2015 MITSUBISHI L200 buttons

1- Digital clock ® p. 5-20
Indicates the time.
2- Electronic compass This display shows the direction of the vehicle.
3- Frozen road warning ® p. 5-16
Gives an indication when the outside temperature is 3 °C or lower.
4- Outside temperature ® p. 5-16
5- Centre information display indications Indicates details of each display.
6- “INFO” button Used to select various kinds of information for display.
7- Function buttons Press this button to select options shown in the display.
8- “ADJ” button Used for adjusting the clock and for selecting settings displays.
9- Display for function buttons This display shows the options available for each function button.
Centre information display*
5-11OKTE15E3Instruments and controls5

Refer to “User customization” on page 5-27.Blank
E00519000015
The whole display can be turned into blank.
In this case, buttons remain illuminated.
NOTEl If you operate the audio system, the audio
display pops up.Selecting settings displays
E00519100090
Every time the “ADJ” button is pressed light-
ly, the display can be changed to the follow-ing:
CAUTIONl The driver should not operate the display
while the vehicle is in motion.
l When operating the system, stop the vehicle
in a safe area.
1- Changing the clock settings ® p. 5-20
2- Adjusting the display brightness ® p. 5-21
3- Correcting the compass ® p. 5-22
4- Changing the calendar setting ® p. 5-24
5- User customization ® p. 5-27
6- Adjusting the barometer ® p. 5-30
Centre information display*
5-19OKTE15E3Instruments and controls5 TA0024955

Changing the clock settings
E00519200121
1. Press the “ADJ” button to select the
clock setting display.
2. It is possible to adjust the clock using
the function buttons.
“H”-Adjust “hour”.
The indication increases by one
hour, every time you lightly press the “H” function button. If you con-tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the hour selected.“M”-Adjust “minute”.
The indication increases by one mi-
nute, every time you lightly press
the “M” function button. If you con- tinue pressing the button for about 2 seconds or more, the indication is fast-forwarded, and then the settingis changed to the minute selected.“SET”
-To reset the minutes to zero.
The time is adjusted as described be-
low by pressing the function button
“SET”.
l 10:30-11:29 · · · · change to
11:00
l 11:30-12:29 · · · · change to
12:00
In this occasion, the display flashes twice and then the setting is changed.
Centre information display*
5-20OKTE15E3Instruments and controls5

3.After making the adjustment, press the
“INFO” button to select the information display.Adjusting the display bright-
ness
E00519300034
The display brightness can be adjusted at 13
levels for both daytime and nighttime.
l BRIGHTNESS FOR DAY TIME
The display brightness is adjusted when the light switch is in the “OFF” position.
l BRIGHTNESS FOR NIGHT TIME
The display brightness is adjusted when the light switch is in the “
” or “”
position.
1. Press the “ADJ” button to show the
brightness adjusting display.
2. Press the “←” or “→” function button to
select the setting you wish to adjust (daytime or nighttime). Then press the
“SELECT” function button.
3. Use the function buttons to adjust the
brightness.
“+”-To make the display brighter
The display becomes brighter by one step, every time you lightly
press the “+” function button. If you
continue pressing the button for
about 2 seconds or more, the indica- tion is fast-forwarded.“-”-To make the display darker
The display becomes darker by one step, every time you lightly press the
“-” function button. If you continue pressing the button for about
2 seconds or more, the indication is fast-forwarded.“SET” -To set the brightness
Press function button “SET” to set
the new brightness. The display will flash twice.
Centre information display*
5-21OKTE15E3Instruments and controls5

Date setting
1.Press the “ADJ” button to select the cal-
endar setting display.
2. Press the “←” or “→” function button to
select “CALENDAR ADJUST”. Then press the “SELECT” function button.
3. Use the function buttons to set the calen-
dar.
“→”-Select “YEAR”, “MONTH”,
“DAY” you wish to change.
“YEAR”, “MONTH”, and “DAY”
are changed over by turns every time you lightly press the “→”
function button.“+”-Change “YEAR”, “MONTH”, “DAY” you have selected.
The indication is changed to your
desired date every time you lightly
press the “+” function button.
If you continue pressing the button
for about 2 seconds or more, the indication is forwarded.“SET”-Determine the date.
Press the “SET” function button.
Then the display flashes twice and the setting is changed.NOTEl The year changes in the following sequence:
2012 → 2013 → … 2099 → 2012 or 2013
→ 2014 → … 2099 → 2013.
l You can return to the previous display by
pressing the “BACK” function button.
4. After setting the date, press the “INFO”
button to return to the information dis- play.
Centre information display*
5-25OKTE15E3Instruments and controls5

