2015 AUDI RS5 CABRIOLET display

24 Driver information d isplay
Trip computer
Introduction
The trip computer gives you information on
current and average fuel mileage, average
speed, fuel range and driving time .
Fig. 9 Trip computer display: Average fuel mileage
The following information is continuously
eva luated by the trip computer and can be dis­
played sequentially in the instrument cluster
display:
Fuel range
The estimated cruising range in miles (km)
appears in the display. This tells you how far
your ve hicle wi ll be able to travel on the cur­
rent tank of fuel and with the same driving
style. The display changes in increments of
5 miles (10 km).
The cruising range is calcu lated based on the
fuel consumption for the last 18 miles
(30 km).
If you drive conservat ively, the cruis­
ing range will increa se.
Average fuel mileage The average fuel economy in MPG (l/100 km)
since you last cleared the memory appears in
this display. You can use this display to adjust
your driving technique to achieve a desired mileage.
Current fuel mileage
The instantaneous fuel consumption in mi les
per gallon (l/100 km) is shown in this display .
You can use this display to adjust your driving
technique to achieve a desired mileage. Fuel
consumption is recalcu lated at intervals
of 33 yards (30 meters). This disp lay switches
to gallons/hour (liters/hour) when the vehicle is not moving.
Average speed
T he average speed in mph (km/h) s ince you
last reset the memory appears in the display.
Elapsed time
The length of time that you have been driving
s ince you last reset the memory appears in
th is disp lay.
Distance
The distance that has been covered since the
last t ime the memory was cleared appears in
the display.
(0 Tips
- Fuel consumptions (average and cur­ rent), range and speed are displayed in
metric units on Canadian models.
- All stored values will be lost if the vehi­
cle battery is disconnected .
Memories
The trip computer is equipped with two fully
automatic memories.
Fig. 10 Tri p computer display: memory level 1
You can swi tch between the trip computer 1
and 2 by pressing the
I RESET I button @
r:!>poge 25, fig. 11.
You can te ll wh ich memory leve l is currently
active by the number or the sign in the display
¢fig. 10. The data from the single-trip mem­
ory (memory level 1) is being displayed if a
O .,.

M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
appears in the display. If a fJ is shown, then
the data from the total -trip memory is being
disp layed (memory leve l 2) .
Single-trip memory (Trip computer 1)
The single-t rip memory stores the trip infor ­
mat ion from the time the ignition is turned on
unti l it is turned
off. If the trip is continued
within 2 hours from the time the ignition was
turned
off, the new data will be included in
the calculation of the current trip informa­
tion . If the trip is interrupted for
more than 2
hours
the memory is reset automatically .
Total-trip memory (Trip computer 2)
Unlike the sing le-trip memory, the tota l-trip
memory is not reset automatically. Th is per­
mits you to evaluate your driving data for the
entire period between manual resets.
Operation
The trip computer is controlled by two
switches on the windshield wiper lever.
Fig. 11 Windsh ield w iper lever : contro ls fo r th e trip
co mpute r
Operating
• To disp lay the trip computer memory levels,
press the
I RESET I button @¢ fig. 11 re­
peatedly unti l the desired memory leve l is
shown in the d isplay.
• To d isplay trip information within a memory
level, press the top or bottom part of the
function selection switch @.
The trip computer will not operate unless the ignit ion is on. When you turn on the ignition,
the function that was in use when you last
turned the ign ition
off will be displayed .
Driver information display 25
In addition to information about the trip com­
puter (trip computer 1 and 2), information
about other systems can a lso be shown in the
display. To switch the display between the dif­
ferent information, tap the
I RESET I button @
briefly.
Resetting values to zero
• Select a value in the desired trip comp uter.
• Press and hold the
I RESET I button @for at
least one second. All values in the selected
trip computer are reset to zero.
With some vehicle equipment levels, the val ­
ues for the sing le trip or total trip memory
can a lso be reset in the Infotainment system
¢page 25.
(!) Tips
All stored va lues will be lost if the veh icle
battery is disconnected.
Basic Settings for the trip computer
The radio or MMI* operating unit is used for
setting the trip computer's basic settings.
• Select: Function button !CAR !> Instrument
cluster > On-board computer
1 or On-board
computer
2.
The values in the sing le-trip or the total-trip
memory can all be reset to zero at the same
time under
Reset in the menu.
In addition, yo u can determine what informa ­
tion from the trip computer should be shown
in the instrument cluster display. If one of the
pieces of driver information is turned
Off , that
driver information will not be shown in the
display. The information w ill continue to be
calculated by the tr ip computer and can be
turned back
On at any time.
(j) Tips
This function is not available on all
vehicles.

