2015 MAZDA MODEL 6 warning light

Black plate (257,1)
qWhen The System Operates
1. Press the LDWS switch. The LDWS
goes on stand-by and the LDWS
warning light (amber) illuminates.
On the type A instrument cluster, the
lane indication (bordered line) is
indicated in the display.
Indication on display
2. Drive the vehicle near the center of the
lane and the LDWS indicator light
(green) illuminates in the instrument
cluster when all of the following
conditions are met.
On the type A instrument cluster, the
lane indication is indicated in the
display.
lThe vehicle is driven near the center
of the lane with the white (yellow)
line on the left and right sides, or on
either side.
lThe vehicle speed is about 65 km/h
(41 mph) or more
lThe vehicle is driven on a straight
road or road with gentle curves
Indication on display
NOTElThe LDWS remains on stand-by until it
detects white (yellow) lines on both the left
and right sides, or on either side.
lWhen the system detects a white (yellow)
line on one side only, the system will
operate the warning only when the vehicle
deviates to the side the white (yellow) line
detected.
When Driving
Lane Departure Warning System (LDWS)
4-133
Mazda6_8DQ8-EA-13L_Edition3 Page257
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (258,1)
Auto cancel
Under the following conditions, the
LDWS is automatically canceled and kept
on stand-by, and the LDWS warning light
(amber) in the instrument cluster
illuminates.
On the type A instrument cluster, the lane
indication (bordered line) is indicated in
the display.
The LDWS is automatically enabled when
the condition changes and the system is
operable.
lThe system cannot detect white
(yellow) lines.
lThe vehicle speed is less than about 60
km/h (37 mph).
lThe vehicle is making a sharp curve.lThe vehicle is making a curve at an
inadequate speed.
lThe temperature inside the camera is
high or low.
lThe windshield around the camera is
foggy.
lThe windshield around the camera is
blocked by an obstruction, causing
poor forward visibility.
Auto cancel of warning
Under the following conditions, the
LDWS determines that the driver is
making lane changes and the warning is
automatically canceled.
The LDWS is automatically enabled after
the operation.
lThe steering wheel is operated
abruptly.
lThe brake pedal is depressed abruptly.lThe accelerator pedal is depressed
abruptly.
lA turn signal lever is operated (after
the turn signal lever is returned, the
LDWS warning may not operate for
about 3 seconds which is the period of
time required to make a lane
correction).
NOTE
lAfter about 5 seconds have elapsed with the
turn signal lever left operating, the LDWS
warning may operate if the vehicle is close
to a white (yellow) line.
lThe sensitivity of the warning (sensitivity
with which the system determines the
driver’s intentional lane change) can be
changed.
Refer to Personalization Features on page 9-9.
qCanceling The System
To cancel the LDWS, press the LDWS
switch. The LDWS indicator light (Green/
Amber) in the instrument cluster turns off.
The lane indication displayed in the type
A instrument cluster turns off.
qLDWS Warning
If the system determines that the vehicle
may be deviating from its lane while the
system is operating, the LDWS warning
sounds and the LDWS indicator light
(green) flashes.
Refer to Warning/Indicator Lights on page
4-23.
Refer to Lane Departure Warning System
(LDWS) Warning Sound on page 7-41.
In the display of the type A instrument
cluster, the direction in which the system
determined that the vehicle may be
deviating from its lane is indicated.
Operate the steering wheel adequately and
drive in the center of the lane.
4-134
When Driving
Lane Departure Warning System (LDWS)
Mazda6_8DQ8-EA-13L_Edition3 Page258
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (259,1)
Indication on display
NOTElIf the LDWS warning sound is set to
rumble, the sound will be heard from the
vehicle speaker on the side which the
system determined the vehicle may be
deviating from its lane.
lThe LDWS warning sound may not be
heard depending on the surrounding
conditions such as outside noise.
lThe warning timing with which the system
determines the vehicle may be deviating
from its lane can be changed.
Refer to Personalization Features on page
9-9.
qForward Sensing Camera (FSC)
lThe LDWS camera, located near the
rearview mirror, also functions as the
Forward Sensing Camera (FSC) for the
High Beam Control System (HBC).
lIf the temperature inside the Forward
Sensing Camera (FSC) is extremely
high or low, the LDWS is
automatically canceled and kept on
stand-by, and the LDWS warning light
(amber) in the instrument cluster
flashes. Message information is
indicated in the display in the type A
instrument cluster.
The LDWS is automatically enabled
when the conditions change and the
system is operable.
Forward Sensing Camera (FSC)
When Driving
Lane Departure Warning System (LDWS)
4-135
Mazda6_8DQ8-EA-13L_Edition3 Page259
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (279,1)
CAUTION
If the air conditioner is used while
driving up long hills or in heavy
traffic, monitor the engine coolant
temperature warning light to see if it
is illuminated or flashing (page 4-23).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or flashing, turn the air
conditioning off (page 7-24).
NOTE
lWhen maximum cooling is desired, set the
temperature control dial to the extreme cold
position and set the air intake selector to
the recirculated air mode, then turn the fan
control dial fully clockwise.
lIf warmer air is desired at floor level, set
the mode selector dial at the
position
and adjust the temperature control dial to
maintain maximum comfort.
lThe air to the floor is warmer than air to
the face (except when the temperature
control dial is set at the extreme hot or cold
position).
qVentilation
1. Set the mode selector dial to the
position.
2. Set the air intake selector to the outside
air mode.
3. Set the temperature control dial to the
desired position.
4. Set the fan control dial to the desired
speed.
qWindshield Defrosting and Defogging
1. Set the mode selector dial to the
position.
2. Set the temperature control dial to the
desired position.
3. Set the fan control dial to the desired
speed.
4. If dehumidified heating is desired, turn
on the air conditioner.
WARNING
Do not defog the windshield using the
position with the temperature
control set to the cold position:
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windshield to fog
up. Your vision will be hampered,
which could lead to a serious
accident. Set the temperature control
to the hot or warm position when
using the
position.
NOTE
lFor maximum defrosting, turn on the air
conditioner, set the temperature control dial
to the extreme hot position, and turn the fan
control dial fully clockwise.
lIf warm air is desired at the floor, set the
mode selector dial to the
position.lIn theorposition, the air
conditioner is automatically turned on and
the outside air mode is automatically
selected to defrost the windshield. In the
orposition, the outside air mode
cannot be changed to the recirculated air
mode.
Interior Features
Climate Control System
5-7
Mazda6_8DQ8-EA-13L_Edition3 Page279
Friday, June 13 2014 6:22 PM
Form No.8DQ8-EA-13L

