2015 MITSUBISHI iMiEV maintenance

Replacement of light bulbs
Vehicle care and maintenance 9-27
9
2. Turn the socket (C) counterclockwise to remove it. 3. Pull the bulb out of the socket.4. To install the bulb, perform the removal steps in reverse.
N00943900128
1. Remove the mounti
ng screws (A) and
remove the light unit. 2. While holding down the tab (B), pull out the connector.
3. Remove the screws (C) and then remove the bulb holder. 4. Pull the bulb out of the socket.5. To install the bulb, perform the removal steps in reverse.
High-mounted stop light
BK0209800US.book 27 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Vehicle care precautions 9-28 Vehicle care and maintenance
9
N00944001413
1. When removing the light unit (A), push it toward the left side
of the vehicle body.
2. Use a flat blade screwdriver into the tab (B) and pry gently to remove the lens. 3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal steps in reverse.
N00945100195
In order to maintain the value of your vehicle, perform regular maintenance using the proper materials and procedures
. Be sure to use only
those materials and proc
edures that meet your
local environmental pollution control regula- tions. Choose the material
s you will use care-
fully, to be sure that they do not contain corrosives. If you are not sure, contact a certi- fied i-MiEV dealer for help in choosing thesematerials.
License plate lights
NOTE
 When installing the light, insert tab (C) first then align and insert tab (D).
Vehicle care precautions
BK0209800US.book 28 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Cleaning the inside of your vehicle
Vehicle care and maintenance 9-29
9
These can all be danger
ous, and they all can
damage your vehicle.
N00945200079
After washing the inside of your vehicle withany cleaner, wipe it dry
in a shady, well venti-
lated area.
N00945300214
1. Lightly wipe these off with a soft clothsoaked in a mild soap and water solution. 2. Dip cloth in fresh water and wring out well. Using this cloth,
wipe off the deter-
gent thoroughly.
N00945500144
1. To maintain the value of your new vehi-cle, maintain the upholstery carefully andkeep the interior clean. Use a vacuum cleaner
and brush to clean
the seats. If stained,
vinyl and synthetic
leather should be clea
ned with an appro-
priate cleaner. Cloth fabrics can be cleaned with either
upholstery cleaner or a
mild soap and water solution. 2. Clean the carpeting with a vacuum cleaner and remove a
ny stains with carpet
cleaner. Oil and grea
se can be removed by
lightly dabbing with
a clean white cloth
and spot remover.
CAUTION Cleaning products can
be dangerous. Some
are poisonous. Others
are highly flammable.
Some are dangerous if you breathe theirfumes in a closed space. When you use any- thing in a container to clean your vehicle, be sure to follow the in
structions. Always open
your vehicle doors or windows when you’re cleaning the inside. Never use the following chemicals to clean your vehicle:• Gasoline• Carbon Tetrachloride• Benzine• Kerosene• Naphtha• Acetone• Turpentine• Paint Thinner• Lacquer Thinner• Nail Polish Remover
Cleaning the inside of your vehicle
CAUTION Do not use organic substances (solvents, benzine, kerosene, alc
ohol, gasoline, etc.) or
alkaline or acidic solutions.These chemicals can cause discoloring, staining or cracking of the surface. If you use cleaners or
polishing agents, make
sure their ingredients do not include the sub- stances mentioned above.NOTE
 Always read the instru
ctions on the cleaner
label.
Plastic, vinyl leather, fabric and flocked parts
NOTE
 Do not use cleaners,
conditioners, and pro-
tectants containing
silicones or wax.
Such products, when applied to the instru-ment panels or other pa
rts, may cause reflec-
tions on the windshiel
d and obscure vision.
Also, if such products
get on the switches of
the electrical accessories, it may lead to fail- ure of these accessories.
Upholstery
NOTE
 If fuzzing is difficult to remove from the seat upholstery, draw a suitable defuzzing brush over the surface in
one direction.