26 Driver information d isplay
Service interval display
The service interval display reminds you when
your next service is due.
Fig. 12 Display : Service interva l display
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed
accordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
turn on the ignition
r::;; fig. 12.
After about 5 seconds the display switches
back to normal. The d istance and time re­
maining are updated each time the ignition is
turned on until the date due for service is
reached .
Service due
When the due date for service is reached, the
message
Service due! appears in the instru ­
ment cluster immediately after you turn on
the ignition. Additionally, a warn ing tone
sounds . After about 5 seconds the display
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the radio or MMI* display by
selecting the serv ice interval display in the car
menu. SelectlCARlfunction button>
Service
interval display
or I CARI function button > Car
systems*
control button > Servicing &
checks. Resetting the
service interval display
Your authorized Audi dea ler will reset the cor­
responding service schedule after performing
the appropriate service on your vehicle. You
also have the possibil ity to reset the oil
change schedule after having performed an
oil change according to Audi specifications.
Select I CAR ! function button >
Service interval
display
> Reset oil change interval or I CAR I
function button
> Car systems* control but­
ton >
Servicing & checks > Reset oil change
interva l.
(D Note
-Only reset the oil change display when
you have comp leted an oil change.
- If you disconnect the battery terminals,
no ca lculations can be made for the serv­
ice interval display dur ing this time and
no serv ice reminder will appear. Remem­
ber that observing the proper service in­
tervals is vita lly important to extending
the life of your vehicle, particularly the
engine, and maintaining its value. Even if
the mileage driven is low, the maximum
period of one year from one service to
the next must not be exceeded.
{D Tips
The information in the Service Reminder
remains stored even when the vehicle bat­
tery is d isconnected .
Engine oil temperature
indicator
Fig. 13 Display : engine o il temperature indicato r

"' N
a: LL co
rl I.O
"' rl
"' rl
.. With the ignition switched on, press the
I RESE T I button <=> page 25, fig. 11 repeated­
ly until the engine o il temperature indicator
is shown.
If the engine o il temperature is be low 140 ° F
(60
°(), the 1!11 symbol followed by three hy­
phens"- --" and the
0
( unit is shown.
At an engine o il temperature above 140 °F
(60 °C) the engine has reached its operating
temperature. The engine oil temperature may be higher if there is heavy engine load and
high temperatures outside. This is not a cause
for concern as long as the.<=>
page 17 or
the
Bl <=> page 17 warning light in the display
does not flash .
Lap timer
Introduction
You can record and eva luate lap times with
the lap timer in the display<=>
page 27,
fig . 15 . The time is measured in minutes, sec­
onds and 1/10 seconds . The hours are also
shown when the lap time exceeds 60 minutes .
The maximum ind ividual measurement is 99
hou rs. A max imum of 99 laps may be reco rd ­
ed.
_& WARNING
-
Please devote your fu ll attent ion to driv­
ing . As the driver, you have comp lete re ­
sponsibility for safety i n traffic. Only use
the functions in such a way that you always ma intain complete control over your veh i­
cle in all traff ic situations .
@ Tips
When the lap timer stopwatch is running,
you can call up the trip computer informa­
tion with the
I RESE TI button. Dri
ver inform ation di spl ay 2 7
Calling up the lap timer and timing
Fig. 14 Contro ls
F ig . 1 S Display: Lap t imer
Calling up the lap t imer
.. Press the I RESET ! button<=> fig. 14@ until
the lap timer <=>
fig. 15 appears .
Timing laps
.. To sta rt timing, press the upper section of
t he wiper swi tch@ . The time measurement
is shown in line@<=>
fig. 15.
.. To stop t iming, press the upper section of
the wiper switch ® again . This also starts
timing the next round. The prev ious t iming
always moves one line down, first into line
@ , and then into lines @ and @. The lap
number that corresponds to the tim ing is
disp layed in front of the ind iv idual timings.
Di splaying inte rmediat e time and pau sing
timing
.. To display an intermed iate time, press the
lower section of the wiper switch @. The
tim ing continues to run i n the background .
.. To pause t iming, press the lower section of
the wiper swi tch @ agai n.
.. To continue tim ing, p ress the uppe r section
of the wiper switch @.
Ill>