Black plate (283,1)
Outside air position ()
Use this mode for ventilation or
windshield defrosting.
WARNING
Do not use theposition in cold or
rainy weather:
Using the
position in cold or
rainy weather is dangerous as it will
cause the windows to fog up. Your
vision will be hampered, which could
lead to a serious accident.
DUAL switch
Use the DUAL switch to change the mode
between the individual operation (driver
and passenger) and interconnection
(simultaneous) modes.
Individual operation mode (indicator
light illuminated)
The set temperature can be controlled
individually for the driver and front
passenger.
Interconnection mode (indicator light
turned off)
The set temperature for the driver and
front passenger is controlled
simultaneously.
Windshield defroster switch
Press the switch to defrost the windshield
and front door windows.
qOperation of Automatic Air
Conditioning
1. Press the AUTO switch. Selection of
the airflow mode, air intake selector
and amount of airflow will be
automatically controlled.
2. Use the temperature control dial to
select a desired temperature.
Press the DUAL switch or turn the
front passenger temperature control
dial to control the set temperature
individually for the driver and front
passenger.
To turn off the system, press the OFF
switch.
NOTE
lSetting the temperature to maximum high
or low will not provide the desired
temperature at a faster rate.
lWhen selecting heat, the system will restrict
airflow until it has warmed to prevent cold
air from blowing out of the vents.
qWindshield Defrosting and Defogging
Press the windshield defroster switch.
In this position, the outside air position is
automatically selected, and the air
conditioner automatically turns on. The
air conditioner will directly dehumidify
the air to the front windshield and side
windows (page 5-4). Airflow amount will
be increased.
Interior Features
Climate Control System
5-11
Mazda6_8DQ8-EA-13L_Edition3 Page283
Friday, June 13 2014 6:22 PM
Form No.8DQ8-EA-13L

