2015 MERCEDES-BENZ C-CLASS COUPE load capacity

In stowage space
:in the doors you can store
bottles with acapacity of up to 1.0 l,ar olled-up
fluorescent jacke t(driver' sdoor )and th evehicle
documen twallet (front-passenger door).
Stowage compartment/telephone com-
partmen tunder th earmre st X
To open: pressbutton :at th efront.
The stowage spac eopens.
Dependin gonthevehicle's equipment ,the fol-
lowin gmay be in th estowage space:
R am ultimedia connecto runit with 2USBports
and an SD car dslot,e.g.f or use with an
iPod ®
,i Phone ®
or MP3 player; see th esepa-
rat eo peratin ginstructions
R am obile phon ebracket
R as mall stowage spac eintheupper fron tsec-
tion Additional stowage space
Dependin gontheequipment ,the following
additional stowage areas are availabl einthe
vehicle:
R car dand coi nholde rint hedashboard above
th el ight switch (no tsuitable for holding thin
object ssuchass hoppin gtokens)
R theo pen stowage compartmen tinthecentre
console
R stowage net in th efront-pa ssenger footwell
R map pockets on th eback of th edriver' sand
front-passenger seat
R thel uggage net on th eleft-hand side in the
boot
Observ ethe loadin gguidelines (Y page 308)
and th esafety note sregardin gstowage spaces
(Y page 308). Through-loading facilit
yintherear
bench seat
Important safety notes G
WARNING
If th erear bench seat/rear seat and seat
backres tare no tengaged they coul dfold for-
wards ,e.g.w hen braking suddenly or in the
even tofana ccident.
R The vehicle occupant would thereb ybe
pushe dintot he seat belt by th erear bench
seat/rear seat or by th eseat backrest. The
seat belt canno tprotect as intended and
coul dresult in additional injury.
R Object sorloads in th eboot canno tbe
restraine dbytheseat backrest.
This pose sanincreased risk of injury.
Before ever ytrip, mak esure that th eseat
backrests and th erear bench seat/rear seat
are engaged before ever ytrip.
Observ ethe loadin gguidelines (Y page 308).
The outside and th emiddle rear seat backrests
can be folded down separately to increas ethe
boot capacity. The division ratio is 40 %to20%to
40%.
Foldin gthe rea rseat backres tforward X
Vehicle swithout memory function :ifneces-
sary, mov ethe driver' sorfront-pa ssenger
seat forwards.
X Vehicle swith memory function :when on eor
bot hpartsoft herear seat backres tare folded
forwards ,the respectiv efront seat moves
forward slightly, when necessary, in orde rto
avoid contact.
X Open th eboot.
X Fully insert th erear seat backres thead
restraints. 310
Stowage areasStowing and features

Vehicl
etoolkit
General notes The towing ey
eislocate dint he stowag ewell
under the boot floor.
On vehicles with MOExtende dtyres (tyres with
run-fla tcharacteristics) the towing ey eisina
bracket under the parcel shelf.
Apart from som ecountry-specifi cvariants, vehi-
cle sare not equipped with tyre-changing tools.
if your vehicl eisequippe dwithat yre-change
tool kit, it is locate dinthe stowag ewellu nder
the boot floor.
Some tool sfor changing awheel are specifi cto
the vehicle. For more informatio nonwhich tyre
changing tool sare required and approved to
perfor mawheelchange on your vehicle, consult
aq uali fied specialist workshop.
Necessary tyre-changing tool scan include, for
example:
R Jack
R Wheel chock
R Wheel wrench
R Ratchet ring spanner
R Centring pin
i The jack weighs approximatel
y2.1 kg.
The maximu mloadb earing capacity of the
jack can be found on the adhesive labe lonthe
jack.
The jack is maintenance-free .Ifthereisa
malfunction, please contact aquali fied spe-
cialist workshop.
Vehicles with aTIREFI Tkit :
Tyre inflation compressor
; Tyre sealant fille rbottle X
Ope nthe boot lid.
X Lif tthe boot floor upwards (Y page 313).
X Use the TIREFIT kit (Y page 338).
i Depending on the powe rclass (LK), the tyre
inflation compressor ha sthe following
weight:
R LK1 –12V /10 A, 120 W: 0.8 kg
R LK2 –12V /15A,1 80W:0.9 kg
The data regarding the power clas s(LK) and/
or electrical data can be found on the rear of
the tyre inflation compressor.
The tyre inflation compressor is maintenance-
free. If there is amalfunction, please contact
aq ualified specialist workshop.
Vehicles with atyre-change tool kit :
Tyre inflation compressor
; Tyre sealant filler bottle
= Whee lwrench
? Folding wheel chock
A Jack
B Towing eye
The tyre-change tool kit is in atray in the stow-
age wel lunde rthe boot floor.
On vehicles with aluminium hub caps, the tyre-
change tool kit also contains asocket. Depend-
ing on the vehicle equipment, this is in the left
stowage net or unde rthe boot floor.
X Open the boot lid.
X Swing the boot floo rupwards (Y page313).
X Use the TIREFIT kit (Y page338).
i Example: equipment and country-specific
variations possible. 336
Where will
Ifind...?Breakdow nassistance

