2015 AUDI S7 sensor

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
caused by airbags when they inflate, particu­
l arly when the occupant sitting next to it is
not seated properly. The s ide a irbag for the
front passenger seat can be used with proper ­
ly installed chi ld res traints. Please be sure to
read the important information and warnings
whenever us ing a child restraint in a veh icle :
Safety belts
c::;, page 138, A irbag system
c::;, page 147, Child safety ~ page 173.
The side airbag system basically con sists of:
- the e lectronic control module and external
s ide impact sensors
- the two airbags located in the sides of the
front backrests and the two airbags* located
in the rear backrest
- the airbag warning light in the instrument
cluster.
The airbag system is monito red elect ron ica lly
to make certain that it is functioning properly
at all times. Each time you switch on the igni­
tion, the airbag system indicator light will
come on for a few seconds (self diagnostics) .
T he side airbag system supplements the safe­
ty belts and can help to reduce the risk of in ­
jury to the driver's, front and rear passenger's upper torso on t he side of the vehicle that is
struck in a side collision . The airbag deploys
only in s ide impac ts and on ly when the veh icle
acceleration registered by the control u nit is
hi gh enough . If this rate is below the refer­
e nce va lue progr ammed i nto the con trol un it,
the side airbags will not be triggered, even
though the ca r may be badly damaged as a re­
sult of the collision . It is not possible to de­
f ine an a irbag trigger ing range that will cover
eve ry possible angle of impact, since the cir­
cumstances will vary considerably between
one co llision and another . Important facto rs
in clude, for examp le, the natu re (hard o r soft)
of the impacting objec t, the ang le of impact ,
ve hicl e speed, etc. ~
page 1 68, Impor tan t
safety instructions on the side airbag system.
Aside from the ir no rmal safety function, safe­
ty belts wor k to he lp keep the d river or front
passenger in posi tion in the event of a side
Airbag system 167
collision so that the side airbags can provide
protection.
T he airbag system is
not a substi tute fo r your
s af ety belt . Ra ther, it is part o f the over all oc­
cupant restra int system in you r vehicle . A l­
ways remember that the side airbag system
can on ly help to protect yo u if you are wearing
your safety be lt and wearing it proper ly. This
is another reason why you should always wear
your safety be lts, not just because the law re­
quires you to do so c::;,
page 138, General
notes.
It is important to remember that wh ile the
suppleme nta l side airbag system is desig ned
to r educe the likelihood of ser ious injuries,
othe r injur ies, for exampl e, swelling, bru is ing ,
friction bur ns and m ino r abrasions can a lso be
associ ated w ith dep loye d side airbags. Re­
member too, si de a irbags w ill dep loy o nly
once an d only in ce rtain kinds of accidents -
yo ur safety be lts a re a lways there to offer p ro ­
tection .
Vehicle damage, repair costs o r even the lack
of ve hicle damage are not necessarily a n indi ­
cation of over-sensitive or failed airbag activa­
tion. In some coll is ions, both front and side
a irbags may inflate. Remember too, that air­
bags will deploy only once a nd only in cer tain
ki nds of col lisions -you r safety belts a re a l­
ways t he re to offe r protection in those acc i­
dents i n which a irbags are not supposed to
deploy or when they have a lready deployed .
The side airbag system will not deploy:
-when the ignit io n is switched off
- in side co llisions whe n the acceleration
meas ured by t he sensor is too low
- in front-end collisions
- in rear -end co llisions
- in rollove rs .
In some types of accidents the front airbags,
s ide cu rtain airbags and s ide a irbags may be
t rigge red together. .,,. •
•

M N <( I.J "". rl I.O
"' rl
"' rl
-Never use additional seat cushions that
cover the areas where the side airbags
deploy.
- Damage to the original seat covers or
to the seam in the area of the side air­
bag module must always be repaired
immediately by an authorized Audi
dealer .
- Objects between you and the airbag can
increase the risk of injury in an accident
by interfering with the way the airbag
unfolds or by being pushed into you as
the airbag inflates.
- Never place or attach accessories or
other objects (such as cup holders., tel­
ephone brackets, or even large, bulky
objects) on the doors, over or near the
area marked "AIRBAG" on the seat
backrests .
- Such objects and accessories can be­ come dangerous projectiles and cause
injury when the supplemental side air­
bag deploys.
- Never carry any objects or pets in the
deployment space between them and
the airbags or allow children or other
passengers to travel in this position.
- Always use the built-in coat hooks only
for lightweight clothing. Never leave any
heavy or sharp-edged objects in the
pockets that may interfere with side air­
bag deployment and can cause personal
injury in an accident.
