2015 MAZDA MODEL 3 HATCHBACK display

4–14 6
When Driving
i-ACTIVSENSE
NOTE
  The Smart Brake Support (SBS) system operates when all of the following conditions
are met:
 


 The ignition is switched ON.



 The Smart Brake Support (SBS) system is on.



 The DSC OFF indicator light is not illuminated.



 The vehicle speed is about 15 km/h or faster (10 mph or faster).



 The relative speed between your vehicle and the vehicle ahead is about 15 km/h or
faster (10 mph or faster).
 


 The Dynamic Stability Control (DSC) is not operating. 

 The Smart Brake Support (SBS) system may not operate under the following
conditions:
 


 If there is the possibility of hitting only a part of a vehicle ahead.



 If the vehicle is accelerated rapidly and it comes close to a vehicle ahead.



 The vehicle is driven at the same speed as the vehicle ahead.



 The accelerator pedal is depressed.



 The brake pedal is depressed.



 The steering wheel is being operated.



 The selector lever is being operated.



 The direction indicator is being used. 

 Although the objects which activate the system are 4-wheeled vehicles, the radar
sensor could detect the following objects, determine them to be an obstruction, and
operate the Smart Brake Support (SBS) system.
 


 Objects on the road at the entrance to a curve (including guardrails and snow banks).



 A vehicle appears in the opposite lane while cornering or rounding a curve.



 When crossing a narrow bridge.



 When passing under a low gate or through a tunnel or narrow gate.



 When entering an underground parking area.



 Metal objects, bumps, or protruding objects on the road.



 If you suddenly come close to a vehicle ahead.



 When driving in areas where there is high grass or forage.



 Two-wheeled vehicles such as motorbikes or bicycles.



 Pedestrians or non-metallic objects such as standing trees. 

 When the system operates, the user is notifi ed by the fl ashing Smart Brake Support
(SBS) indicator light (red) and the active driving display.
  The Smart Brake Support (SBS) warning light (amber) turns on when the system has a
malfunction.
 Refer to Warning Lights on page 4-41 .
.B[EB@&'&&"@&EJUJPOJOEC







4–147
When Driving
i-ACTIVSENSE
Smart Brake Support (SBS)
Indicator Light (Red)
If the Smart Brake Support (SBS) is
operating, the indicator light (red) fl ashes.
Collision Warning
If there is the possibility of a collision
with a vehicle ahead, the beep sounds
continuously and a warning is indicated in
the display.
Stopping The Smart Brake
Support (SBS) System Operation
The Smart Brake Support (SBS) system
can be temporarily deactivated.
Refer to Personalisation Features on page
9-16 .
When the Smart Brake Support (SBS)
system is turned off, the Smart Brake
Support (SBS) OFF indicator light turns
on.
When the engine is restarted, the system
becomes operational.
NOTE
If the Smart Brake Support (SBS)
system operation is turned off, the Smart
City Brake Support (SCBS) system
operation is turned off simultaneously.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–150
When Driving
i-ACTIVSENSE
Radar Sensor (Front) *
Your vehicle is equipped with a radar sensor (front).
The following systems also use the radar sensor (front).
 


 Smart Brake Support (SBS)



 Mazda Radar Cruise Control (MRCC)



 Distance Recognition Support System (DRSS)
The radar sensor (front) functions by detecting the radio waves refl ected off a vehicle ahead
or an obstruction sent from the radar sensor (front).
The radar sensor (front) is mounted behind the front emblem.
Radar sensor (front)
If the Smart Brake Support (SBS) warning light (amber) is illuminated, the area around the
radar sensor (front) may be dirty. Refer to “Warning Guidance” in the centre display (Type
B audio).
Refer to If a Warning Light Turns On or Flashes on page 7-32 .
.B[EB@&'&&"@&EJUJPOJOEC







4–158
When Driving
Cruise Control
3. Set the cruise control by pressing the
SET
or SET switch at the desired
speed. The cruise control is set at the
moment the SET
or SET switch is
pressed. Release the accelerator pedal
simultaneously. The cruise set indicator
light (Green) illuminates.
NOTE
  The cruise control speed setting
cannot be performed under the
following conditions:
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.


 Release the SET or SET switch
at the desired speed, otherwise the
speed will continue increasing while
the SET
switch is pressed and
held, and continue decreasing while
the SET
switch is pressed and held
(except when the accelerator pedal is
depressed).
  On a steep grade, the vehicle may
momentarily slow down while
ascending, or speed up while
descending.
NOTE
  Cruise control will cancel if the
vehicle speed decreases below
21 km/h (13 mph) when cruise is
activated, such as when climbing a
steep grade.
  Cruise control may cancel at about
15 km/h (9 mph) below the preset
speed (such as may happen when
climbing a long, steep grade).
To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the SET
switch and hold it. Your
vehicle will accelerate. Release the switch
at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET
or
SET
switch and release it immediately.
.B[EB@&'&&"@&EJUJPOJOEC







4–159
When Driving
Cruise Control
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is
on. Greater speed will not interfere with
or change the set speed. Take your foot
off the accelerator to return to the set
speed.
To Decrease Cruising Speed
Press the SET switch and hold it. The
vehicle will gradually slow.
Release the switch at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will decrease the
preset speed according to the number of
times it is operated.
Decreasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To Resume Cruising Speed at
More Than 25 km/h (16 mph)
If some other method besides the OFF
switch was used to cancel cruising speed
(such as applying the brake pedal) and the
system is still activated, the most recent
set speed will automatically resume when
the RESUME switch is pressed.
If vehicle speed is below 25 km/h (16
mph), increase the vehicle speed up to
25 km/h (16 mph) or more and press the
RESUME switch.
To Temporarily Cancel
To temporarily cancel the system, use one
of these methods:
 


 Slightly depress the brake pedal.



