2015 AUDI S3 Owners Manual

M N
0 > co ,...., \!) ..,.,
M ..,., ,....,
A WARNING ,~
Rearward-facing ch ild restraints:
-A chi ld in a rearward-facing child safety
seat installed on the front passenger
seat will be ser iously injured and can be
killed if the front airbag inflates -even
with an Advanced Airbag System .
- The inflating a irbag w ill hit the child
safety seat or infant carrier w ith great
force and w ill smash the ch ild safety seat
and child against the backrest, cente r
armrest, door or roo f.
- Always be especially caref ul if you must
install a rearwa rd fa cing child safety seat
on the front passenge r sea t in exception­
al circumstances .
- Make su re that the
PASSENGER AIR BAG
OFF
light comes on and s tays on all the
time whenever the ignition is switched
on .
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, immedi­
ately install the rea r-facing chi ld safety
seat in a rear seating position and have
the a irbag system inspected by you r Audi
dealer.
Activating the convertible locking retractor
Use the convertible locking retractor to se­
cure a child restraint.
Always heed the child safety seat ma nufactur­
er's instructions when install ing a chi ld re­
straint in your vehicle . To activate t he conver ­
tible locking retracto r:
.,. Place the child restraint on a seat, prefera­
bly on the rear sea t.
.,. Slow ly pull the be lt
all the way out .
.. Route it around or through the ch ild re­
st ra int be lt path ¢&, .
.,. Push the child safety seat dow n with your
f ull weight to ge t the safety belt really t ight.
.,. Insert the be lt tongue into the buckle for
that seating position .
Child Safet y 183
.,. Guide the sa fe ty be lt back into the retractor
until the be lt lies flat and sn ug on the child
safety seat .
.,. You shou ld hear a "clicking" noise as the
be lt winds back into the iner tia ree l. Test the
convert ible lock ing retractor by pulling on
the belt. You sho uld no lo nger be able to
pull the be lt out of the retracto r. T he con­
ver tible locking re trac to r i s now ac tiva ted .
.,. Mak e s ure t hat t he red release b utton is fac ­
ing away from the child rest rain t so t hat i t
can be unbuckled q uic kly .
.. Pull on the belt to make sure the safety be lt
is properly tight and fastened so that the
seat cannot move forward or sideways more
than one inch (2 .5 cm).
A WARNING
Using the wrong child restraint o r an im­
p roperly installed chi ld restraint can cause
serious pe rsonal injury or death in a crash.
- Always ma ke sure that the safe ty belt re-
tracto r is loc ked when insta lling a child
safety seat. An unlocked safety belt re­
tracto r can not hold the child safety seat
in place dur ing no rma l driving o r in a
cras h.
- Always buckle the child sa fe ty seat firmly
in place even i f a ch ild is not sitt ing in it.
A loose child safety seat can fly aroun d
during a sudden stop or in a crash .
- Always ma ke s ure the seat backrest to
which the child restraint is installed is in
an upright pos ition and securely latched
into place and can not fold forward . Oth­
erw ise, the seatback with the child safety
seat attached to it could fly forward in
the ev ent of an accident o r othe r emer­
gency situatio n.
- Always read a nd heed al l WAR NINGS
wheneve r us ing a child restrained in ave­
hicle is being used ¢
page 170. Special
pre cau tions apply whe n inst alling a child
safety sea t on the fron t passenger seat
¢ page 146, Child restraints on the front
seat -some important things to know.
-
•
•
•

184 Child Saf ety
Deactivating the convertible locking
retractor
The convertible locking retractor for child re­
straints will be deactivated automatically when the belt is wound all the way back into the retractor .
.,. Press the red button on the safe ty belt buck­
le. The be lt tongue w ill pop out of the buck­
le .
.. Guide the safety be lt all the way back into
its stowed position .
A lways le t the safety bel t retract comp lete ly
into its stowed posit ion . The sa fety belt can
now be used as an ordinary safety belt with ­
out the convert ib le locking ret ractor for chi ld
restra ints.
If the convertible locking retracto r shou ld be
activated inadvertently, the safety belt m ust
be unfastened and guided comp letely back in­
to its stowed pos ition to deactivate th is fea­
ture. If the convertib le locki ng retractor is not
deactivated, the safety be lt will gradually be­
come tighter a nd u ncomfo rtable to wea r.
A WARNING
Imprope rly insta lled child saf ety seats in­
crease t he risk of ser ious personal inju ry
a n d death in a collision .