- Always prevent the side airbags from be­
ing damaged by heavy objects knocking
against or hitting the sides of the seat­
backs.
- The airbag system can only be triggered
once. If the airbag has been triggered,
the system must be replaced by an au­
thorized Audi dealership.
- Damage (cracks, deep scratches etc.) to
the original seat covers or to the seam in
the area of the side airbag module must
always be repaired immediately by an au­
thorized Audi dealer.
Airbag system 169
-If children are seated improperly, their
risk of inju ry increases in the case of an
accident
Q page 173, Child Safety.
- Never attempt to modify any compo­
nents of the airbag system in any way .
- In a side collision, side airbags will not
function properly if sensors cannot cor­
rectly measure increasing air pressure in­
side the doors when air escapes through
larger, unclosed openings in the door
panel.
- Never drive with interior door trim pan­ els removed.
- Never drive when parts have been re­
moved from the inside door panel and
the openings they leave have not been
properly closed.
- Never drive when loudspeakers in the
doors have been removed unless the
speaker holes have been properly
closed.
- Always make certain that openings are
covered or filled if additional speakers
or other equipment is installed in the
inside door panels.
- Always have work on the doors done by
an authorized Audi dealer or qualified
workshop.
Side curtain airbags
Description of side curtain a irbags
The side curtain airbag system can provide
supplemental protection to properly restrain­
ed occupants.
Fig. 169 Side curta in air bags, driver's side: side curtain
airbag locat ion ....

1 70 Airbag system
The side curtain airbags are located on both
sides of th e interior above the front and rear
side windows ~
fig. 169. They are ident ified
by the word "AIRBAG" on the windshield
frame and the center roof pillar.
The side curtain airbag system supplements
the safety belts and can help to reduce the risk of injury for occupants' heads and uppe r
torso on the side of the vehicle that is struck
in a side collision . The side curtain airbag in­
flates in side impacts and only when the vehi­
cle acceleration registered by the control unit is high enough. If this rate is below the refer­
ence value programmed into the control unit,
the side curtain airbag will not be triggered,
even though the car may be badly damaged as
a result of the collision. It is not possible to
define an airbag triggering range that will
cover every possible angle of impact, since the
circumstances will vary considerably between
one collision and another. Important factors
include, for example, the nature (hard or soft)
of the impacting object, the angle of impact,
vehicle speed, etc.~
page 171, How side cur­
tain airbags work.
Aside from their normal safety function, safe­
ty belts work to help keep the driver or front
passenger in position in the event of a colli­
sion so that the side curtain airbags can pro­
vide protection.
The airbag system is not a substitute for your
safety belt. Rather, it is part of the overall oc­
cupant restraint system in your vehicle. Al­
ways remember that the airbag system can
only help to protect you if you are wearing
your safety belt and wearing it properly. This
is another reason why you should always wear
your safety belts, not just because the law re­
quires you to do so
Q page 138, General
notes.
It is important to remember that while the
side curtain airbag system is designed to help
reduce the likelihood of serious injuries, other
injuries, for example, swelling, bruising, fric ­
tion burns and minor abrasions can also be as­
sociated with these airbags upon deployment. Remember too, these airbags will deploy only once and only in certain kinds of accidents
-
your safety belts are always there to offer pro­
tection.
The side curtain airbag system basically
consists of:
- The electronic control module and external
side impact sensors
- The side curtain airbags above the front and
rear side windows
- The airbag indicator light in the instrument
panel
The airbag system is monitored electronically
to make certain it is functioning properly at all
times. Each time you switch on the ignition,
the airbag system indicator light will come on
for a few seconds (self diagnostics).
The side curtain airbag is not activated:
- if the ignition is switched off,
- in side collisions when the acceleration
measured by the sensor is too low,
- in rear-end collisions.
_&. WARNING
- Safety belts and the airbag system will
only provide protection when occupants
are in the proper seating position
¢page 53, General recommendations.
- If the airbag indicator light Q page 19
comes when the vehicle is being used,
have the system inspected immediately
by your authorized Audi dealer. It is pos­
sible that the airbag will inflate when it
is not supposed to, or will not inflate
when it should.
.

192 Audi pre sense
Audi pre sense
Preventative passenger
protection
A pp lies to veh icles: with Audi pre se nse
Audi pre sense can initiate steps to help pro­
tect vehicle occupants in certain situations.
The functions described depend on equ ipment
installed in your vehicle:
Audi pre sense basic*
The following functions can be triggered in
certain driving situations:
- Tightening of the safety belts (for example,
during heavy braking) : the front safety belts
have reversible belt pretensioners. If a colli­
sion does not occur, the safety belts loosen
slightly and are ready to be tightened again.
