps or tail lamps are turned off. To turn the front fog lamps on again, turn the knob in the “ON” directionafter turning on the headlamps or tail lamps.
l Do not use fog lamps except in conditions of
fog, otherwise excessive lamp glare maytemporarily blind oncoming vehicle drivers.
l In case of vehicles with Daytime Running
Lamp, the front fog lamp can be operated even if the lamp switch is set to the “OFF”
position, because the low beam of the head- lamps, tail lamps, etc. illuminate when the
ignition key is at the “ON” position.Rear fog lamp switch
E00506900313
The rear fog lamp illuminates only when theheadlamps or front fog lamps (if so equipped)
are on.
An indication lamp in the instrument cluster
comes on when the rear fog lamp is turned on.

[Vehicles without front fog lamps]
Turn the knob once in the “ON” direction to
turn on the rear fog lamp. To turn the rear fog
lamp off, turn the knob once in the “OFF” di- rection. The knob will automatically return to
its original position when you release it.

[Vehicles with front fog lamps]
Turn the knob once in the “ON” direction to turn on the front fog lamps. Turn the knob
once more in the “ON” direction to turn on the rear fog lamp. To turn the rear fog lamp
off, turn the knob once in the “OFF” direc- tion. Turn the knob once more in the “OFF” direction to turn off the front fog lamps. The
knob will automatically return to its original
position when you release it.NOTEl The rear fog lamp is automatically turned off
when the headlamps and front fog lamps (if
so equipped) turned off.
l To turn the rear fog lamp on again, turn the
knob once in the “ON” direction after turn-ing on the headlamps. (Vehicles without
front fog lamps)NOTEl To turn the rear fog lamp on again, turn the
knob twice in the “ON” direction after turn-ing on the headlamps. (Vehicles with front
fog lamps)
l In case of vehicles with Daytime Running
Lamp, the rear fog lamp can be operated
even if the lamp switch is set to the “OFF”
position, because the low beam of the head- lamps, tail lamps, etc. illuminate when the ignition key is at the “ON” position.Wiper and washer switch
E00507101191CAUTIONlIf the washer is used in cold weather, the
washer fluid sprayed against the glass may
freeze, which may hinder visibility. Warm the glass with the defroster or rear window
demister before using the washer.Windscreen wipers
E00516900303
Except for vehicles equipped
with rain sensor
The windscreen wipers can be operated with the ignition switch in the “ON” or “ACC”
position.
Rear fog lamp switch
5-38OKTE15E3Instruments and controls5

Ignition switchE00601402044
M/TA/T
LOCK
The engine is stopped and the steering wheel
locked. The key can only be inserted and re- moved when the switch is in this position.
ACC
The engine is stopped, but the electrical devi- ces such as the radio and cigarette lighter can
be operated.
ON
The engine is running, and all the vehicle’selectrical devices can be operated.
START
The starter motor operates. After the engine
has started, release the key and it will auto-
matically return to the “ON” position.
NOTEl If your vehicle is equipped with the Daytime
Running Lamp, when the ignition switch is
in the “ON”, the headlamp low beams etc. are turned on.
Refer to “Headlamps” on page 5-32.
l Your vehicle is equipped with an electronic
immobilizer.
To start the engine, the ID code which the transponder inside the key sends must match
the one registered in the immobilizer com- puter.
Refer to “Electronic immobilizer” on page 3-02.To remove the key
For vehicles with a M/T, when removing the
key, push the key in at the “ACC” position
and keep it depressed until it is turned to the “LOCK” position, and remove it.
For vehicles with an A/T, when removing the
key, first set the selector lever to the “P”
(PARK) position, and then turn the key to the “LOCK” position, and remove it.
Ignition switch
6-12OKTE15E3Starting and driving6

Engine compartment fuse loca-tion table
E01008000583
Engine compartment fuse locationFront
No .SymbolElectrical system
Ca-
paci- ty1———2Electric window sys-
tem40 ANo .SymbolElectrical system
Ca-
paci- ty3Ignition switch40 A4Air conditioning com-
pressor10 A5Condenser fan motor20 A6Headlamp high-beam
(left)10 A7Headlamp high-beam
(right)10 A8Headlamp low beam
(left)10 A9Headlamp low beam
(right)10 A10Engine control20 A11Alternator7.5 A12Stop lamps15 A13Horn10 A14Automatic transmis-
sion20 A15Hazard warning flash-
er10 A16Fuel pump15 ANo .SymbolElectrical system
Ca-
paci- ty17Front fog lamps15 A18Audio amp20 A
l Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
l The table above shows the main equip-
ment corresponding to each fuse.
Identification of fuse
E01008100308
CapacityColour7.5 ABrown10 ARed15 ABlue20 AYellow30 AGreen (fuse type)/
Pink (fusible link type)40 AGreen (fusible link type)Fuse replacement
E01007800656
1. Before replacing a fuse, always turn off
the electrical circuit concerned and place
the ignition switch in the “LOCK” posi-
tion.
Fuses
10-23OKTE15E3Maintenance10

Replacement of lamp bulbsE01003100710
Before replacing a bulb, ensure the lamp is off. Do not touch the glass part of the new
bulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.CAUTIONl Bulbs are extremely hot immediately after
being turned off.
When replacing a bulb, wait for it to cool sufficiently before touching it. You couldotherwise be burnt.NOTEl If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
l Be careful not to scratch the vehicle body
when removing a lamp or lens.
l When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem. When the lamp is switched on, the heat
will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to have the lamp checked.Bulb capacity
E01003200085
When replacing a bulb, use a new bulb with
the same wattage and colour.
Outside
E01003304169
Front
1- Headlamps, high-beam: 60 W (HB3)2- Headlamps, low beam: 55 W (H11)
3- Front turn-signal lamps: 21 W (PY21W)
4- Position lamps: 5 W (W5W)
5- Front fog lamps*: 55 W (H11)
6- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
7- Side turn-signal lamps (on outside rear-
view mirror)*Type 2
1- Headlamps, high/low beam: 60/55 W
(H4)
2- Position lamps: 5 W (W5W)
3- Front turn-signal lamps: 21 W (PY21W) 4- Front fog lamps*: 55 W (H11)
5- Side turn-signal lamps (on fender)*: 5 W
(WY5W)
6- Side turn-signal lamps (on outside rear-
view mirror)*

Codes in parentheses indicate bulb types.
Replacement of lamp bulbs
10-25OKTE15E3Maintenance10 Type 1