BK0209800US.book 29 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Cleaning the outside of your vehicle 9-30 Vehicle care and maintenance
9
N00945600275
1. To clean, lightly wipe the leather with a soft cloth soaked in a mild soap and water solution.2. To rinse, dip the cloth in fresh water, wring it out well, a
nd wipe off all the
soap. 3. To preserve and prot
ect, use a leather pro-
tecting agent on the genuine leather sur- face.
N00945700061
To protect your vehicle’s finish, wash it often and thoroughly. If desired, you may wax your vehicle using a nonabrasi
ve automobile wax.
N00945800046
Industrial pollution, road tar, bird droppings, tree sap, insect remain
s, sea water and other
foreign matters can da
mage the finish on your
vehicle.Generally, the longer
any foreign material
stays on the finish, the worse the damage. Wash your vehicle as soon as possible when-ever the finish gets soiled.
N00945900627
Chemicals contained in the dirt and dustpicked up from air, rain, snow or road sur- faces can damage the paint and body of your vehicle if left on.Frequent washing and wa
xing is the best way
to protect your vehicle from this damage. Do not wash the vehicl
e in direct sunlight.
Park the vehicle in the shade and spray it with water to remove dust.
Next, using plenty of
clean water and
a car washing mitt or sponge,
wash the vehicle from top to bottom.Use a mild car washing soap if necessary. Rinse thoroughly and wipe dry with a cham- ois or soft cloth. Af
ter washing
the vehicle,
carefully clean the joints and flanges of the doors, hood, etc., where dirt is likely to remain.
Genuine leather
(if so equipped)
NOTE
 If genuine leather is we
t with water, wipe it
with a dry, soft cloth. If left damp, mildew may grow.  The genuine leather su
rface can be damaged
if brushed with a nylon or synthetic fiber brush.  Organic solvents such as benzine, kerosene, alcohol, gasoline, acid or alkaline solventscan discolor the genuine leather surface and should not be used.  The genuine leather surface may harden and shrink if it is exposed to the direct sunlight for long hours. When your vehicle is parked,place it in the shade as much as possible.
Cleaning the outside of your vehicle Foreign material Wa s h i n g
WA R N I N G Do not wash the vehicle while charging the main drive lithium-ion battery. Doing so could cause a
fire or an
electric
shock. Before washing the vehicle, make sure that the charging lid and the inner lid arecompletely closed. If the lid is open, the charging unit is exposed to water, resulting in a fire or anelectric shock. Do not pour water inside the electric motor unit room. Doing so could cause a fire or an electric shock.CAUTION When washing the vehicle, turn the electric motor switch to the “LOCK” position. Do not use a high pressure washing machine to clean the underneath of the vehicle. Doing so might cause th
e electric motor unit
problem or malfunction.
BK0209800US.book 30 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Cleaning the outside of your vehicle Vehicle care and maintenance 9-31
9
Salt and other chemicals spread on winter roads in some geographical areas can have a detrimental effect on the vehicle underbody.You should flush the underbody with a high pressure hose every time you wash the out- side of your vehicle.Take special care to
remove mud or other
debris which could trap and hold salt and moisture. After washing your vehicle, wipe off all waterdrops from the rubber parts around thedoors to prevent the doors from freezing.
N00946000247
Wax your vehicle once or twice a year, orwhen water does not bead up on the paint.
Use a soft cloth to put a small amount of wax on the painted surfaces. After the wax hasdried, polish with a dry soft cloth. Do not wax your vehicle
in direct sunlight.
You should wax when the painted surfacesare cool.