- Closing the windows and the sunroof*: the
windows and the sunroof* close leaving a
small open gap.
Audi pre sense basic functions can be trig­
gered at speeds above 20 mph (30 km/h).
Vehicles with Aud i drive select*: the deploy­
ment time is adapted in
Dynamic mode.
Audi pre sense front (vehicles with
adaptive cruise control*)
Audi pre sense front includes the functions in
Audi pre sense basic. In addition, within the
limits of the system, the likelihood of a colli ­
sion with the vehicle immediately ahead is al­
so calculated . If the system senses an immi­
nent collision the following functions can be
tr iggered :
- Braking guard
c::> page 92
- Tightening the safety be lts
- Closing the windows and the sunroof* (leav -
ing a small open gap)
Audi pre sense rear (vehicles with Audi
side assist*)
Audi pre sense rear includes the functions in
Audi pre sense basic. In addition, the likeli­
hood of a rear-end collision with the vehicle
coming from behind is also calcu lated.
If the risk
of a co llision is detected, the following
functions can be triggered:
- Tig htening the safety belts
- Closing the windows and the sunroof* (leav-
ing a small open gap)
Audi pre sense plus*
Audi pre sense plus includes the functions in
Audi pre sense front and Audi pre sense rear.
Error message
Audi pre sense: not available
Preventative passenger protection is not avail­
able. See your authorized Audi dealer immedi­
ately to have the malfunction corrected.
_& WARNING
-=
Audi pre sense cannot overcome the laws
of physics. It cannot prevent a collision. Do
not let the increased safety provided
tempt you to take risks. This will increase
the r isk of a collis ion and serious personal
in juries .
- The sensors cannot always detect all ob­
jects. This increases the risk of a colli­
s10n.
-Aud i pre sense does not detect people or
an im als or objects that are crossing the
veh icle's path
c::> page 86.
-The radar sensor's vis ion can be reduced
by heavy rain, ice, snow, heavy road sp ray
and reflections from guard rails, tunnel
entrances, etc. These and similar condi­
tions can prevent vehicles from being ac ­
curately detected and in some cases they
may not be detected at all.
(D Note
The sensors can be displaced by impacts or
damage to the bumper, wheel housing and
underbody. This can affect the function of
the Audi pre sense system. Have your au­
thorized Audi dealer check to make sure
that the system is working properly.

M N <( (.J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Winter t ire s
When driving in the w inter, your vehicle w ith
all-wheel drive has an advantage, even with
regular tires. In winter road conditions it may
be advisable to mount winter tires (or all-sea­
son tires) for improved driveability and brak­ ing: these tires must be mounted on
a ll fo ur
wheels .
See also c:> page 267, Winter tires.
Tire chain s
Where tire cha ins are mandatory on certain
roads, th is normally a lso applies to vehicles
with all-wheel drive
c> page 268, Snow
chains.
Re placing wh eels/ tire s
Vehicles w ith all-wheel drive must a lways
have tires of the same size. Also avoid tires
with different tread depths. For details see
page
c:> page 260, New tires and replacing
tires and wheels .
Off-Road dri ving ?
Your Audi does not have enough ground clear­
ance to be used as an off-road vehicle. It is
therefore best to avoid rough tracks and un­
even terrain as much as possible. Also refer to
c:>page204.
A WARNING
Always adjust your driving to road and traf­
fic condit ions . Do not let the extra safety
afforded by all-wheel dr ive tempt you into
taking extra risks.
- Although the all-wheel dr ive is very ef­
fec tive, a lways remember that braking
capacity is limited by t ire traction. Yo u
should therefore not dr ive at excessive
speeds on icy or slippery road surfaces.
- On wet road surfaces, be careful not to
drive too fast because the front wheels cou ld begin to slide on top of the water
(aquaplaning). If this sho uld occur, you
will have no warning from a sudden in­
crease in engine speed as with a front­
wheel drive vehicle. A lways drive at
speeds wh ich are suited to the road con­
ditions -risk of c rash.
Int ellig ent technolog y 201
Energy management
Starting ability is optimized
Energy management controls the distribution
of electrical energy and thus optimizes the
availability of electrical energy for starting the engine.
If a vehicle with a conventional energy system
is not d riven for a long per iod of t ime, the bat­
tery is discharged by idling current consumers (e .g. immobilize r). In certain circumstances it
can resu lt in the re be ing insuffic ient energy
available to start the engine.
