When the HOLD function is activated, the trans-
mission is shifted automatically to position Pif:
R the driver's seat belt is not fastened and the
driver's door is open
R the engine is switched off, unless it is auto-
matically switched off by the ECO start/stop
function
The electric parking brake secures the vehicle
automatically if the HOLD function is activated,
the vehicle is stationary and:
R as ystem fault occurs
R the power supply is insufficient
If am alfunction occurs ,then the transmission
may also be shifted into position Pautomati-
cally.
Vehicles with manual transmission
The electric parking brake secures the vehicle
automatically if the HOLD function is activated
and:
R the driver's seat belt is not fastened and the
driver's door is open
R the engine is switched off, unless it is auto-
matically switched off by the ECO start/stop
function
R as ystem fault occurs
R the power supply is insufficient
The Brake immediately
Brake immediately message may also
appear in the multifunction display.
X Immediately depress the brake pedal firmly
until the warning message in the multifunc-
tion display goes out.
The HOLD function is deactivated.
Ah orn will sound at regular intervals if you turn
off the engine, take off your seat belt or open the driver's door when the HOLD function is activa-ted. The horn alerts you to the fact that the
HOLD function is still activated. If you attempt to
lock the vehicle, the toneb ecomes louder. The
vehicle cannot be locked until you have deacti-
vated the HOLD function.
i Oncey
ou have switched off the engine, you
cannot restart it until you have deactivated
the HOLD function. RACE START
Important safety notes i
RACE START must not be used on normal
roads. RACE START must only be activated
and used on dedicated road circuits, outside
of public road use.
i RACE START is only available in
Mercedes‑ AMG vehicles.
RACE START enables optimum acceleration
from astandin gstart .For this, asuitably high-
grip road surface is required, along with the
tyres and vehicle being in good condition. G
WARNING
If you use RACE START, individual tyres may
get into aspin and the vehicle could skid.
Dependin gonthe selected ESP ®
mode, there
is an increased risk of skidding and having an accident .Make sure that no persons ,animals
or obstacles are within range of the vehicle.
i Observe the safety notes on driving safety
systems (Y page 66).
Be sure to read the safety notes and informa-
tion on ESP ®
(Y page 71).
Activation conditions You can activat
eRACE START if:
R the doors are closed
R the engine is running and it has reached an
operating temperature of approximately
71 †. This is the case when the oil tempera-
ture gauge in the multifunction display is
shown in white.
R the drive program S,S+ orRace is selected
(Y page 154)
R the steerin gwheel is in the straight-ahead
position
R the vehicle is stationary and the brake pedal is
depressed (left foot)
R the transmission is in position D
Activating RACE START i
When manual mode (Y
page 163) is active,
the transmission automatically shifts up to
RACE START in the drive program. This func-
tion supports maximum acceleration with 194
Driving systemsDriving and parking
Display messages
Possible causes/consequences and
M
MSolutions Clutch overheated
Clutch overheated
Avoid pullin
gaway
Avoid pullin gaway
Engage/disengage Engage/disengage
clutch quickl yif
clutch quickl yif
req. req. The clutch is under considerable load and th
epermitte doperating
temperature has been exceeded .Awarning tone also sounds.
Avoid frequen tpullin gaway and drivin gatwalking pac eoverlonger
distances.
X Pull ove rand stop th evehicl esafely as soo naspossible, paying
attention to roa dand traffic conditions.
X Safeguar dthe vehicl eagainst rollin gaway (Y page 172).
X Leav ethe engin erunning.
The clutch is cooled mor equickl ywitht he engin erunning.
or
X If possible, continu edrivin gatas teady speed.
X Remove your foo tfro mt heclutch pedal and do no tallow th eclutch
to slip.
The clutch may also cool down during th ejou rney.
It may tak eseveral minute sfor it to cool down .Whent he clutch has
cooled down ,the display message disappears. The clutch is fully
operational again. N The boot lid is open.
X Clos ethe boot lid. M The bonne
tisopen.Aw arning tone also sounds.