(Manual transaxle)
 Depress the clutch pedal.



 Press the CANCEL switch.
If the RESUME switch is pressed when
the vehicle speed is 25 km/h (16 mph) or
higher, the system reverts to the previously
set speed.
NOTE
  If any of the following conditions
occur, the cruise control system is
temporarily cancelled.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 
 When the cruise control system is
temporarily cancelled by even one of
the applicable cancel conditions, the
speed cannot be re-set.
 (Automatic transaxle) The cruise control cannot be
cancelled while driving in manual
mode (selector lever shifted from
D to M position). Therefore, engine
braking will not be applied even
if the transaxle is shifted down
to a lower gear. If deceleration is
required, lower the set speed or
depress the brake pedal.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.4–16 6
When Driving
Rear View Monitor
Rear View Monitor *
The rear view monitor provides visual images of the rear of the vehicle when reversing.
WARNING
Always drive carefully confi rming the safety of the rear and the surrounding conditions
by looking directly with your eyes:
Reversing the vehicle by only looking at the screen is dangerous as it may cause an
accident or a collision with an object. The rear view monitor is only a visual assist
device when reversing the vehicle. The images on the screen may be different from the
actual conditions.
CAUTION
  Do not use the rear view monitor under the following conditions: Using the rear view
monitor under the following conditions is dangerous and could result in injury or
vehicle damage or both.
 


 Icy or snow-covered roads.



 Tyre chains or a temporary spare tyre is installed.



 The boot lid/liftgate is not fully closed.



 The vehicle is on a road incline. 

 When the display is cold, images may course across the monitor or the screen and
may be dimmer than usual, which could cause diffi culty in confi rming the surrounding
conditions of the vehicle. Always drive carefully confi rming the safety of the rear and
the surrounding conditions by looking directly with your eyes.
  Do not apply excessive force to the camera. The camera position and angle may
deviate.
  Do not disassemble, modify, or remove it as it may no longer be waterproof. 
 The camera cover is made of plastic. Do not apply degreasing agents, organic solvents,
wax, or glass coating agents to the camera cover. If any are spilled on the cover, wipe
off with a soft cloth immediately.
  Do not rub the cover excessively, or polish it using an abrasive compound or a hard
brush. The cover may be damaged affecting the image.
.B[EB@&'&&"@&EJUJPOJOEC







4–167
When Driving
Rear View Monitor
NOTE
  If water, snow, or mud is stuck on the camera lens, wipe it off using a soft cloth. If it
cannot be wiped off, use a mild detergent.
  If the camera temperature changes rapidly (Hot to cold, cold to hot), the rear view
monitor may not operate correctly.
  When replacing the tyres, consult an expert repairer, we recommend an Authorised
Mazda Repairer. Replacing the tyres could result in deviation of the guide lines which
appear on the display.
  If the vehicle's front, side, or rear has been involved in a collision, the alignment of
the rear view parking camera (location, installation angle) may have deviated. Always
consult an expert repairer, we recommend an Authorised Mazda Repairer to have the
vehicle inspected.
  If “No Video Signal Available” is indicated in the display, there could be a problem
with the camera. Have your vehicle inspected at an expert repairer, we recommend an
Authorised Mazda Repairer.
Rear View Parking Camera Location
Rear View Parking Camera Saloon Hatchback
Switching to the Rear View Monitor Display
Shift the shift lever to R with the ignition switched ON to switch the display to the rear view
monitor display.
NOTE
When the shift lever is shifted from R to another shift lever position, the screen returns to
the previous display.
.B[EB@&'&&"@&EJUJPOJOEC







4–16 8
When Driving
Rear View Monitor
Displayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
Boot lid (saloon)/
garnish (hatchback) Obstruction detection
indication in parking
sensor system.
Bumper
Object
Some models (Actual view)
NOTE
  The displayable range varies depending on the vehicle and road conditions. 
 The displayable range is limited. Objects under the bumper or around the bumper ends
cannot be displayed.
  The distance appearing in the displayed image is different from the actual distance
because the rear view parking camera is equipped with a specifi c lens.

 Some optionally installed vehicle accessories may be picked up by the camera. Do not
install any optional parts that can interfere with the camera view, such as illuminating
parts or parts made of refl ective material.

 It may be diffi cult to see the display under the following conditions, however, it does
not indicate a malfunction.
 


 In darkened areas.



 When the temperature around the lens is high/low.



 When the camera is wet such as on a rainy day or during periods of high humidity.



 When foreign material such as mud is stuck around the camera.



 When the camera lens refl ects sunlight or headlight beams. 

 Image display may be delayed if the temperature around the camera is low.
.B[EB@&'&&"@&EJUJPOJOEC