N00946100059
If painted surfaces have been severely dam- aged and lost their original luster and color tone, polish the surface lightly with a finepolishing compound. Avoid limiting your polishing to the damage
d surface only; polish
a somewhat wider area, moving the polishing
 When washing the underside of your vehicle or the wheels, wear a pair of gloves to pro-tect your hands. Never spray or splash water on the electrical parts in under the hood. This may damagethem. Be careful also when washing the underbody. Do not spray water up under the hood. Avoid automatic car washers that use rotat- ing brushes. These brushes may scratch thepaint surface and make it dull. Scratches are more not
iceable on darker col-
ored vehicles. Some hot water wash
ing equipment uses
high pressure and heat to clean your vehicle.This heated water ma
y damage your vehi-
cle’s resin parts. It
can flood the interior of
the vehicle. Therefore, be sure of the follow-ing:• Keep the washing nozzle at least 28 inches(70 cm) away from the vehicle body.• When washing around the door glass, holdthe nozzle at a distance of more than 28 inches (70 cm) and at right angles to the glass surface.
 Make sure to do the following when using an automatic car wash, with help from eitherthis manual or the car wash operator, to avoid damaging your vehicle:• Fold the outside mirrors.• Remove the antenna.• Tape the wiper arm assembly.CAUTION
During cold weather
NOTE
 When the door is frozen, opening it by force may tear off or crack the rubber gasket installed around the door. Pour warm water to melt the ice. Be sure to thoroughly wipeoff the water after opening the door. To pre- vent freezing of the we
atherstripping on the
doors, hood, etc., treat with silicone lubri-cant.
Waxing
CAUTION Waxes containing high abrasive compounds should not be used. These waxes remove rustand stain effectively from the paintwork, but are harmful to the finish on the paint and the plate, because they also remove clearcoat.They are also harmful to other glossy sur- faces such as the grille, trim, moldings, etc. Do not use gasoline, kerosene, benzine or paint thinners to remove road tar or other dirt from the vehicle surface. Do not put wax on the areas having black matte coating because
it can cause uneven
discoloration, patches, bl
urs, etc. If these get
wax on them, wipe the wax off right away with a soft clot
h and warm water.
Polishing
BK0209800US.book 31 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Cleaning the outside of your vehicle 9-32 Vehicle care and maintenance
9
cloth in one direction.
After polishing, flush
the compound from the surface and apply acoat of wax to regain a beautiful luster.
N00946200089
Small cracks and scratches in the paint coatshould be touched up as soon as possible with touch-up paint to prevent corrosion. Check body areas facing the road or the tires carefully for damage to the paint caused by flying stones, etc. The
paint code number for
your vehicle can be found on the vehicle information code plate. Refer to “Vehicle information code plate” on page 11-2.
N00946300211
Use a sponge or chamois to clean these parts.If a vehicle wax sticks
to a gray or black
rough surface of the bumper, molding or lights, the surface may appear white in color. In this case, wipe it off using lukewarm waterand a soft cloth or chamois.
N00946400065
To prevent spots and corrosion of chromeparts, wash with water, dry thoroughly, andapply a nonabrasive automotive wax. If the chrome is severely damaged or pitted, use a commercially available chrome polish.
N00946500196
1. Remove dirt using a wet sponge.2. Use a mild detergent
on any dirt that can-
not be removed easily with water. Rinse off the detergent after washing thewheel.
3. Dry the wheel thoroughly using a chamois leather or a soft cloth.
N00946600067
The window glass can usually be cleanedusing only a sponge and
water. Glass cleaner
can be used to remove
wax, oil, grease, dead
insects, etc. After washing the glass, wipe it dry with a clean, dry, soft cloth.
N00946700097
Use a soft cloth and glass cleaner to removegrease, dead insects,
etc., from the wiper
blades.
Damaged paint Cleaning plastic parts
CAUTION Do not use a scrubbing brush or other rough scrubber as these may damage the plastic surface.
 Do not use wax containing compounds (pol- ishing powder) which
may damage the plas-
tic surface.  Do not let the plastic parts get soiled with gasoline, oil, brake fl
uids, greases, paint
thinner, and sulfuric
acid (battery electro-
lyte). These fluids, etc., may crack, stain or discolor the plastic parts.If any of these get on the plastic parts, wipe them up with a soft cloth or chamois and a mild solution of soap and water. Then rinsethem immediately with water.
