2015 AUDI RS5 CABRIOLET radio

34 Openin g and clo sing
locking and unlocking with convenience
key
Appl ies t o vehicles : wit h convenience key
The doors ond the rear lid can be unlocked
and locked without operating the master key.
Fig . 22 Doo r hand le: lock ing the v ehi cle
Unlo cking v ehicl e
.. Take hold of the door handle . The door is un-
locked automatica lly.
.. Pull the handle to open the door.
locking vehi cle
.. Move the selector lever to the P position,
otherwise the veh icle cannot be locked .
.. To lock the vehicle , close the door and touch
the sensor in the door hand le
onc e ¢fig. 22
¢ A in G eneral description on page 30. Do
not reach inside the door handle .
The vehicle can be locked and unlocked at any
door . The remote control key cannot be more
than 1.5 m away from the door hand le. It
makes no difference whether the mas ter key
is in your jacket pocket or in your brief case.
If you grip the door handle while locking, this
can adversely affect the locking function. I t is not possible to re-open the door for a
brief period direct ly after closing it. This al­
lows you to ens ure that the doors are properly
locked.
I t depends on the settings in the radio or
MM!* whether the e ntire vehicle is unlocked
or one of the doors¢
page 35 .
A WARNING
-Read and follow all WARNINGS ¢.&. in
General description on page 30 .
(D Tips
If your vehicle has been standing for an ex­
tended period, please note the following:
- The proximity sensors are deactivated af-
ter a few days to save power. You then
have to pull on the door handle once to
unlock the vehicle and a second t ime to
open the vehicle .
- To prevent the battery from being d is­
charged and to preserve your vehicle's
ability to start for as long as possib le,
the energy management system gradu­ ally switches off unne cessary conven­
ience func tions.
It is possib le that you
w ill not be able to unloc k your vehicle us­
ing these convenience funct ions.
- For Declara tion of Complian ce to Unite d
States FCC and Ind ustry Canada reg ula ­
tions ¢
page 267.
locking and unlocking the vehicle from
inside
F ig . 23 D rive r's doo r: pow er lock ing sw it c h
.. Press the button@ to lock the vehicle¢.&, .
.. Press the button @ to unlock the vehicle
¢fig.23.
If you lock the vehicle using the power loc king
switch, p lease note the following:
- If a door is open, the veh icle cannot be
loc ked using the power lock ing system
sw itch.

"' N
a: LL co
rl I.O
"' rl
"' rl
- You cannot open the doors or the rear lid
from the outside (increased security, for ex­
amp le when you are stopped at a red light).
- The diodes in the power locking switc h illu­
minate when all the doors are closed and
locked.
- You can unlock and open the doors from the
i nside by pul ling on the door hand le .
- If you have a crash and the airbag is activat ­
ed , the doors automatically un lock .
_& WARNING
- The power locking switch works with the
ignition off and automatically locks the
entire vehicle when it is actuated .
- On a vehicle locked from the outside the
power locking system switch is inopera­
t ive.
- locked doors make it more difficult for
emergency workers to get into the vehi­
cle, which puts lives at risk . Do not leave
anyone behind in the veh icle, especially
children .
@ Tips
Your vehicle is locked automatically at a
speed of
9 mph (15 km/h) (Auto lock)
Q page 30. You can un lock the vehicle
aga in using the opening function in the
powe r locking system switch~-
Setting power locking
In the radio/MM!*, you can set which doors
the centrol locking system will unlock .
~ Select: I CAR I function button > C entral lock­
ing .
Or
~ Select: ~IC_A_R~I funct ion button> Car systems *
control button > Vehicle settings > (C entral
locking )* .
Sin gle door unlocki ng /Unl ock door s* -
you
can specify which doors u nlock when you open
the vehicle .
- Se lecting
off / All and pressing the Ii button
on the remote control key unlocks the entire
vehicle.
Opening and clo sin g 35
- Select ing o n/Dri ver and pressing the~ but­
ton on the remote control key once u nlocks
only the driver's door . In vehicles w ith a con ­
ven ience key*, only the door whose handle
you pull w ill unlock . If you press the @! but­
ton tw ice, the entire vehicle will u nlock . If
you press the [@] button, t he e ntire ve hicle
w ill always lock .
Luggage comp. lock /Lock e xterio r trunk han ­
dl e -
If you select On , you can no longer open
the luggage compartment us ing the rear lid
hand le
Q page 36, fig. 26. In this case, the
r ear lid can be opened with the
l~I bu tton on
the maste r key
Q poge 33, fig. 21 .
Tone when lock ing -if you select On , a tone
will sound when yo u loc k the vehicle .
Auto Lock /lock when dr iving -if you select
On, the entire ve hicle w ill lock automatica lly
whe n the speed reaches
9 mph ( lS km/h) .
Emergency locking
Fig. 2 4 D river 's doo r: lock cylinder
Fi g. 25 Fro nt pass eng er 's doo r: em erg en cy lock
If the cent ral locking system malfunct ions,
you must unlock/lock the doo rs separate ly us ­
ing the emergency key or the mechanical key . ..,.