- Never unfaste n the safety belt to deacti­
vate the convert ible lo cking re tr actor fo r
ch ild rest rain ts while the veh icle is mov­
ing. You would not be res trained and
cou ld be seriously injured in an accident.
- Always re ad and heed all WARN INGS
whenever using a child rest rained in ave ­
hicle is being used
¢page 170. Special
precautions apply when installing a ch ild
safety seat on the front passenge r seat
¢ page 146, Child restraints on the front
seat -some important things to know.
LATCH Lower
anchorages and tethers
for children
Child Restraint System anchors and how
are they related to child safety
T o p rov ide a simple r and more practicable way
to a ttach the child restra int on t he vehi cle
sea t, Federal regulat ions re quire spe cial lowe r
anchorages in vehicles and devices on new
c h ild restraints to attach to the vehicle ancho­
rages.
T he comb inat io n of th e tether anc horages and
the lowe r anchorages is now genera lly c alled
t h e
LATCH system fo r "Lower Anchorages and
T ethers for Child ren."
F o rward-f ac ing ch ild res trai nts ma nufacture d
after September 1, 1999, are req uired by U .S .
f ede ra l regu lations to comply with new child
head movement performance req uirements.
These new performance req uirements make a
tether necessary on most new child seats.
Installing a child restraint that requires a top
tethe r without one can seriously impair the
performance of the c hild restra int and its abil­
ity to protect the child in a coll is ion. Insta lling
a chi ld restrai nt that requires a top tether
without the top tether may be a violat ion of
state law.
Child rest raint manufacturers offer LATCH
lower anchorages on their child seats w ith
hook-on or push-on connectors attached to
adjustable straps .
In add ition to the LATCH lower anchorages,
t h ese chi ld restraint systems usually require
t h e use of tethe r straps to he lp keep the ch ild
rest raint fi rmly in place.
A WARNING
-Imp roper installat ion of ch ild restra ints
will i ncrease the r is k of injury a nd dea th i n
a cr ash.
-

M N
0 > co
rl I.O
"' M
"' rl
-Always follow the instructions provid ed
by the manufacturer of the ch i Ld re ­
straint you intend to install i n your veh i­
cle .
- Never install a child restraint without a
properly attached top tether strap if the
child restraint manufacturer's inst ruc ­
t ions requ ire the top tether strap to be
used .
- Improper use of ch ild restra int LATCH
lower anchorage points can lead to injury
in a collis ion. The LA TCH lower anchorage
points a re designed to w ithstand only
those loads imposed by correct ly fit ted
child restraints.
- Never mount two chi ld restraint systems
on one LA TCH lower anchorage point .
- Never secure o r attach any luggage or
other i tem to the LATC H lower anchorag­
es .
{i) Tips
-In Canada , the terms "top tether " with
"lowe r universa l anchorages " (or "lowe r
universa l anchorage bars") are used to
desc ribe the system .
- In ot her countries, the term "ISO FIX " is
u sed to describe the lower anchorages .
Location
Fig . 144 Sch ematic overv iew : LA TCH an cho rage point
l o ca tion s
> 0)
"'
The illustration shows the seating locations in
your veh icle which are equ ipped w ith the low­
e r anchorages system.
Child S afety 185
Description
The lower anchorage positions are marked
for quick locating .
Fig . 14 5 Lower an chor ag es, cove rs mar ked
Fig. 146 Rear s eats: low er an cho rage bra cket lo ca tion s
Low er anchorag es
The circular markings on the rear seat he lp
you to ident ify the location of lower ancho rag­
es for the two outboard seating posi tions
¢ fig . 145. The LATCH lower universal anchor­
age attachm ent points are b etween the rear
seatback and rear seat cush ion .
R emove the covers
¢ fig . 145 to access the
lower anchor age attachment points .
T he lower anc ho rage attachment po ints are
vis ible ~
fig. 146.
Lower anchorage s secure the chi ld rest rai nt in
the seat without using the vehicle's safety
belts . Anchorages provide a secure and easy­
to-use attachment and minimize the possibili­
ty of improper child restra int installa tion.
All child restraints manufactured after Sep­
tember 1, 2002 , m ust have lower anchorage
attachments for the
LATCH system.
Please remembe r that the lower anchorage
poin ts are only intended for installat ion and
Iii>

186 Child Saf ety
attachment of child restraints specifically cer­
tified for use with
LATCH low er anchorages.
Ch ild restra ints that are not equipped with the
lower anchorage attachments can still be in­
stalled in comp liance with the child restrain t
manufacturer's instruct ions on using vehicle
safety belts .
A WARNING
Improper use of LATCH lower anchorages
can ca u se serio us pe rsonal inju ry i n an ac­
c ident .