28 Driver information d isplay
If timing is paused, you can continue it late r
even if you sw itch the ignition off .
Evaluating times and continuing or
resetting timing
You can evaluate the fastest, slowest and
average lap times.
Fig. 16 Dis play : lap time eva luat ion
.,. To evaluate lap times, press and hold the
I RESET I button ¢ page 27, fig. 14 @for ap­
proximate ly
2 seconds. The number of laps
t raveled, the fastest lap"+", the slowest lap
" -" and the average lap time "0" appears in
the display .
.,. To continue timing for additional laps, press
the wiper switch @ .
.,. To reset the timer to zero, press and hold
the
I RESET I button again for approximately
2 seconds .
.,. To switch the lap timer off comp letely, press
the
I RESET I button br iefly.
@ Tips
- Saved lap times cannot be ind ividually
deleted from the total results.
- The saved lap timer values will not be
l ost after turning the ignition off .
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL )
The Malfunction Indicator Lamp (MIL) ¢"4 in
the instrument cluster is part of the On-Board
Diagnostic (OBD II) system. T
he warning/indicator light illuminates when
the ignition is switched on and goes out after
the engine starts and the id le has stabilized .
This indicates that the MIL is working proper­
ly.
If the light does not go out after the engine
is started, or illum inates while you are dr iv­
ing, a malfunction may exist in the engine sys­
tem . If the light illuminates, the catalytic con­
verter could be damaged .
Cont inue driving
with reduced power (avoid­
ing sustained high speeds and/or rapid accel­
erations) and have the condition corrected.
Contact your authorized Audi dea ler .
An improperly closed fuel filler cap may also
cause the
MIL light to illuminate
¢ page 192 .
On-Board Diagnostics
Fig. 17 Locat io n of Data Link Co nnector (O LC)
On-Board Diagnostics monitors the compo­
nents of your emission contro l system. Each
monitored component in your engine system
has been assigned a code. In case of a mal­
function, the component will be identified
and the fault stored as a code in the control
module memo ry.
The MIL light may also illuminate if there is a leak in the on-board fuel vapor recovery sys­
tem .
If the light illuminates after a refueling,
stop the vehicle and make sure the fuel filler
cap is properly closed
¢ page 192.
In order to make an accurate diagnosis, the
stored data can on ly be displayed using spe­
cial diagnostic equipment (generic scan tool
for 080) .
ll>-

40 Opening and clo sing
-I «:s I button on the master key
- Handle in the rear lid
When the valet parking feature is activated,
the message
V ale t park ing activat ed appea rs
in the ins trument cluster display when you
switc h the ignition on.
Garage door opener
(Homelink)
Description
App lies to vehicles: with garage door opener ( Homelink)
Fig. 33 Garage door ope ner: exa mples of u sing wit h
diff erent sy stems
You can activate various systems such as ga ­
rage doors, sec urity systems and home light­
ing from inside yo ur vehicle using the ga rage
door opener (Homelink). There are three but­
tons for this in the vehicle headliner that can
be in used in place of up to three hand -he ld
transmitters.
To operate systems using the garage door
opener , the three buttons in the roof headlin­
er must be programmed first .
A WARNING
Make sure no people or objects are in the
immediate vicinity of the equipment when
using or programm ing the garage doo r
opene r. People can be injured and objects
can be damaged if they are caught in the
equipment .
@ Tips
-Fo r security reasons, we recommend that
you clear the programmed buttons be­
fore se lling the vehicle. -
For add itiona l information about Home­
Link, visit www.homelink .com.
- For Declara tion of Compliance to United
States FCC and Ind ustry Canada reg ula ­
tions
c::> page 267.
' . Operation
Applies to vehicles: with garage door opener (Homelink)
Fig. 3 4 Headli ner: con tro l uni t
Requir ement: The buttons in the roof head lin­
er must be programmed
c::> page 40 or
c::> page 41 and the ve hicle must be within
range of the system, such as the garage door
opener.
.,. Press the b utton to open t he garage door.
The LED @ blinks o r turns on .
.,. Press the button aga in to close the garage
door.
(D Tip s
To open or close the garage door, press the
button, but do not hold it for longer than
10 seconds or the garage door opener
module will switch to programming mode.
Programming the buttons (version A)
Applies to vehicles: with garage door opener (Homelink)
You can program both fixed code and rol ling
code systems using this procedu re .
Pro gramming or repr ogramm ing buttons
.,. Switch the ignition on .
.,. Press and hold the button in the roof head­
liner
c::> page 40, fig . 34 that you wou ld like
to prog ram for at least 10 seconds. Or
.,. Select:
!CARI function button> Car sy ste m s*
contro l butto n > Vehicle setting s > Garage IJJI,