36 Opening and closing
Unlocking/locking the driver's door with
the mechanical key
• Remove the mechanical key ¢ page 32.
• To unlock the driver's door, turn the key to
the open position@¢
fig. 24.
• To lock the driver's door, move the selector
lever to the P position (automatic transmis ­
s ion) and turn the key
once to the close posi­
tion
@ ¢.& in General description on
page
30.
Locking the front passenger's door with
the mechanical key
The emergency lock is located on the rear side
of the front passenger's door. It is only visible
when the doo r is open.
• Remove the mechanical key ¢
page 32 .
• Pull the cover cap out of the opening
¢ fig. 25.
• Inse rt the key in the inside slot and turn it
all the way to the right.
Once the front passenger's door has been
closed, you cannot open it again from the out­
side. The door can be opened from the inside
by pulling the door handle.
A WARNING
Read and follow a ll WARNINGS ¢ A in
General description on page
30.
(_D Tips
After the ignition is switched on, the pow­
er locking system switch is enab led .
Electronic immobilizer
The immobilizer prevents your vehicle from
being started by unauthorized persons .
-
Inside the key there is a computer chip . This
ch ip automatically activates/deactivates the
e lectronic immobilizer.
Applies to vehicles with ignition lock:
The electron ic immobilizer deactivates auto­
mat ica lly when you insert the remote contro l
key into the ignition lock.
It activates again a
utomatical ly when you remove the remote
control key from the ignition lock.
Applies to vehicles with convenience key:
If the remote control key is located inside the
vehicle and you press the
I START ENGINE ST OPI button, the electronic
immobilizer deactivates automatica lly. If you
switch the ignition off and remove the remote
control key from the vehicle, the electronic
immobilizer activates again automatically.
A WARNING
--
Always take the key with you when you
leave the vehicle. The key can disarm the
electronic engine immobilizer and permit
an unauthorized person to start the engine
and enable operation of the vehicle sys­
tems such as power window or power sun­
roof leading to se rious personal injury.
(D Tips
- The vehicle cannot be started if an una u­
thorized key is used. The vehicle may not
start if another radio device s uch as a key
for another vehicle or a transponder is
located on the key ring.
- For Declaration of Compliance to United
States FCC and Industry Canada reg ula­
tions ¢
page 267.
Rear lid
Opening /closing rear lid
Fig. 26 Rea r lid: ha nd le

"' N
a: LL co
rl I.O
"' rl
"' rl
Clear vision Lights
Switching the lights on and off
F ig . 55 Instrument pane l: headlight control switch
Light switch ·'t/,·
i
Turn the switch c> fig . 55 to the correspond ing
position . When the lights are switched on, the
:oo: symbol turns on.
0 • The lights are off or the dayt ime running
lights are on:
- USA model s: The daytime running lights are
activated when the light sw itch
c> fig . 55 is
in the
O position or the AUTO position (only
in daylight conditions). The daytime running
lights function can be turned on and off in
the radio or MMI * menu
Exterior lighting
¢page 52, c> &_ .
-Canada model s: The daytime runn ing lights
are activated when the light sw itch ¢
fig. 55
is i n the O position, :oo: position or the AUTO
pos it io n (on ly in daylight cond itions) . The
daytime running lights function canno t be
turned off¢&. .
AUTO* -Au tomatic headlights switch on and
off depending on b rightness, fo r example in
tw ilight, during rain or in tunnels¢,& .
:oo: -Side marker lights
~D -Low beam headlights
Rear f og light (s)
Press the appropriate b utton c> fig. 55:
0$-Rear fog ligh t(s)
Clear vi sion 51
adaptive light*
When switched on, adap tive ligh t adapts to
curves in the road depend ing on the vehicle
speed and the steering ang le. This provides
better light ing through the curve. The system
operates at speeds between approximate ly
6 mph (10 km/h) and 68 mph (110 km/h).
Stati c corner ing light* (vehicles with adaptive
light) -the cornering light switches on at
speeds up to approximately 25 mph (40 km/
h) w hen a certain steering wheel angle is
reached o r when a turn signal is activated. The
area to the s ide of the vehicle is illuminated
bette r whe n turn ing .
The adaptive light and the cornering light only
functio n when the switch is in the AUTO posi­
t ion (automatic headlights*) .
A WARNING
-Daytime r unning lights and automa tic
headlights* are only intended to ass ist
the driver . T hey do n ot relieve the driver
of his responsibili ty to che ck the head ­
lights and to t urn them on manua lly ac ­
cording to the current light and visibility
conditions. For examp le, fog cannot be
detected by the light sensors*. So a lways
sw itch on the headlights
~D under these
weather conditions and when driving in
the dar k.
- Cras hes can happen when you cannot see
the road ahead and when yo u cannot be
see n by other motoris ts. Always tu rn on
the head lights so that you can see ahead
a nd so that ot hers can see your car from
t he b ack.
- P lease obey all laws when using the
lig hting sys tems descr ibed here.
(D Note
The rear fog lights shou ld only be turned
on in acco rdance with t raff ic regu lation, as
the lights a re bright for following traffic. ..,.