Chrome parts Aluminum wheels (if so equipped)
CAUTION
CAUTION Do not use a brush or other hard implement on the wheels. Doing so could scratch the wheels. Do not use any cleaner th
at contains an abra-
sive substance or is ac
idic or alkaline. Doing
so could cause the coating on the wheels topeel or become disc
olored or stained.
Do not directly apply
hot water using a steam
cleaner or by any other means. Contact with seawater or road salt used for de-icing can cause corro
sion. Rinse off such
substances as s
oon as possible.
Window glass Wiper blades
BK0209800US.book 32 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Cleaning the outside of your vehicle Vehicle care and maintenance 9-33
9
Replace the wiper blades when they no longer clean the windshield and rear window prop-erly.
N00947000127
Never spray or splash
water on the electrical
components under the hood, as this may cause damage. Do not allow any nearby
parts (such
as plastic
parts) come into contact with sulphuric acid (12V starter battery electrolyte), which maycrack, stain, or discolour them. If this occurs, wipe the parts with a soft cloth saturated with a mild detergent and watersolution. Then immediately rinse the affected parts with plenty of water.Under the hood
BK0209800US.book 33 ページ ２０１４年１月１４日　火曜日　午前９時２６分

Alphabetical index 12-2
12
Cold
Cautions and actions to
deal with intense
cold
...............................................
3-9
Combination headlights and dimmer switch
..
5-44 Consumer information
........................
10-2
Coolant
.......................................
9-4
, 11-6
Cruising range
......................................
3-4
Cruising range indicator
.............
5-35
, 5-38
Cup holder
.........................................
5-55
D
Dash lights brightness indicator
..5-35
, 5-38
Daytime running lights
Bulb capacity
.................................
9-22
Replacement
..................................
9-24
Defogger (rear window)
......................
5-50
Dimensions
........................................
11-3
Dimmer (high/lo
w beam change)
.........
5-46
Dinghy towing
...................................
6-10
Disc brake pads
..................................
9-17
Dome light (Front
)/Reading lights
Bulb capacity
.................................
9-23
Switch
...........................................
5-52
Dome light (Rear)
Bulb capacity
.................................
9-23
Switch
...........................................
5-53
Door-ajar warning
light and buzzer
.......
5-43
Doors
Lock
...............................................
5-8
Power door locks
.............................
5-9
Driver’s seat belt
reminder/warning light
......
4-10 Driving during cold weather
..................
6-5
Driving, alcohol and drugs
....................
6-2
E
Economical driving
..............................
6-2
Electric motor
Number
..........................................
11-3
Specifications
.................................
11-5
Electric motor switch
...........................
5-18
Electric motor unit warning light
..........
5-43
Electric power steering system (EPS)
....
5-27
Electric rear window
defogger switch
....
5-50
Electronic immobilizer (Anti-theft starting system)
.............................................
5-2
Energy level gauge
..............................
5-40
Energy usage indicator
.........................
5-35
EV charging cable
...............................
3-21
F
Floor mat
.............................................
6-2
Fluid
Brake fluid
..............................
9-7
, 11-6
Coolant
...................................
9-4
, 11-6
Hot water heater fluid
..............
9-4
, 11-6
Washer fluid
...........................
9-7
, 11-6
Fluid capacities and lubricants
.............
11-6
Front fog lights
Bulb capacity
.................................
9-22
Indicator
........................................
5-42
Replacement
..................................
9-24
Switch
...........................................
5-47
Front seats
............................................
4-3
Front side-marker lights
Bulb capacity
.................................
9-22
Replacement
..................................
9-23
Front turn signal lights
Bulb capacity
.................................
9-22
Replacement
..................................
9-24
Fuses
.................................................
9-18
Fusible links
.......................................
9-18
G
Gauges
..............................................
5-34
General maintenance
...........................
9-17
General vehicle data
............................
11-3
Genuine parts
.......................................
3-7
Glove compartment
.............................
5-55
BK0209800US.book 2 ページ ２０１４年１月１４日　火曜日　午前９時２６分