- Always ca refully fo llow the c hild re­
st raints manuf acturer's inst ru cti ons for
proper ins tallat ion of the child rest rain t
and proper use of the lowe r anchorages
or safety be lts in your vehicle .
- Never secure or attach any l uggage or
other items to the
LATCH lower ancho ­
rages.
- Always read and heed the impor tant in ­
format ion about child restraints in this
chapter and WARNINGS
~ page 170 ,
Child Safety.
Installing a child restraint with LATCH
lower anchorages
App lies to vehicles: with Top Tether
Whenever you install a child restraint always
follow the child restrain t manufacturer's in­
structions.
F ig . 14 7 Lower a nch orage s: p rope r m ou ntin g
Mounting
~ Make sure the seatback of the rear seat
bench is in the upr ight position and se curely
l atched in pl ace.
~ Attach both hook -on connectors with the
spring catch release on the child safety seat
onto the LA TCH lower anchorage so that the
connectors lock into place <=>
fig. 147.
~Pullon the connector attachments to make
sure they a re properly attached to the LATC H
lower ancho rage .
~ Pull straps tight fo llow ing the child r estraint
manufact urer's inst ruct io ns .
Releasing
~ Loose n the tension on the straps following
the child restra int manufacturer's instruc ­
tions .
~ Depress the spr ing catches to releas e the
anchorage hooks from the lowe r an chorag­
es.
Remember: Use te ther straps to help keep the
c hi ld restra int fi rm ly in place.
A WARNING
I m proper use of the LATCH system can i n­
crease the risk o f serious pe rsonal in jury
and death in a n accident.
- T hese an chors were deve lope d on ly for
chi ld safe ty seats using the " LA TC H" sys ­
tem .
- N ever at tach othe r ch ild safety sea ts,
be lts or o ther objects to these anchors .
- Always ma ke su re tha t you hear a click
when latch ing the seat in place . If you do
not hear a click t he seat is not secu re and
could
fly forwa rd and hit the inter ior of
the vehicle, or be e jected from the veh i­
cle.
A WARNING
-Improper installat ion of child restra ints
will i ncrease the r isk of injury in an acci­
dent.
- Always follow the chi ld restraint system
manufacturer's inst ruct ions for prope r
installa tion of the c hild restra int system
a nd p roper use of tether st raps as well as
the lower a nchorages or safety bel ts in
your veh icle.
~

M N
0 > co
rl I.O
"' M
"' rl
-Always read and heed the important in­
formation and WARNINGS about child
safety and the installation of child re­
straint systems
c:> page 170, Child Safe­
ty.
Tether anchors and tether straps
Fig . 14 8 Te th er ancho rs: re cess flap s be hind the re ar
sea tback s
The tether anchors for the rear seating posi­
tions are located in recesses in the rear win­
dow she lf
c:> fig. 148
A tether is a straight or V -sha ped strap that
attaches the top part of a child res traint to
specia l anchorage poi nts in the veh icle.
T he purpose of the tether is to reduce the for­
ward movement of the c hild restra int in a
crash, in o rder to help reduce the r isk of head
i n jury that could be caused by striki ng the ve­
hi cle inter io r.
Forward facing child restraints manufactured
after September 1, 1999 , are required by U .S .
federal regulations to comp ly with new c hild
h ead movement perform ance requirements.
These new per formance requ irements make a
tether necessary on most new child safety
seats.
A WARNING
Improper insta llation of chi ld restraints
w ill increase the risk of injury and death in
a crash.
- Always fo llow the instructions prov ided
by the manufacturer of the ch ild re­
straint you intend to install in your Audi.
Child S afety 18 7
-Improper use of child restraint anchors
(including tether anchors) can lead to in­
jury in a collision. The anchors are de· sig ned to withstand only those loads im­
posed by correctly fitted child restrain ts .
- Never mount two child restra int systems
on one LATC H lowe r anchor point .
- Never attach two child restraint systems
to one tether st rap or tethe r anchorage .
- Never attach a tether strap to a t ie-down
ho ok in the luggage compartment.
- Never use child restraint tether ancho­
rages to secure safety belts or other
kinds of occupant rest raints.
- Never secure or attach any luggage or
o ther items to the LATCH lower ancho­
rages or to the tet her anchors.
- If you must install a rearward fac ing
child safety seat on the fro nt passenger
seat because of e xceptional c ircumstan­
ces and t he
PASSENGER AIR BAG OFF
lig ht does not come o n and stay on, im­
medi ately ins tall th e rear-fac ing ch ild
safety sea t in a rear se atin g position and
have the airbag system inspected by your
Au di dea le r.