Intelligent energy management in your vehi­
cl e ha ndles the distribution of e lectr ica l ene r­
gy. Start ing ability is markedly improved and
the life of the battery is extended .
Bas ica lly, energy management consists of
ba tter y dia gno sis, id lin g curr ent manage­
ment
and dynamic ener gy manag ement.
Battery di agnos is
Battery diagnosis continuously determ ines
the state of the batte ry . Sensors determine
battery voltage, battery current and battery
tempe rature. This de termines the curren t
state of cha rge and the power of the battery .
Idling current management
Idling current management reduces energy
consumption while the vehicle is standing .
With the ign ition switched off, it controls the
energy supply to the various electrica l compo ­
nents. Da ta fr om ba ttery d iagnos is is cons id ­
ered.
Depend ing on the batte ry's state of cha rge,
individ ual cons ume rs a re g radually turned off
to prevent excessive discharge o f the battery
and th us maintain star ting capability.
Dynamic energy management
While the vehicle is being dr iven, dynamic e n­
ergy ma nagement distr ibutes the energy gen­
erated a ccord ing to the needs of the individ u-
al components . It regulates consumpt ion, so
that more e lectrical energy is not being used .,.
•
•

M N <( (.J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Vehicl e ca re a nd cl eanin g 213
A WARNING
-Only wash the vehicle when the ignition
is off and follow the instructions from
the car wash operator to reduce the risk of accidents .
- To reduce the r isk of cuts, protect your­
self from sharp metal components when
wash ing the underbody or the inside of
t he wheel housings.
- After washing the vehicle, the braking ef­
fec t may be delayed due to mo isture on
the brake rotors or ice in the winter. The
brakes must be dried first with a few
careful brake applications.
Q) Note
- If you wash t he vehicle in an automatic
car wash, yo u must retrac t the rear spoil­
er if necessary, and fo ld the exter ior mir­
rors in to reduce the risk of damage.
Power folding exterior mirrors* must on­
l y be folded in and out using the power
fo ld ing funct ion.
- To prevent paint damage, do not wash
the veh icle in direct sunlight. -
To reduce the risk of damage to the sur­
face, do not use insect removing spong­
es, kitchen sponges or similar items.
- Matte finish painted vehicle compo­
nents:
- To reduce the risk of damage to the surface, do not use polishing agents or hard wax.
- Never use car wash cycles that apply protective wax.
It can destroy the
matte fi nish effect.
- Do not place any stickers or magnet ic
signs on vehicle parts painted w ith
matte fi nish paint. The paint cou ld be
damaged when the stickers o r magnets
are removed.
@ For the sake of the environment
Only wash the vehi cle in facilities spec ial ly
designed for that purpose . This will red uce
the risk of dirty water contam inated with
oil from entering the sewer system.
Cleaning and care information
When cleaning and caring for individua l vehi ­
cle components, refer to the follow ing tab le.
The information contained there is s imply rec­
ommendations. For quest ions or for compo- nents
that are not listed, refer to an author­
ized Audi dealer or a qualified workshop. Also
follow the information found inc>,& .
Cle aning e xte rior
Component Situation Solution
W ip er bl ade s
Dirty c> page 49, Cleaning windshield wiper blades
Headlights/ Dirty Soft
sponge with a mild soap solution al
tail lights
S ensor s/
Dirty Sensors: soft cloth with a solvent-free cleaning product
cam era l enses Camera lenses: soft cloth with an alcohol-free cleaning
so lution
Snow/ice Hand brush/solvent-free de-icing spray
Whe els Road sa lt Water
Brake dust Acid-free special cleaning solution
Ex haust t ail Road sa lt Water, cleaning solut
ion suitable for sta inless steel, if
pipe s necessary
•
•

232 Check ing and filling
Before you check anything in the engine com­
partment,
a lways r ea d and heed all WARN­
INGS ¢ A in Working in the engine compart­
ment on page 225.
• Park your vehicle on a level surface.
• Switch
off the ignition .
• Read the eng ine coolant leve l from the cool­
ant expansion tank
c> fig. 196, c> page 22 7,
fig. 193. With a cold eng ine, the coolant
level should be between the "min" and
"max" markings. When the engine is warm,
the leve l may be slightly above the "max"
ma rk ing.
The location of the coolant expans ion tank
can be seen in the engine compartment illus­
tration ¢
page 22 7.
To obtain an accurate reading, the engine
must be sw itched
off.
The expans ion tank in your vehicle is equipped
with an electric coolant level sensor.