G WARNING
The open bonne tmay then bloc kyour vie wwhen th evehicl eisin
motion.
There is ariskofana ccident.
X Pull ove rand stop th evehicl esafely as soo naspossible, paying
attention to roa dand traffic conditions.
X Safeguar dthe vehicl eagainst rollin gaway (Y page 172).
X Clos ethe bonnet. Active bonnet mal‐ Active bonnet mal‐
function See Own‐ function See Own‐
er'
sM anual
er' sM anual The active bonne
t(pedestrian protection )isnotactive due to amal-
function or because it has already been triggered.
X Consult aqualified specialist workshop. C At least on
edoor is open .Awarning tone also sounds.
X Clos eall doors. _
Front lef
tseat
Front lef tseat
backrest backrest not
notlocked
locked
or Front right seat
Front right seat
backrest not locked
backrest not locked The driver's or front-passenger seat backrest is no
tengaged. Awarn-
ing tone also sounds.
X Push th ebackrest bac kuntil it engages. Display
messages
281On-boardcomputer an ddisplays Z
Fron
tstowage compartments Glov
ecompartment X
To open: pull handle :and open glov ecom-
partmen tflap ;.
X To close: foldg lovec om partmen tflap ;
upward suntil it engages.
Object sinA4format or an iPad ®
,f or example,
can be store dintheglov ecom partment. For
vehicles wit haperfum eatomiser (Y page 136)
th es torag espac eoft heglov ecom partmen tis
restricted. The glov
ecom partmen tcan only be locke dand
unlocked usin gthe emergenc ykey element
(Y page 82).
X To lock: insert theemergenc ykey element
int ot he locka nd tur nit90°clockwise to
position 2.
X To unlock: insert theemergenc ykey element
int othe lockand tur nit90°anti-clockwise to
position 1. Spectacles compartment
X
To open: press marking :.
The spectacles compartmen topen sdown-
wards.
Mak esure that th espectacles compartmen tis
always closed while th evehicl eisinm otion.
Stowage compartment in th efront centre
console Illustration
:vehicles wit hDIRECT SELECT lever
X Briefly press trim ;in th edirection of the
arrow.
Cover :swings upwards.
Stowage compartment in th edoors Stowage areas
309Stowing and featu res Z
Washing the vehiclea
nd cleaning the
paintwork
Automatic car wash G
WARNING
Braking efficiency is reduced after the vehicle has been washed .There is arisk of an acci-
dent.
After washing the vehicle, brake carefully
while paying attention to the traffic conditions in order to restore full braking efficiency.
! When DISTRONIC PLUS or the HOLD func-
tion is activated, the vehicl ebrakes automat-
ically in certain situations.
To avoi ddamage to the vehicle, deactivate
DISTRONIC PLUS and the HOLD function in
the following or similar situations:
R when towing away
R in ac ar wash
! Make sure:
R the side windows and sliding sunroo fare
close dcompletely.
R the blower for the ventilation/heating is
switched off (OFF button is depressed).
R the windscreen wiper switch is at position
0
R the 360° camera or reversing camera is
switched off.
The vehicl ecouldo therwise be damaged.
! If the key is withi
nthe rear detection range
of KEYLESS-GO, the following situations, for
example, coul dleadtot he boot lid opening
unintentionally:
R using acar wash
R using ahigh-pressure cleaner
Make sure that the key is at least 3maway
from the vehicle.
! Make sure that the automatic transmission
is in neutral position Nwhen washing your
vehicl einat ow-through car wash. The vehicle
may otherwise be damaged.
R Operating with the key:
Do not remove the key from the ignition
lock. Do not open the driver's door when
the engine is switched off or at very low
speeds. Otherwise, whe nintransmission position
Dor Rthe automatic transmission
wil lautomatically switch to park position P
and block the wheels.
R Operating with the Start/Stop button:
Do not open the driver's door whe nthe
engine is switched off or at very low
speeds. Otherwise, whe nintransmission
position Dor Rthe automatic transmission
wil lautomatically switch to park position P
and block the wheels.
