2015 MAZDA MODEL CX-3 battery

6–39
Maintenance and Care
Owner Maintenance
Key Battery Replacement
If the buttons on the transmitter are
inoperable and the operation indicator
light does not fl ash, the battery may be
dead.
Replace with a new battery before the
transmitter becomes unusable.
CAUTION
  Make sure the battery is installed
correctly. Battery leakage could
occur if it is not installed correctly.
  When replacing the battery, be
careful not to touch any of the
internal circuitry and electrical
terminals, bend the electrical
terminals, or get dirt in the
transmitter as the transmitter could
be damaged.
  There is the danger of explosion if
the battery is not correctly replaced.
  Dispose of used batteries according
to the following instructions.
 


 Insulate the plus and minus
terminals of the battery using
cellophane or equivalent tape.
 


 Never disassemble.



 Never throw the battery into fi re or
water.
 


 Never deform or crush. 

 Replace only with the same type
battery (CR2025 or equivalent).
The following conditions indicate that the
battery power is low:
 


 The KEY indicator light (green) fl ashes
in the instrument cluster for about 30
seconds after the engine is turned off.
 


 The system does not operate and
the operation indicator light on the
transmitter does not fl ash when the
buttons are pressed.
 


 The system's operational range is
reduced.
Replacing the battery at an Authorised
Mazda Repairer is recommended to
prevent damage to the key. If replacing the
battery by yourself, follow the instruction
below.
Replacing the key battery
1. Press the knob and pull out the
auxiliary key.
Knob
$9@&;&&%@&EJUJPOJOEC







6–40
Maintenance and Care
Owner Maintenance
2. Twist a tape-wrapped fl athead
screwdriver in the direction of the
arrow and open the cover slightly.
Cover
3. Insert the tape-wrapped fl athead
screwdriver into the gap and slide it in
the direction of the arrow.
Cover
Gap
4. Twist the fl athead screwdriver in the
direction of the arrow and remove the
cover.
Cover
5. Remove the battery cap, then remove
the battery.
6. Insert a new battery with the positive
pole facing up, and then cover the
battery with the battery cap.
7. Close the cover.
8. Reinsert the auxiliary key.
$9@&;&&%@&EJUJPOJOEC







6–41
Maintenance and Care
Owner Maintenance
CAUTION
  Be careful not to allow the rubber
ring shown in the fi gure to be
scratched or damaged.
  If the rubber ring detaches, reattach it
before inserting a new battery.
Rubber ring
Ty r e s
For reasons of proper performance, safety,
and better fuel economy, always maintain
recommended tyre infl ation pressures and
stay within the recommended load limits
and weight distribution.
WARNING
Using Different Tyre Types:
Driving your vehicle with different
types of tyres is dangerous. It could
cause poor handling and poor braking;
leading to loss of control.
Except for the limited use of the
temporary spare tyre, use only the same
type tyres (radial, bias-belted, bias-type)
on all four wheels.
Using Wrong-Sized Tyres:
Using any other tyre size than what
is specifi ed for the vehicle (page 9-9 )
is dangerous. It could seriously affect
ride, handling, ground clearance,
tyre clearance, and speedometer
calibration. This could cause you to
have an accident. Use only tyres that
are the correct size specifi ed for the
vehicle.
$9@&;&&%@&EJUJPOJOEC







*Some models.6–65
Maintenance and Care
Appearance Care
Aluminium Wheel Maintenance *
A protective coating is provided over the
aluminium wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than mild
detergent. Before using any detergent,
verify the ingredients. Otherwise, the
product could discolour or stain the
aluminium wheels.
NOTE
  Do not use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminium
wheels. They may damage the
coating.
  Always use a sponge or soft cloth to
clean the wheels.
 Rinse the wheels thoroughly with
lukewarm or cold water. Also, be
sure to clean the wheels after driving
on dusty or salted roads to help
prevent corrosion.
  Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
 (18-inch wheel vehicle) If your aluminium wheels lose
lustre, apply wax which contains no
polishing powder.
Plastic Part Maintenance
 












 When cleaning the plastic lenses of
the lights, do not use petrol, paraffi n,
rectifi ed spirit, paint, thinner, highly
acidic detergents, or strongly alkaline
detergents. Otherwise, these chemical
agents can discolour or damage the
surfaces resulting in a signifi cant loss
in functionality. If plastic parts become
inadvertently exposed to any of these
chemical agents, fl ush with water
immediately.
 


 If plastic parts such as the bumpers
become inadvertently exposed to
chemical agents or fl uids such as petrol,
oil, engine coolant, or battery fl uid, it
could cause discolouration, staining,
or paint peeling. Wipe off any such
chemical agents or fl uids using a soft
cloth immediately.
 


 High water temperature and high water
pressure car washers are available
depending on the type of high pressure
car washer device. If the car washer
nozzle is put too close to the vehicle or
aimed at one area for an extended period
of time, it could deform plastic parts or
damage the paint.
 


