2015 MAZDA MODEL CX-3 clock reset

*Some models.5–29
Interior Features
Audio System
Indication Setting value Turn
Anticlockwise Turn
Clockwise
BT SETUP
*2 Select mode
12Hr
24Hr
(12 Hr/24 Hr time
adjustment) 12Hr
(Flashing) 24Hr
(Flashing)
*1 Type B
*2 Depending on the model, this function
may not be available.
NOTE
If not operated for several seconds, the
display returns to the previous display.
To reset bass, treble, fade, and balance,
press the menu button (
) for 2
seconds. The unit will beep and
“ CLEAR ” will be displayed.
AF (Setting Alternative Frequency
(AF)) (Type B)
The AF function of the Radio Data System
(RDS) can be set on or off.
Refer to Operating the Radio (Type B) on
page 5-34 .
REG (Setting Regional Programme
(REG)) (Type B)
The REG function of the Radio Data
System (RDS) can be set on or off.
Refer to Operating the Radio (Type B) on
page 5-34 . ALC (Automatic volume adjustment)
The automatic level control (ALC)
changes the audio volume automatically
according to the vehicle speed. The faster
the vehicle speed, the higher the volume
increases. ALC has ALC OFF and ALC
LEVEL 1 to 7 modes. At ALC LEVEL 7,
the amount that the volume can increase
is at the maximum. Select the mode
according to the driving conditions.
BEEP (Audio operation sound)
The setting for the operation sound when
pressing and holding a button can be
changed. The initial setting is ON. Set to
OFF to mute the operation sound.
BT SETUP mode *
Music and other audio such as voice data
recorded on portable audio devices and
mobile phones available on the market
which are equipped with the Bluetooth
®
transmission function can be listened to
via wireless transmission over the vehicle's
speakers. Using the BT SETUP mode,
these devices can be programmed to the
Bluetooth
® unit or changed (page 5-92 ).
12Hr
24Hr (12 Hr/24 Hr time
adjustment)
Rotating the audio control dial switches
the display between 12 and 24-hour clock
time (page 5-30 ).
$9@&;&&%@&EJUJPOJOEC







5–30
Interior Features
Audio System
Clock
Audio display Audio control dial
Hour/Minute set switch:00 button
Menu button Clock button
The figure is an example showing the type A unit.
Setting the time
The clock can be set at any time when the
ignition is switched to ACC or ON.
1. To adjust the time, press the clock
button (
) for about 2 seconds until
a beep is heard.
2. The clock's current time will fl ash.
Time adjustment



 
 To adjust the time, press the hour/
minute set button (
,) while the
clock's current time is fl ashing.



 
 The hours advance while the hour set
button (
) is pressed. The minutes
advance while the minute set button
(
) is pressed.
3. Press the clock button (
) again to
start the clock.
Time resetting
1. Press the clock button (
) for about
2 seconds until a beep is heard.
2. Press the :00 button ( 1 ).
3. When the button is pressed, the time
will be reset as follows:
(Example)
12:01—12:29
:12:00
12:30—12:59
:1:00
NOTE

 When the :00 button ( 1 ) is pressed,
the seconds will start at “ 00 ”.

 Switching between 12 and 24-hour
clock time:
 Press the menu button ()
several times until 12 and 24-hour
clock time are displayed. Turn the
audio control dial in either direction,
select the desired clock setting while
the preferred clock time is fl ashing.
$9@&;&&%@&EJUJPOJOEC







5–48
Interior Features
Audio System
Volume/Display/Sound Controls
Volume dialVolume switch Commander switchAudio control switch
Volume adjustment
Turn the commander switch volume dial.
The volume switch on the steering switch
can also be pressed.
Display setting
Select the
icon on the home screen and
display the Settings screen.
Select the
tab to select the item you
would like to change.
Display OFF/Clock
The centre display can be turned off.
Select
to turn the display off.
When
is
selected the centre display turns off and
the clock is displayed.
The centre display can be turned back on
as follows:
 


 Touch the centre display.



 Operate the commander switch. Daytime/nighttime (Mode) screen
setting
The daytime or nighttime screen can be
selected.
: Switches screen automatically
according to headlight illumination
condition
*1
: Daytime screen setting
: Nighttime screen setting
*1 The display is constantly on daytime
screen when the illumination dimmer is
cancelled.
Brightness adjustment
Adjust the centre display brightness using
the slider.
Contrast adjustment
Adjust the centre display contrast using
the slider.
Display setting reset
All of the screen setting values can be
reset to their initial settings.
1. Select
.
2. Select
.
$9@&;&&%@&EJUJPOJOEC