Observe the following to make sure that the
automatic transmission stay sinneutral position
N:
Operating with the key and Start/Stop button:
X Make sure the ignition is switched on.
X Make sure that the vehicl eisstationary.
X Depress the brake peda land keep it
depressed.
Operating with the Start/Stop button only: X Engage park position P.
X Releas ethe brake pedal.
X Remove the Start/Stop button from the igni-
tion lock (Y page145).
X Insert the key into the ignition lock.
X Switch on the ignition.
X Depress the brake peda land keep it
depressed.
Operating with the key and Start/Stop button:
X Select neutral N.
X Releas ethe brake pedal.
X Releas ethe electric parking brake, if neces-
sary.
X Switch off the ignition and leave the key in the
ignition lock.
You can wash the vehicl einanautomatic car
wash from the very start.
Was hoff excess dirt before cleaning the vehicle
in an automatic car wash.
After using an automatic car wash, wip eoff wax
from the windscreen and the wiper blades. This
wil lprevent smears and reduce wiping noises
caused by residue on the windscreen.
Washing by hand In some countries
,washing by hand is only
allowe datspeciall yequipped washing bays. Care
327Maintenance and care Z
Vehicles with MOExtende
dtyres (tyres
with run-flat characteristics) X
To remove the towin geye: open the boot
lid.
X Pull towing eye :to the left and remove it.
X To replace the towin geye: slidetowing
eye :with the thread into the rea rend of the
bracket.
X Push towing eye :on the eyelet toward sthe
right unti litengages in the bracket. Flat tyre
Preparin
gthe vehicle
Your vehicl emay be equipped with:
R MOExtende dtyres (tyres with run-fla tchar-
acteristics )(Ypage 337)
Vehicl epreparation is not necessary on vehi-
cle sw ithM OExtende dtyres.
R aT IREFIT kit (Y page 336)
R an emergency spare whee l(certai ncountries
only) (Y page 367)
Vehicles with MOExtende dtyres are not equip-
pe dw ithaT IREFIT kit at the factory .Itisthere-
fore recommende dthaty ou additionally equip
your vehicl ewithaT IREFIT kit if yo ufit tyres that
do not feature run-fla tcharacteristics, e.g .win-
ter tyres. ATIREFIT kit can be obtained from a
qualified specialist workshop.
Vehicles with an Mercedes-Benz emergency call
system which are not equipped with aTIREFIT
kit: in the event of aflatt yre, contact the Cus-
tome rAssistance Centre for the Mercedes-Benz
emergency cal lsystem (Y page 318).
Informatio nonchanging and fitting awheel
( Y page 361). X
Stop the vehicl easfar away as possibl efrom
traffic on solid ,non-slippery and level ground.
X Switch on the hazard warning lamps.
X Safeguard the vehicl eagain st rolling away
(Y page 172).
X If possible, bring the front wheels into the
straight-ahea dposition.
X Switch off the engine.
X Remove the key from the ignition lock.
or, on vehicles with KEYLESS-GO start function
or KEYLESS ‑GO:
X Ope nthe driver' sdoor.
The on-board electronics now have status 0.
Thi sist he same as the key having been
removed.
X Remove the Start/Stop button from the igni-
tio nlock( Ypage 145).
X Make sure tha tthe passenger sare not endan-
gered as they do so. Make sure tha tnoone is
nea rthe danger are awhile awheel is being
changed .Anyone wh oisnot directl yassis ting
in the whee lchange should, for example,
stand behind the barrier.
X Ge toutof the vehicle. Pa yattentio ntotraffic
conditions when doing so.
X Close the driver' sdoor.
X Place the warning triangl eatasuitabl edis-
tance (Y page 335). Observe lega lrequire-
ments. MOExtende
dtyres (tyres with run-flat
characteristics)
General notes With MOExtende
dtyres (tyres with run-fla tchar-
acteristics), yo ucan continue to drive your vehi-
cle eve nifthereisat otallos sofp ressure in one
or more tyres. The affecte dtyrem ustn ot show
any clearl yvisible damage.