2.Press the “←” or “→” function button to
select the “BAROMETER ADJUST” display. Then press the “SELECT” func-
tion button.
3. Adjust the barometer by pressing the
function buttons.
“+”-To adjust the barometer
Each gentle press of the
“+” function button will increase the
indicated barometer by 2 hPa. If you
continue pressing the button for
about 2 seconds or longer, the indi-
cation is fast-forwarded.“-”-To adjust the barometer
Each gentle press of the “-” function
button will decrease the indicated
barometer by 2 hPa. If you continue pressing the button for about 2 seconds or longer, the indication is
fast-forwarded.“SET”
-To set the barometer
Press the “SET” function button.
The display will flash twice, and the
new setting will be established.NOTEl You can return to the previous display by
pressing the “BACK” function button.4. After setting the barometer adjust, press
the “INFO” button to return to the infor-
mation display.
Resetting to the factory setting
1. Press the “ADJ” button to select the bar-
ometer adjustment display.
Press the “←” or “→” function button to select the “BAROMETER DEFAULT”display. Then press the “SELECT” func-
tion button.
Centre information display*
5-31OKTE15E3Instruments and controls5

1- PWR (On-Off) switch
2- Memory select buttons
3- TUNE/SEEK (Up-step/Up-seek) button
4- TUNE/SEEK (Down-step/Down-seek) button5- RADIO (FM/MW/LW selection) button
6- FM/MW/LW indicator
7- Preset memory number display
8- ST (Stereo) indicator*
9- Frequency display window

To listen to the radio
E00709000896
1. Press the PWR switch (1) to turn the au-
dio system ON and OFF. The system turns on in the last mode used.
2. Press the RADIO buttons (5) to select
the desired band.
3. Press the TUNE/SEEK button (3 or 4) to
tune to a station, or press one of the memory select buttons (2) to recall a sta-
tion memorised for that button.
To tune the radio
E00709100451
Automatic tuning
After keeping the TUNE/SEEK button (3 or 4) depressed, release the button, and the se-
lected station reception will start.
Manual tuning
The frequency changes every time the TUNE/SEEK button (3 or 4) is pressed. Press
the button to select the desired station.
To enter frequencies into the
memory
E00716101173
Manual setting
You can assign to the memory select buttons (2) a maximum of 18 stations in the FM band
(6 FM1, 6 FM2 and 6 FM3 stations) and 6 stations each in the MW and LW band. (Sta-
tions already assigned to the memory select buttons are replaced by any newly assigned stations.)
Follow the steps described below.
1. Press either the TUNE/SEEK button (3
or 4) to tune the frequency to be entered in the memory.
2. Press one of the memory select buttons
(2) for 2 seconds or longer.
The number of the button corresponding to the entry in the memory and the fre-
quency are displayed.
3. The preset memory setting is retrieved
by pressing the button and then releasing
it within 2 seconds.
Automatic setting
With the method, all manually set stations in
the band currently selected for reception are
replaced with stations in the same band that are automatically selected in order of signalstrength. The radio automatically selects 6
stations in the FM band (FM3 station only)
and 6 stations each in the MW and LW band.

Follow the steps described below.
LW/MW/FM electronic tuning radio with CD player (audio system type 1) *
7-19OKTE15E3For pleasant driving7

1. With the radio mode selected, hold downthe RADIO button (5) for 2 seconds orlonger. The 6 stations with the best sig-
nal strength will automatically be as- signed to the memory select buttons (2),
with the lowest-frequency station being
assigned to the lowest-number button.2. When you subsequently press a memory
select button to select a channel number,
the radio will begin receiving the station
assigned to that number.NOTEl If you press the RADIO button (5) for 2 sec-
onds or longer while tuning in the FM1 or
FM2 band, the radio will automatically switch to the FM3 band, where the automat-
ic seeking/storing will be activated.Radio data system (RDS)
E00709200452
1- PWR (On-Off) switch
2- Memory select buttons
3- TUNE/SEEK (Down-step/Down-seek) button
4- TUNE/SEEK (Up-step/Up-seek) button5- RADIO (FM/MW/LW selection) button 6- TP (Traffic program) button
7- PTY (Program type) button
8- MENU button
9- RDS (Radio data system) indicator10- PTY (Program type) indicator
11- REG (Regional program) indicator 12- AF (Alternative Frequencies) indicator
13- TP (Traffic program identification) indi- cator
14- CT (Clock time) indicator
LW/MW/FM electronic tuning radio with CD player (audio system type 1) *
7-20OKTE15E3For pleasant driving7