2015 MITSUBISHI L200 clock reset

Resetting the elevation
Press the “RESET” function button to reset
the elevation plotted in graph.
NOTEl Pressing the “RESET” function button will
not reset the indication (C).
l It is possible to set the display unit to m or
ft.
Refer to “User customization” on page 5-27.Barometer
E00518700044
This display shows the atmospheric pressure
at the present location in (A). The atmospher- ic pressure values are graphed every5 minutes and the data for up to 4 hours are
shown in (B).
Resetting the atmospheric pressure
Press the “RESET” function button to reset
the atmospheric pressure plotted in graph.
NOTEl Pressing the “RESET” function button will
not reset the indication (C).
l It is possible to set the display unit to hPa,
mb, kPa, or inHg.
Refer to “User customization” on page 5-27.Calendar
E00518800032
The date is shown. The calendar pattern can
be changed to your desired setting.
Refer to “Changing the calendar setting” on page 5-24.
Clock-only
E00518900033
Only the clock is shown. The time notation
can be changed to your desired setting. (12 hour/24 hour)
Centre information display*
5-18OKTE15E3Instruments and controls5

Changing the clock settings
E00519200121
1. Press the “ADJ” button to select the
clock setting display.
2. It is possible to adjust the clock using
the function buttons.
“H”-Adjust “hour”.
The indication increases by one
hour, every time you lightly press the “H” function button. If you con-tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the hour selected.“M”-Adjust “minute”.
The indication increases by one mi-
nute, every time you lightly press
the “M” function button. If you con- tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the minute selected.“SET”
-To reset the minutes to zero.
The time is adjusted as described be-
low by pressing the function button
“SET”.
l 10:30-11:29 · · · · change to
11:00
l 11:30-12:29 · · · · change to
12:00
In this occasion, the display flashes twice and then the setting is changed.
Centre information display*
5-20OKTE15E3Instruments and controls5

15- Display
RDS uses PI (program identification) signal and AF (alternative frequency) list transmitted in addition to the normal FM broadcasting programs, and picks up the FM stations that are transmitting the same program from the AF list and automatically tunes to the station with the strongestsignal intensity.
Therefore, you can continue listening to one program in, for example, a long distance driving without retuning to the other station transmitting
the same program when you are leaving the service area of the currently receiving station.
The RDS radio also features the limited reception of the program types, the break-in reception of the traffic announcement to the EON (enhanced
other network) and emergency broadcast, and the limited/unlimited reception of the regional programs.
AF (Alternative Frequencies)
function
E00720900061
The AF function finds a station broadcasting
the same program and selects the station with the strongest signal of AF lists.
The AF function is turned on (with the AF in- dicator (12) shown on the display) at all times unless you manually switch it off.

The AF function can be turned ON and OFF.
Refer to “Function setup mode” on page
7-24.
CT (Clock Time) function
E00721000131
The clock can be set automatically by using
the signal from the local RDS stations. Refer to “Adjusting the time” on page 5-12.
REG (Regional) function
E00721100057
REG function limits to receive the stations
broadcasting regional programs.
Regional programming and regional net- works are organized differently depending on
the country or area (they may be changed ac- cording to the hour, state, or broadcast area),
so if you don’t want to receive the regional
programs automatically, you can set up REG
ON not to receive regional programs.

The REG function can be turned ON and OFF.
Refer to “Function setup mode” on page
7-24.
PI (Program Identification)
search function
E00721200221
When travelling long distance and the recal-
led preset station is weak, the radio searches
another frequency broadcasting the same pro- gramming with the same PI code in AF list.
If there are no frequencies broadcasting the
same programming, the radio searches a fre-
quency broadcasting the regional program-
ming. The radio succeeds in searching the re- gional programming, then the display shows the REG indicator (11).
If the radio does not succeed in searching the
regional programming, the radio returns to
the recalled preset station.
The PI function can be turned ON and OFF.
Refer to “Function setup mode” on page
7-24.LW/MW/FM electronic tuning radio with CD player (audio system type 1) *
7-21OKTE15E3For pleasant driving7