Yo uc an recognise MOExtende dtyres by the
MOExtende dmarking which appears on the tyre
wall .You will find thi smarking next to the tyre
size designation, the load-bearing capacity and
the speed index.
MOExtende dtyres ma yonlybeu sedinc onjunc-
tio nw ithana ctivate dtyrep ressure loss warning
system or tyr epressure monitor. Flat tyre
337Breakdown assis tance
hitch. You could otherwise damage the vehi-
cle.
! Observe the following points when towing
with atow rope:
R Secure the tow rope on the same side on
both vehicles.
R Make sure that the tow rope is not longer
than legallyp ermitted. Mark the tow rope in
the middle, e.g. with awhite cloth
(30 x30c m).This will make other road
users aware that avehicle is being towed.
R Only secure the tow cable to the towing
eyes or, if available, to the trailer tow hitch.
R Observe the brake lamps of the towing
vehicle while driving. Always maintain adis-
tance adistance so that the tow rope does
not sag.
R Do not use steel cables or chains to tow
your vehicle. You could otherwise damage
the vehicle.
! Do not use the trailer tow hitch for recovery
or towing. Do not use the towing eye for
recovery. This could damage the vehicle. If in doubt, have the vehicle recovered using a
crane.
! Pull away smoothly when towing away or
tow-starting avehicle. If the tractive power is
too high, the vehicles could be damaged.
! Shift the automatic transmission to
Nand
do not open the driver's or front passenger's
door during towing. The automatic transmis-
sion may otherwise shift to position P,which
could damage the transmission.
! You may tow the vehicle for
amaximum of
50km.At owing speed of 50 km/h must not
be exceeded.
For towing distances over 50 km, the entire
vehicle must be lifted up and transported.
Observe the legal requirements for the relevant countries when towing.
It is better to have the vehicle transported than
to have it towed.
If the vehicle has suffered transmission damage,
have it transported on atransporter or trailer.
Vehicles with automatic transmission: when
towing avehicle, the automatic transmission
must be in position N.Ifthe automatic trans-
mission cannot be shifted to position N,have the vehicle transported on
atransporter or
trailer.
The battery must be connected and charged.
Otherwise, you:
R cannot turn the key to position 2in the igni-
tion lock
R cannot release the electric parking brake
R cannot shift the transmission to position Non
vehicles with automatic transmission
Deactivate the automatic locking feature before towing the vehicle (Y page 88). You could oth-
erwise be locked out when pushing or towing
the vehicle.
Deactivate tow-away protection before the vehi- cle is towed away (Y page 79). Fitting/removing the towing eye
Fitting the towing eye The mountings for the removable towing eyes
are located in the bumpers. They are at the rear
and at the front,u nder covers:.
X Remove the towing eye from the vehicle tool
kit (Y page 336).
X Press the mark on cover :inwards and
remove.
X Screw in the towing eye clockwise as far as it
will go and tighten it.
Vehicles with atrailer tow hitch do not have a
bracket at the back for the screw-in towing eye. Connect the towbar to the trailer tow hitch
(Y page 227). 348
Towing away and tow-startingBreakdown assistance
correct fus
erating for the system concerned.
Otherwise, components or systems could be
damaged.
! Make sure that no moistur
ecan enter the
fus eb ox whe nthe cover is open.
! Whe
nclosing the cover ,make sure that it is
lying correctly on the fus ebox. Moistur eseep-
ing in or dirt could otherwise impai rthe oper-
ation of the fuses.
The fuses in your vehicle disconnect faulty cir-
cuits. If afuseb lows ,allthe components on the
circuit and thei rfunctions will fail. Before replacing
afuse
Observe the important safety notes
(Y page 350)
X Switch off the engine.
X Switch off al lelectrical consumers.
X Safeguard the vehicle against rolling away
(Y page 172).
X Remove the key from the ignition lock.
or, on vehicle swithK EYLESS-G Ostartfunction
or KEYLESS ‑GO:
X Ope nthe driver' sdoor.
The on-board electronics now have status 0.