Black plate (284,1)
WARNING
Set the temperature control to the hot
or warm position when defogging (
position):
Using the
position with the
temperature control set to the cold
position is dangerous as it will cause
the outside of the windshield to fog
up. Your vision will be hampered,
which could lead to a serious
accident.
NOTE
Use the temperature control dial to increase
the air flow temperature and defog the
windshield more quickly.
qSunlight/Temperature Sensor
The fully automatic air conditioner
function measures inside and outside
temperatures, and sunlight. It then sets
temperatures inside the passenger
compartment accordingly.
CAUTION
Do not obstruct either sensor,
otherwise the automatic air
conditioner will not operate properly.
Sunlight sensor
Interior temperature sensor
5-12
Interior Features
Climate Control System
Mazda6_8DQ8-EA-13L_Edition3 Page284
Friday, June 13 2014 6:22 PM
Form No.8DQ8-EA-13L

Black plate (388,1)
Accessory Sockets
Only use genuine Mazda accessories or
the equivalent requiring no greater than
120 W (DC 12 V, 10 A).
Front
The ignition must be switched to ACC or
ON.
Center
The accessory socket can be used
regardless of whether the ignition is on or
off.
CAUTION
ØTo prevent accessory socket
damage or electrical failure, pay
attention to the following:
ØDo not use accessories that
require more than 120 W (DC 12
V, 10 A).
ØDo not use accessories that are
not genuine Mazda accessories
or the equivalent.
ØClose the cover when the
accessory socket is not in use to
prevent foreign objects and
liquids from getting into the
accessory socket.
ØCorrectly insert the plug into
the accessory socket.
ØDo not insert the cigarette
lighter into the accessory
socket.
ØNoise may occur on the audio
playback depending on the device
connected to the accessory socket.
ØDepending on the device
connected to the accessory socket,
the vehicle's electrical system may
be affected, which could cause the
warning light to illuminate.
Disconnect the connected device
and make sure that the problem is
resolved. If the problem is
resolved, disconnect the device
from the socket and switch the
ignition off. If the problem is not
resolved, consult an Authorized
Mazda Dealer.
NOTE
To prevent discharging of the battery, do not
use the socket for long periods with the engine
off or idling.
5-116
Interior Features
Interior Equipment
Mazda6_8DQ8-EA-13L_Edition3 Page388
Friday, June 13 2014 6:22 PM
Form No.8DQ8-EA-13L

Black plate (391,1)
Storage Compartments
WARNING
Keep storage boxes closed when
driving:
Driving with the storage boxes open
is dangerous. To reduce the
possibility of injury in an accident or
a sudden stop, keep the storage
boxes closed when driving.
Do not put articles in storage spaces
with no lid:
Putting articles in storage spaces
with no lid is dangerous as they
could be thrown around the cabin if
the vehicle is suddenly accelerated
and cause injury depending on how
the article is stored.
CAUTION
Do not leave lighters or eyeglasses in
the storage boxes while parked under
the sun. A lighter could explode or
the plastic material in eyeglasses
could deform and crack from high
temperature.
qOverhead Console
This console box is designed to store
eyeglasses or other accessories.
Push and release to open.
qStorage Pocketí
To use, open the lid.
Interior Features
Interior Equipment
5-119íSome models. Mazda6_8DQ8-EA-13L_Edition3 Page391
Friday, June 13 2014 6:22 PM
Form No.8DQ8-EA-13L