When the coo lant level is too low, the warning
light in the Auto-Check System ¢ page l 6 will
i l luminate unti l yo u add coolant and the level
has been restored to normal. Even though
there is an electric coolant level senso r, we
still recommend you check the coolant leve l
from time to time .
Coolant loss
Coolant loss may indicate a lea k in the cooling
system. In the event of coolant loss, the cool­
ing system should be inspected immediately
by your author ized Audi dealer. It is not
enough merely to add coolant.
In a
sealed system, losses can occur only if
the boiling point of the coolant is exceeded as
a result of overheat ing.
A WARNING
T he cooling system is unde r pr essure and
c an get ve ry hot. Reduce t he risk of s cald­
ing from hot coolant by followi ng these
steps .
- T urn
off the engine and allow it to cool
dow n. -
Protect your face, han ds and arms from
escaping flu id and steam by cover ing the
cap with a large, thick rag.
- Tu rn the cap slowly and very care fully in
a counte r-clockwise direct ion while ap­
plying lig ht, downward pressure on the
top of the cap.
- To avo id being burned, do not sp ill anti­
freeze or coolant on the exhaust system
or hot engine par ts. Under certa in cond i­
tions, th e ethylen e glyco l in engine coo l­
a nt can catch fire.
(D Note
Do not add a ny type o f radiator leak sea l­
ant to your veh icle's engine coolant. Add­
i ng radiator r epa ir fluid may adv erse ly af­
fe ct the funct io n and perfo rma nce of you r
co oling syste m and could result in damage
not covered by your New Veh icle Limi ted
War ran ty.
Adding coolant
Be very careful when adding engine coolant.
Befo re you check anyth ing in the eng ine com­
partment,
alway s read and heed all WARN·
INGS ¢ A in Working in the engine compart­
ment on page 225.
• Requirement: The re must be a r esidua l
amount of coolant in the e xpansion ta nk
¢(D.
•Tur no ff the engine.
• Le t the engine cool down.
• Place a thick rag ove r th e coo lant expansion
tank
¢ page 231, fig. 196 and carefully
twist the cap co unte r-clockwise c> &_ .
• Add coo lant m ixed in the correct rat io
¢ page 231, Coolant up to the MAX mark­
ing.
• Make s ure that the fl uid leve l remains sta-
b le. Add more coo la nt if necessary.
• Twis t the cap o n again
tightly.
Replacement engine coo la nt must confo rm to
exact spec ificat ions
¢ page 2 31, Coolant. .,.

M N <( I.J "". rl I.O
"' rl
"' rl
Tire pressure indicator appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
Fig. 205 Display: underinflation warning
Fig. 206 Display: System malfunction
Using the ABS sensors, the tire pressure moni­
toring system compares the tire tread circum­ ference and vibration characteristics of the in­
dividual tires. If the pressure decreases in one
or more tires, this is indicated in the instru­
ment cluster with a warning symbol
rD] and a
message
c:> fig . 205.
The tire pressure monitoring system must be
reset via MMI each time the pressures are ad­
justed (e.g. when switching between partial
and fu ll load pressure) or after changing or re­
placing a tire on your vehicle
c:> page272 . The
TPMS indicator only monitors the tire pres­
sure that you have previously stored. You can
find the recommended tire pressures for your
vehicle on the label on driver's side 8-pillar
c:>page247.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the tire pressure in one or more tires is too
low,
Tires and wheels 2 71
- the tire has structural damage,
- the tire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
c:>poge272.
- the spare tire* is mounted .
Warning symbols
[I] Loss of pressure in at least one tire¢.& .
Check the tire or tires and replace or repair if
necessary. The indicator light
rD] in the instru­
ment cluster also illuminates <=:>
page 12.
Check/correct the pressures of all four tires
and resetTPMS via MMI.
l!I (Tire Pressure Mon itoring System) Tire
pressure! System malfunction .
Ifljl appears
after switching the ignition on or while driving
¢
fig. 206 and the indicator light rD] in the in­
strument cluster blinks for approximately one
minute and then stays on, there is a system
malfunction. Attempt to store the correct tire
pressure
c:> page 272. If the indicator light
does not turn off or if it turns on shortly
thereafter, immediately drive your vehicle to
an authorized Audi dealer or authorized repair
facility to have the malfunction corrected.
_& WARNING
- If the tire pressure indicator appears in
the instrument cluster display, one or
more of your tires is significantly under­
inflated. Reduce your speed immediately
and avoid any hard steering or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures. In­
flate the tire pressure to the proper pres­
sure as indicated on the vehicle's tire
pressure label<=:>
page 247 . Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability.
- The driver is responsible for maintaining
the correct tire pressures. You must check the tire pressures regularly.
.