NOTElThis switches in the order FM1, FM2, FM3,
DAB1*, DAB2*, DAB3*, MW, and LW. *:When a DAB tuner is connected.
Manual/Seek Station Selection
Turn the /SEL key to the frequency to lis-
ten to.
/SEL key
(counter-
clockwise)Reduces the frequency being
received./SEL key
(clockwise)Increases the frequency be-
ing received. key
(hold down)Release the button to start
seek station selection, and
when a station is received,
scanning stops. key
(hold down)
Preset Memory
Register the broadcast station in advance, and select this at a later time.
1. Tune in to the frequency to register.
2. Hold down any of the keys from the
1RPT key to the 6
key.

A “Beep” sounds, and the preset key is registered.NOTEl The preset memory can register a maximum
of 6 stations for each band (FM1, FM2,
FM3).
l If a preset key that already has a station reg-
istered is selected, then this is overwritten with the new preset.
l Pressing the preset key will select the previ-
ously registered frequency.
Auto Memory (Auto Store)
The top 6 stations with a strong signal can be
automatically registered in order with preset keys.
Hold down the RADIO key.

After completion of auto store operations, the
product will receive the station registered in
the preset key [1].
CAUTIONl Please be aware that the formerly-registered
frequency in the memory will be overwrit- ten.NOTEl Using auto store for FM1 and FM2 switches
to FM3.
PTY Search
Select PTY (program content), and automati-
cally scan for stations. 1. During FM reception, press the PTY/
SCAN key.
This switches to the PTY selection mode.
2. Turn the
/SEL key to select PTY.
The PTY (program content) indicator
will flash, and station selection will au- tomatically start. When a station is re-
ceived, the station name is displayed.
NOTEl This receives the station detected first.
l 10 seconds after reception, PTY search
mode will be cancelled.Listen to DAB (audio system
type 2) * E00739101024
This explains how to listen to DAB.
Listen to DAB (audio system type 2) *
7-64OKTE15E3For pleasant driving7

CAUTIONlWhen the cigarette lighter socket is used as a
power source for an electric appliance, be sure that the electric appliance operates at
12 V and has an electric capacity of 120 W or less. In addition, long use of the electricappliance without running the engine may
run down the battery.Accessory socket*
E00711601160
The accessory socket can be used while theignition switch is in the “ON” or “ACC” po-
sition.
Open the cap (A) to uncover the socket. Use it to plug in an electrical device.
Type 1Type 2
CAUTIONl When you connect an electrical device,
make sure it is rated at 12 V and its electrical
capacity does not exceed 120 W. Remember
that prolonged use of an electrical device with the engine off could run down the bat-
tery.
l When the accessory socket is not in use, be
sure to close the cap, because the socket might become clogged by foreign materialand be short-circuited.NOTEl Long use of the electric appliance without
running the engine may run down the bat-
tery.
Especially avoid using it with the cigarette lighter.Digital clock*
E00711700193
The digital clock indicates the time with the
ignition switch in either “ON” or “ACC” po- sition.
To set the time
Set the time by pressing the various buttons
as described below.
1- To adjust the hour
2- To adjust the minutes
3- To reset the minutes to zero

10:30 - 11:29...... Changes to 11:00
11:30 - 12:29...... Changes to 12:00
Accessory socket*
7-109OKTE15E3For pleasant driving7

NOTElIf the battery cables are disconnected during
repairs or for any other reason, reset the
clock to the correct time after they are recon-
nected.Interior lamps
E00712000917
1- Room lamp (Front)*Personal lamps*
2- Room lamp (Rear)*
3- Door courtesy lamps*
4- Centre console downlight
NOTEl If you leave the lamps on without running
the engine, you will run down the battery.
Before you leave the vehicle, make sure that
all the lamps are off.Room lamps
E00712101289
1
(ON/
) -The lamp illuminates.Interior lamps
7-110OKTE15E3For pleasant driving7 Front* Rear (Type 1)* Rear (Type 2)*