Vehicles with MOExtende
dtyres (tyres
with run-flat characteristics) X
To remove the towin geye: open the boot
lid.
X Pull towing eye :to the left and remove it.
X To replace the towin geye: slidetowing
eye :with the thread into the rea rend of the
bracket.
X Push towing eye :on the eyelet toward sthe
right unti litengages in the bracket. Flat tyre
Preparin
gthe vehicle
Your vehicl emay be equipped with:
R MOExtende dtyres (tyres with run-fla tchar-
acteristics )(Ypage 337)
Vehicl epreparation is not necessary on vehi-
cle sw ithM OExtende dtyres.
R aT IREFIT kit (Y page 336)
R an emergency spare whee l(certai ncountries
only) (Y page 367)
Vehicles with MOExtende dtyres are not equip-
pe dw ithaT IREFIT kit at the factory .Itisthere-
fore recommende dthaty ou additionally equip
your vehicl ewithaT IREFIT kit if yo ufit tyres that
do not feature run-fla tcharacteristics, e.g .win-
ter tyres. ATIREFIT kit can be obtained from a
qualified specialist workshop.
Vehicles with an Mercedes-Benz emergency call
system which are not equipped with aTIREFIT
kit: in the event of aflatt yre, contact the Cus-
tome rAssistance Centre for the Mercedes-Benz
emergency cal lsystem (Y page 318).
Informatio nonchanging and fitting awheel
( Y page 361). X
Stop the vehicl easfar away as possibl efrom
traffic on solid ,non-slippery and level ground.
X Switch on the hazard warning lamps.
X Safeguard the vehicl eagain st rolling away
(Y page 172).
X If possible, bring the front wheels into the
straight-ahea dposition.
X Switch off the engine.
X Remove the key from the ignition lock.
or, on vehicles with KEYLESS-GO start function
or KEYLESS ‑GO:
X Ope nthe driver' sdoor.
The on-board electronics now have status 0.
Thi sist he same as the key having been
removed.
X Remove the Start/Stop button from the igni-
tio nlock( Ypage 145).
X Make sure tha tthe passenger sare not endan-
gered as they do so. Make sure tha tnoone is
nea rthe danger are awhile awheel is being
changed .Anyone wh oisnot directl yassis ting
in the whee lchange should, for example,
stand behind the barrier.
X Ge toutof the vehicle. Pa yattentio ntotraffic
conditions when doing so.
X Close the driver' sdoor.
X Place the warning triangl eatasuitabl edis-
tance (Y page 335). Observe lega lrequire-
ments. MOExtende
dtyres (tyres with run-flat
characteristics)
General notes With MOExtende
dtyres (tyres with run-fla tchar-
acteristics), yo ucan continue to drive your vehi-
cle eve nifthereisat otallos sofp ressure in one
or more tyres. The affecte dtyrem ustn ot show
any clearl yvisible damage.
Yo uc an recognise MOExtende dtyres by the
MOExtende dmarking which appears on the tyre
wall .You will find thi smarking next to the tyre
size designation, the load-bearing capacity and
the speed index.
MOExtende dtyres ma yonlybeu sedinc onjunc-
tio nw ithana ctivate dtyrep ressure loss warning
system or tyr epressure monitor. Flat tyre
337Breakdown assis tance

must be positioned vertically, directly under
the jacking point of the vehicle.
Observe the following when raising the vehi- cle:
R only use the vehicle-specifi cjack that has
been tested and approved by Mercedes-Benz
to rais ethe vehicle. If the jack is used incor-
rectly, it could tip over while the vehicl eis
raised.
R the jack is designed only to rais eand hold the
vehicl efor as hort time while awhee lisb eing
changed. It is not permissibl etouse it to per-
form maintenance work under the vehicle.
R avoi dchanging the whee lonuphill and down-
hill slopes.
R before raising the vehicle, safeguard it from
rolling awaybya pplying the parking brake and
positioning whee lchocks. Do not release the
parking brake while the vehicl eisraised.
R the jack must be placed on afirm, flat and
non-slip surface. On aloose surface, alarge,
flat load-bearing underlay must be used .Ona
slippery surface, anon-slip underlay must be
used ,e.g. rubber mats.
R do not use wooden blocks or similar objects
as ajack underlay.O therwise, the jack willn ot
be abletoa chieve its load-bearing capacity
due to the restricted height.
R make sure that the distance betwee nthe
underside of the tyres and the ground does
not exceed 3cm.
R never place yourh ands or feet under the
raised vehicle.
R do not lie under the vehicle.
R do not start the engine when the vehicl eis
raised.
R do not open or close adoor or the boot lid
when the vehicl eisraised.
R make sure that no persons are present in the
vehicl ewhen the vehicl eisraised.
Vehicles with light-alloy wheels and hub
caps: the whee lbolts are covered by ahub cap.
Before you can unscrew the whee lbolts, you
must remove the hub cap. Two different variants
can be fitted. Vehicles with plastic hub cap:
X To remove: turn the centre cover of hub
cap :anti-clockwis eand remove.
X To fit: before fitting, ensure that hub cap :is
in the open position. To do this, turn the
centre cover anti-clockwise.
X Position hub cap :and turn the centre cover
clockwise until hub cap :engage sphysically
and audibly.
X Make sure that hub cap :is fitted securely. Vehicles with aluminium hub cap:
X To remove: take socket;and whee lwrench
= from the vehicl etool kit (Y page 336).
X Position socket ;on hub cap :.
X Position whee lwrench =on socket ;.
X Using whee lwrench =,turn hub cap :anti-
clockwise and remove it.
X To fit: before fitting, check hub cap :and
the whee larea for dirt and clean if necessary.
X Put hub cap :in position and turn until it is in
the right position.
X Position socket ;on hub cap :.
X Attach whee lwrench =to socket ;and
tighten hub cap :.
The tightening torque must be 25 Nm. Changing
awheel
363Wheelsa nd tyres Z