Installing the upper tether strap on the
anchorage
F ig . 14 9 Tet her st ra p: prop er rou ting a nd m ou ntin g
Installing the tether strap
... Release or deploy the tet her st rap on the
child res traint accord ing to the child re ­
s tr aint manufacture r's ins tructions .
... Gu ide the upper tether strap
under th e rear
head restraint
c:> fig. 149 (ra ise the head re-
stra int if ne cessary) . "'

188 Child Saf ety
• Tilt the recess flap up to expose the anchor
bracket.
• Attach the tether strap anchorage hook into
the opening of the tether anchorage.
• Pull on the tether strap hook so that the
spring catch of the hook engages.
• Tighten the tether strap firmly followi ng the
ch ild restra int manufacturer's inst ruct ions .
Releasing the tethe r strap
• Loosen the tens ion following the child re­
stra int manufacturer's instructions.
• Depress the spring catc h on the hook and re­
lease it from the anchorage.
(D Note
If you leave the child restraint with the
t ether strap firmly insta lled for several
days, this cou ld leave a mar k on the up­
h olste ry on t he seat cush ion a nd ba ckrest
in the are a whe re the te ther s tra p w as in­
s t alled. The uphols tery wo uld also be per­
manently stretched around the tethe r
strap . This applies especially to leather
seats .
Using tether straps on rearward-facing
child restraints
Cur rently, few rear-facing child rest raint sys­
tems come w ith a tethe r. Pl ease read and
h eed the child res traint system manufactur­
e r's ins tructions ca ref ully to dete rm ine how to
p roperly insta ll the tethe r.
& WARNING
-
A child in a rea rward -facing child safety
seat insta lled on the front passenger seat
w ill be seriously injured and can be k illed if
the front a irbag inflates -
even wit h an Ad­
vanced Airbag System.
- The inflating a irbag wi ll hit the child
safety seat or infant carrier wit h great
force and w ill smash the c hild safety seat
and child against the backrest, ce nte r
armr est, or door.
- If you must install a rearward faci ng
child safety seat on the front passenger seat because of exceptiona
l cir cumstan ­
ces and the
PASSENGER AIR BAG OFF
lig ht does not come on and stay on, im­
mediately insta ll the rear-fac ing c hild
safety seat i n a rear seat ing position and
have th e air bag system i nsp ecte d by your
Aud i de aler.
Additional Information
Sources of information about child
restraints and their use
There are a number of sources of add itiona l
informat ion abo ut child rest ra int selection, in­
sta llation and use:
NHTSA advises that the best child safety seat
is the one that fits your ch ild and fits in your
vehicle, and that yo u will use correct ly and
co nsist ently .
Try before yo u buy!
U.S National Highway Traffic Safet y Admin­
istration
Tel.: 1-888-327-4236 (TIY: 1-800-424-9153)
www.nhtsa.gov
National SAFE KIDS Campa ign
Tel.: (202) 662-0600
www.safek ids.org
Safet y BeltSafe U.S.A
Tel.: (800) 745-SAFE (English)
Tel.: (800) 747-SANO (Spanish)
www.ca rseat.org
Transport Canada Information Centre
T el.: 1-800-333-0371 o r ca ll
1-613 -998 -8616 if you are in the Ottawa area
http://www.tc.gc.ca/eng/roadsafety/
men u.h tm
Audi Customer Relations
Tel.: (800) 822-2834

M N
0 > co ,...., \!) 1.1'1
M 1.1'1 ,....,
Smart Technology
Information about
data recorded by
vehicle control
modules
Your vehicle is not equipped with a crash data
recorder. This device is installed by some vehi­
cle manufacturers to record data about crash­
es so that it can be analy zed later . Crash data
recorders are also called "Event Data Record­
ers ( EDR)" .
In some legal jurisdictions, it is not permitted
to access or download data recorded by pre­
installed crash data recorders in order to eval­
uate a crash without clear consent of the vehi ­
cle owner .
Your vehicle is not equipped with a crash data recorder. However it does contain a variety of
electronic control modules for various vehicle
systems such as engine function, exhaust
treatment or airbags and safety belts .
These electronic control modules record vehi­ cle data during normal driving for diagnosis
and repair purposes . The recording capability
of the electronic control modules is limited to
data only- no sound is recorded.
If the control
module detects a system ma lfunction or other
change in status, a very limited amount of da ­
ta is recorded for an extremely small period of
time . Data that is recorded in such a case may
include vehicle speed, d riving direction, the
load on the brakes and head restraints and
performance in the event of an acciden t or
other change in status . The stored data can
only be read or downloaded with special devi­
ces.