Thi sist he sam easthe key having been
removed.
The driver' sdoorc an be closed again.
All indicator lamps in the instrument cluster
mus tbeo ff.
The fuses are located in variou sfuseb oxes:
R fus ebox on the driver' ssideoft he dashboard
R fus eb ox in the front-passenger footwell
R fus eb ox in the engine compartment on the
driver' sside
R fus eb ox under the boo tfloor on the right-
hand sid eofthe vehicle ,whenv iewe dint he
direction of travel Dashboard fuse box
! Do not us
eapointed object such as ascrew-
driver to ope nthe cover in the dashboard. You
could damag ethe dashboard or the cover. X
Ope nthe driver' sdoor.
X To open: pull outcover :slightl yatthe bot-
tom in the direction of arrow =.
X Fold cover :outwards in the direction of
arrow ;.
X To close: foldinc over:unti lite ngages. Fus
eboxin the front-passenge rfoot-
well X
Ope nthe front-passenger door.
X To open: foldc over :outtowards the rear
and remove it.
X To close: clipinc over:at the rear.
X Fold cover :forward suntilite ngages. Fus
eboxin the engine compartment G
WARNING
Whe nthe bonne tiso pen, and the windscreen
wiper sare set in motion, yo ucan be injured by
the wiper linkage .There is ariskofi njury.
Alway sswitch off the windscreen wiper sand
the ignition before opening the bonnet. Electrical fuses
351Breakdown assistance Z
Fitting
awheel
Preparing th evehicle X
Stop th evehicl eons olid, non-slippery and
leve lground.
X Apply th eelectric parking brak emanually.
X Mov ethe fron twheels to th estraight-ahead
position.
X Vehicles with manua
ltra nsmission:
depress th eclutch pedal fully and engage first
or revers egear.
X Vehicles with automatic transmission:
shif tthe automatic transmission to position
P.
X Mak esure that th evehicl eleve liss et to "Nor-
mal" on vehicles wit hAIRMATIC (Y page 195).
X Switc hoff th eengine.
X Vehicles without KEYLESS-GO: remove the
ke yf romt heignition lock.
X Vehicles with KEYLESS-GO start-function
or KEYLESS-GO: open thedriver' sdoor.
The on-board electronics no whave status 0.
This is th esam east hekeyh aving been
removed.
X Vehicles with KEYLESS-GO start-function
or KEYLESS-GO: remove theStart/Sto pbut-
to nf romt heignition loc k(Ypage 145).
X If included in th evehicl eequipment, remove
th et yre-chang etoolkit from th evehicle.
X Safeguar dthe vehicl eagainst rollin gaway.
i Apart from som
ecountry-specific variants,
vehicles are no tequipped wit htyre-changing
tools. Some tools for changing awhee lare
specific to th evehicle. Fo rmorei nformation
on whic htools are require dtoperforma
whee lcha ng eony our vehicle, consult aquali-
fie ds pecialist workshop.
Necessary tyre-changing tools may include,
for example:
R Jack
R Whee lchock
R Whee lwrench
R Centring pin Securing th
evehicle against rolling
away If your vehicl
eisequipped wit hawheelchock ,it
can be foun dinthetyre-chang etoolkit
(Y page 336).
The foldin gwhee lchock is an additional secur-
ing measure to safeguar dthe vehicl efromr oll-
ing away, for exampl ewhen changing awheel.
X Fold bot hplates upwards :.
X Fold out lower plate ;.
X Inser tthe lugs on th elower plat efully int othe
opening sinbase plate =. X
Plac echock soro ther suitable items under
th ef ront and rear of th ewhee ltha tisd iago-
nally opposit ethe whee lyou wish to change.
Raising th evehicle G
WARNING
If you do no tposition th ejackc orre ctly at the
appropriat ejackin gpointoft hevehicle, the
jac kc ould ti poverw itht he vehicl eraised.
Ther eisar iskofi njury.
Only position th ejac katt heappropriat ejack-
ing poin tofthevehicle. The base of th ejack 362
Changing
awheelWheels and ty res