 Do not use wax containing compounds
(polish). Otherwise, it could result in
paint damage.
 


 In addition, do not use an electrical or
air tool to apply wax. Otherwise, the
frictional heat generated could result
in deformation of plastic parts or paint
damage.
$9@&;&&%@&EJUJPOJOEC







*Some models.7–1
7If Trouble Arises
Helpful information on what to do if a problem arises with the vehicle.



Parking in an Emergency .................................................................. 7-2
Parking in an Emergency .............................................................. 7-2
Flat Tyre .............................................................................................. 7-3
Spare Tyre and Tool Storage ......................................................... 7-3
Emergency Flat Tyre Repair Kit
* ................................................ 7-10
Changing a Flat Tyre (With Spare Tyre) ..................................... 7-17
Battery Runs Out ............................................................................. 7-24
Jump-Starting .............................................................................. 7-24
Emergency Starting ......................................................................... 7-27
Starting a Flooded Engine (SKYACTIV-G 2.0 ) ........................ 7-27
Push-Starting ............................................................................... 7-27
Running Out of Fuel (SKYACTIV-D 1.5) .................................. 7-28
Overheating ...................................................................................... 7-29
Overheating ................................................................................. 7-29
Emergency Towing ........................................................................... 7-31
Towing Description ..................................................................... 7-31
Towing/Tiedown Hooks .............................................................. 7-32
Warning/Indicator Lights and Warning Sounds ........................... 7-35
If a Warning Light Turns On or Flashes...................................... 7-35
Message Indicated on Display
* ................................................... 7-48
Warning Sound is Activated ........................................................ 7-50
When Liftgate Cannot be Opened .................................................. 7-55
When Liftgate Cannot be Opened ............................................... 7-55
Active Driving Display Does Not Operate ..................................... 7-56
If the Active Driving Display does not operate .......................... 7-56
$9@&;&&%@&EJUJPOJOEC







7–24
If Trouble Arises
Battery Runs Out
Jump-Starting
Jump-starting is dangerous if done incorrectly. So follow the procedure carefully. If you
feel unsure about jump-starting, we strongly recommend that you have a competent service
technician do the work.
WARNING
Follow These Precautions Carefully:
To ensure safe and correct handling of the battery, read the following precautions
carefully before using the battery or inspecting it.
Do not allow the positive ( ) terminal to contact any other metal object that
could cause sparks:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries. When working near a battery,
do not allow metal tools to contact the positive (
) or negative () terminal of the
battery.
Keep all fl ames, including cigarettes, and sparks away from open battery cells:
Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced
during normal battery operation, could ignite and cause the battery to explode. An
exploding battery can cause serious burns and injuries.
Do not jump-start a frozen battery or one with a low fl uid level:
Jump-starting a frozen battery or one with a low fl uid level is dangerous. It may rupture
or explode, causing serious injury.
Connect the negative lead to a good ground point away from the battery:
Connecting the end of the second jumper lead to the negative (
) terminal of the
discharged battery is dangerous.
A spark could cause the gas around the battery to explode and injure someone.
Route the jumper leads away from parts that will be moving:
Connecting a jumper lead near or to moving parts (cooling fans, belts) is dangerous.
The lead could get caught when the engine starts and cause serious injury.
$9@&;&&%@&EJUJPOJOEC







7–25
If Trouble Arises
Battery Runs Out
CAUTION
Use only a 12 V booster system. You can damage a 12 V starter, ignition system, and other
electrical parts beyond repair with a 24 V power supply (two 12 V batteries in series or a
24 V motor generator set).
Jumper leads
Discharged battery
Booster battery
$9@&;&&%@&EJUJPOJOEC







7–26
If Trouble Arises
Battery Runs Out
1. Remove the battery cover.
2. Make sure the booster battery is 12
V and that its negative terminal is
grounded.
3. If the booster battery is in another
vehicle, do not allow both vehicles
to touch. Turn off the engine of the
vehicle with the booster battery and
all unnecessary electrical loads in both
vehicles.
4. Connect the jumper leads in the exact
sequence as in the illustration.
 

 
 Connect one end of a lead to the
positive terminal on the discharged
battery (1).
 

 
 Attach the other end to the positive
terminal on the booster battery (2).
 

 
 Connect one end of the other lead to
the negative terminal of the booster
battery (3).
 

 
 Connect the other end to the ground
point indicated in the illustration away
from the discharged battery (4).
5. Start the engine of the booster vehicle
and run it a few minutes. Then start the
engine of the other vehicle.
6. When fi nished, carefully disconnect the
leads in the reverse order described in
the illustration. 7. If the battery cover has been removed,
install it in the reverse order of
removal.
NOTE
Verify that the covers are securely
installed.
$9@&;&&%@&EJUJPOJOEC