52 Clear vis ion
@ Tips
- The light sensor* for headlight control is
located in the rear view m irror mount.
You should therefore not apply any st ick­
ers to the windsh ield in this area in order
to prevent malfunctions or failures.
- Some exterior lighting functions can be
adjusted
¢page 52.
- When you remove your key from the igni­
tion while the vehicle's lights are turned
on, a buzzer sounds as long as the driv­
er's door is open .
- In cool or damp weather, the ins ide of
the headlights, turn signals and tail lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clea r shor tly after
switching them on. This does not affect
the service life of the lighting.
- In the even t of a light sensor malfunc­
tion, the driver is no tified in the instru­
ment cluster disp lay¢
page 22.
Turn signals and high beam lever
The lever operates the turn signals, the high
beams and the headlight flasher .
Fig. 56 Tu rn s ig na l and hig h beam lever
Turn sign als ¢i ¢
The turn signals activate when you move the
l ever into a turn s ignal pos ition when the ign i­
tion is switched on.
(D -right turn signal
@-left tur n signa l
The turn s ignal blinks three times if you just
tap the lever .
High be ams and headlight flasher [D
Move the lever to the correspon ding posit io n:
@ -high beams on
@ -high beams off or headlight flasher
The indicator light
ii in the instrument cl us­
te r turns on .
Notes on thes e features
-The turn signals on ly wor k w ith the ignition
t ur ned on. The indicator ligh ts
Ct or a in
the instrument cluster also blink.
- After you have turned a co rner, the turn s ig ­
na l switches off au toma tically .
- The
high beam works on ly w hen the head­
lights a re on. The ind icator ligh t
II in the
instrument cluster illuminates when the
high beams are on .
- The
headlight flasher works o nly as long as
you ho ld the lever -even if there a re no
lights switched on . The indicator light
II in
the instrument cluster illuminates when you
use the headlight flasher.
A WARNING
--
Do not use the h igh beam or headlight
flasher if you know that these could blind
oncom ing traffic.
Adjusting exterior lighting
The functions ore selected in the radio or
MMI" .
.,. Select: !CARI function button> Exte rior
light ing .
Or
.,. Select: !CARI function button > Car systems *
control button > Vehicle s etting s> Exterior
lighting .
Coming home (light when leav ing car }*,
Leav ing home (light when unlocking car )*
The coming home function illuminates the
area around the vehicle when the ignition is
switched off and th e dr ive r's door is open ed.
Depend ing on veh icle equ ipment, the function
can be switched on and off or the length of
time the lig hts remain on* can be ad justed . ..,.

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Cleaning the headlights*. The headlight wash­
er system* operates only when the headlights
are on. If you move the lever to position@,
the headlights a re washed in intervals .
_& WARNING
-The rain sensor is only intended to assist
the driver. The driver is still responsible
for manually switching the wipers on ac­ cording to the visibility conditions.
- The windshield may not be treated with
water-repelling windshield coating
agents. Unfavorable conditions, such as
wetness , darkness, low sun, can result in
increased glare. Wiper blade chatter is
also possible.
- Properly functioning windshield wiper
blades are required for a clear view and
safe driving ¢
page 57, Replacing
windshield wiper blades.
(D Note
- In the case of frost, check whether the
windshield wiper blades are frozen to
the windshield. Switching on the wind­
shield wipers can damage the wiper blades!
- Prior to using a car wash, the windshield
wiper system must be switched
off (lever
in position @). This helps to prevent un­
intentional switching on and damage to
the windshield wiper system .
- The windshield wipers are switched
off
when the ignition is turned off . Activate
the windshield wipers after the ignition is switched back on by moving the wind­
shield wiper lever to any position.
- Worn or dirty windshield wiper blades result in streaking . This can affect the
rain sensor* function . Check your wind­
shield wiper blades regularly.
- The washer fluid nozzles of the wind­
shield washer system are heated at low
temperatures when the ignition is on.
- When stopping temporarily, (e.g . at a
traffic light) the set speed of the wind-
Clear vision 5 7
shield wipers is automatically reduced by
one speed.
· Cleaning windshield wiper blades
Clean the windshield wiper blades when they
begin to leave streaks. Use a soft cloth and
glass cleaner to clean the windshield wiper blades.
.. Place the windshield wiper arms in the se rv­
ice position. Refer to¢
page 57.
.. Lift the wiper arm away from the front win­
dow.
_& WARNING
Dirty windshield wiper blades can impair
your view. This can lead to accidents.
Replacing windshield wiper blades
Fig. 65 Remov ing w in d sh iel d w iper blade
Wiper service position/blade replacement
position
.. Switch the ignition off and move the wind­
shield wiper lever to position©¢
page 56,
fig . 64.
The windshield wipers move into the
service position.
.. To bring the wipers back into the original
position, switch the ignition on and press
the windshield wiper lever.
You can also turn the service position on or
off
in the radio/MM!*:
.. Switch the windshield wipers
off (position
@ ¢page 56, fig. 64).
.. Select: !CAR ! function button > Windshield
wipers
> Service position > on/off . Or ..,_