Electronic stabilization
control (ESC)
Description
The Electronic Stabilization Control (ESC) con­
tr ibutes to driver safety. It reduces the risk of
slipp ing and improves driving stability. ESC
Smart Technolog y 189
detects critical situations such as the vehicle
oversteering and understeering or the wheels
are spinning . The vehicle is stabilized by ap­
plying the brakes or reducing engine torque.
Once the ESC is activated, the indicator light
m blinks in the instrument cluster .
The following systems are integrated in the
ESC:
Anti-lock braking system (ABS )
ABS prevents the whee ls from locking when
braking. The vehicle can still be steered even
during hard braking. Apply steady pressure to
the brake pedal. Do not pump the pedal. A
pulsing in the brake peda l indicates that the
system is acting to stabilize the vehicle.
Brake assi st sys tem
The brake assist system can decrease braking
distance. It increases braking power when the
driver presses the brake pedal quickly in emer­
gency situations. You must press and hold the brake pedal until the dangerous situation is
over . In vehicles with adaptive cruise control*,
the brake assist system is more sensit ive if the
distance detected to the vehicle ahead is too
small.
Anti-slip regulation (ASR)
ASR reduces engine power when the drive
wheels begin spinning and adapts the force to
the road conditions . This makes it easier to
start , accelerate and dr ive up inclines .
Electronic differential lock (EDL)
The EDL brakes wheels that are spinning and
transfers the drive power to the other drive
wheel or wheels if the vehicle is equ ipped with
all wheel drive*). This function is not available
at higher speeds .
In extreme cases, EDL automatically switches
off to keep the brake on the braked wheel
from overheating . The vehicle is still working
correctly. EDL will switch on aga in automat i­
cally when cond itions have returned to nor-
mal. .,..
•
•
•

190 Smart Technology
Steering r ecommendat ion
The ESC helps to stabilize the vehi cle by
changing the steering torque.
Select ive wh eel torqu e co ntrol
Select ive wheel torque control is used when
driving on curves . The front wheel on the in ­
side of the curve or both wheels on the inside
of the curve are braked selective ly as needed.
Th is a llows more precise driv ing in c urves.
Automatic post -collision braking system
The "Automatic post-collision braking system"
can he lp to reduce the risk of sliding and of
other coll is ions after an acc ident. If the airbag
control mod ule detects a collision above acer­
tain vehicle speed, the vehicle is braked by the
ESC.
The vehicle does not brake automatically if:
- the driver presses the accelerator pedal , or
- the braking fo rce genera ted by the pressed
brake pedal is greater than the braking force
that would be initiated by the system, or
- the ESC, the brake system or the vehicle
electrical system are not functioning .
A WARNING ,.
- The ESC and its integrated systems can­
not overcome the lim its posed by natural
physical laws. This is especia lly impor­
tant on s lippery or wet roads. If the sys-
Switching on /off
terns begin acting to stabilize your vehi­
cle, you should immediately a lter your
speed to match the road and traffic con­
ditions . Do not let the increased safety
provided tempt you into taking r isks .
This could increase your risk of a co lli­
sion .
- Please note the r isk of a coll is ion increas­
es when driving fast, especially through
curves and o n slippe ry or wet roads, and
when dr iv ing too close to objects ahead.
The ESC and i ts integrated systems can­
not a lways p revent collisions -there is
still a risk of accidents!
- Press the acce lerator pedal caref ully
when acce lerating on even, slippery sur­
faces such as ice and snow. The drive wheels can spin even when these control
systems are installed and this can affect
driving stability and increase the risk of a
coll is io n.
(D Tips
- ABS and ASR only function correctly
when all four wheels are equ ipped w ith
identical t ires . Different t ire sizes can
lead to a reduction in engine power.
- You may hear noises when the systems
descr ibed are working .
- If the
DJ or [IJ indicator light appears,
there may be a malfunction¢
page 22.
E SC turns on automatically when you start the engine .
Fig. 1 50 Upper c ente r conso le : ESC but to n
The ESC is designed to funct ion in levels . De­
pending on the level that is selected, the sta­
bilization funct io n of the ESC is lim ited or
swit ched off . The amoun t of stabilization con ­
tro l will differ depending on t he level.
In the follow ing unusual situations it may
make sense to switch the ESC sport mode on
to allow the wheels to sp in:
- Rocking the vehicle to free it when it is stuck
- Driving in deep snow or on loose ground
ll>