64 Seats and storage
In addition to the driver 's seat settings, you
can also store and access the exterior mirror
ad justment settings* using the remote con­
trol key or memory button.
Remote control key
Applies to vehicles: with seat memory
To assign the driver's seat settings to the re­
mote contro l key when locking the vehicle, the
function must be activated in the radio or
MMI*
• Se lect :
I CAR I funct ion button> Seat adj ust ­
ment
> Dri ver's se at > Remote c ontrol k ey >
on .Or
• Se lect :
,..,I Cc-cAc-cRc-, 1 funct ion button > Car system s*
control button > Vehicle setting s > Seats >
Driv er' s s eat > Remot e cont rol key > On .
(D Tips
If you do not want another d river's set­
tings to be assigned to the remote key,
sw itch off the memory function us ing the
rad io or MMI* or the
!ON/OFF I button
c:::>page 64.
Memory buttons
App lies to vehicles: with seat memory
Fig. 73 Driver 's door: memory functio n buttons
The memo ry but tons are located in the dr iv­
e r's door .
Switching the memory function on /off
• Press the ION/O FF I button to switch the
memo ry fu nction on/off. The word
OFF
li ghts up when the memory funct io n is
swit ched off. Seat profi les are neither stored
nor recalled .
Storing a s eat p rofile
• Press the ISET I button. When the word SET
lights up, the memory is ready to store set ­
tings.
• Press a memory button
dII or [Ii) briefly . A
tone confirms that the settings were stored.
Acces sing a seat profile
• If the driver's door is open and the ignition
is switched off, press the memory button.
• If the driver's door is closed or the ignition is
switched on, press and ho ld the memory
button until the seat adjustment is com­
plete .
A WARNING
-For safety reasons ., the seat setting can
only be recalled when the vehicle is sta­
tionary -ot herwise you ris k having an ac­
cident.
- I n an emergency the recall proced ure can
be cancelled by p ressing the
ION/OFF I
sw itch or by tapping the memory bu t­
ton s.
Ashtray
Fig. 7 4 Center console : ashtray
Opening /cl osi ng
• To open the ashtray, slide the cover up
c:::> fig. 74.
• To close the ashtray, press down on the cov­
er.
Emptying the ashtray
• To remove the insert, s lide the latch to the
right
c:::> fig. 74 -arrow- . ..,_

70 Warm and cold
Operation
We recommend pressing the IAUTOI button and setting the temperature to 72 °F (22 °C) .
Fig. 83 Automat ic cl imate control system: control
Fig. 84 3-zo ne de luxe automatic cl imate contro l' : contro ls
Press the buttons to turn the funct ions on or
off. Use the d ials to adjust the temperature,
the blower speed and the a ir distribution . The
LED in a button will light up when the func­
tion is switched on. The settings are disp layed
for a few seconds in the radio or MMI* display.
In vehicles with a 3 -zone deluxe automat ic cl i­
mate control systems*, the dr iver and front
passenger side can be adjusted separately .
The settings are also displayed in the climate
control sys tem display.
IOFF I Switching the climate control
system on/off
The IOFFI button switches the climate control
sys tem on or off . It also switches on when you press the knob. Airflow from outside
is
blocked when the climate control system is
switched off .
IA/CI Switching cooling mode on/off
The air is not coo led and humidity is not re­
moved when cooling mode is switched off .
This can cause fog on the windows. Cooling
mode switches off automatically when the
outside temperature is below ze ro .
1- 1 Switching recirculation mode on/off
In recircu lation mode, the air inside the vehi­
cle is c irculated and filtered. This prevents the
unfiltered air outside the vehicle from enter­
ing the vehicle interior . We recommend