"' N
a: LL co
rl I.O
"' rl
"' rl
door opener> Program garage door open­
er.
If this path is not available, program the
button as described in version
Bqpage41 .
.,. Follow the instructions in the MMI.
Erasing button programming
The programmed buttons cannot be erased
individually. They must all be erased together.
Reprogram the buttons if necessary .
.,. Select:
ICARI function button> Car systems*
control button > Vehicle settings > Garage
door opener> Clear program settings
>
Yes .
Displaying the version/status/country
code
.,. Select: I CARI function button > Car systems*
control button > Vehicle settings > Garage
door opener > Version information.
@ Tips
-Programming through the MMI* is not
possible with all infotainment systems.
If this is the case, program the buttons
as described in version B
c:> page 41.
- The required distance between the hand
transmitter and the HomeLink module in
the radiator grille
c:> page 41; fig. 35
depends on the system that you are pro­
gram ming.
- Depending on the model of the system,
you may need to release the button on
the remote control during programming
and press it again. Hold each position
you try for at least 15 seconds before
trying another position. Keep the turn
signals on your vehicle in view when do­
ing this.
- After programming the garage door
opener, it may be necessary to synchron­i ze the motor with the system. Refer to
the manufacturer's instructions.
Opening and closing 41
Programming the buttons (version 8)
Applies to vehicles: with garage door opener (Homelink)
Fig. 35 Distance be tween the ra diato r grille and the
hand transmitter
Programming the button: Part 1 with the
controls
1. Switch the ignition on.
2. Press and hold both outer buttons in the
roof headliner
c:> page 40, fig. 34 until the
LED @turns off completely (after about
20 seconds). This procedure clears the
standard codes that were set at the facto ­
ry and does
not need to be repeated again
to program the other buttons.
3. Briefly press the button on the roof head­
liner that you would like to program.
4. Wait until the LED @ begins to blink
quickly. Programming mode is active for 5
minutes.
5. Move in front of your vehicle while hold­
ing the original remote control for the
system that would like to program to a
button in the roof headliner.
Programming the button: Part 2 at the
radiator grille
6. Hold the remote control up to the radiator
grille on your vehicle
c:> fig. 35.
7. Press and hold the remote control until
the turn signals on your vehicle blink. This
may take up to 30 seconds.
8. If the emergency flashers blink three
times, the programming was successful.
If the emergency flashers only blink one
time, the 5 minute time limit for the pro­
gramming has ended or the programming
was not successful. Repeat the program­
ming from the third step, or try changing
t he distance to the radiator grille. .,.

44 Power top
-When operating the power top, visibility
to the rear is limited . Avoid operating the
top while driving in reverse.
(D Note
- To prevent damage to the power top:
- do not store any objects in the power
top compartment.
- make sure there is enough space above
the vehicle when opening or closing
the power top.
- To reduce the risk of damage, make sure
there are no fragile objects within the
storage bay's range of motion.
@ Tips
-To prevent the battery from draining, do
not open or close the power top repeat­
edly when the engine is switched off.
- A message will appear in the instrument
cluster display if there is a power top
malfunction
~ page 45.
- The power top can also be operated
manually if there is a malfunction
¢ page 47, Power top emergency op­
eration.
The cause of the malfunction
should be corrected by an authorized
Audi dealer or authorized repair facility
as soon as possible.
- The vehicle is not protected from the
weather or from unauthorized entry if
the vehicle is left parked with the power
top open. Lock any objects you are leav­ ing in the vehicle in the luggage com­
partment. Close the power top before
leaving the vehicle.
- The side windows lower slightly auto­
matically when opening/closing the pow­
er top .
Power top convenience opening/closing
Fig. 37 Remote control key: buttons
Fig. 38 Turning the key to open and close
Convenience opening with the driver's
door lock
.. Press them button on the remote control
key to unlock the vehicle.
N
~ co aJ
.. Turn the key once in the driver 's door lock to
the opening position @¢
fig. 38 .
.. Turn the key to the opening position again
within two seconds and hold it there until
the power top opens completely.
Convenience closing with the driver's door
lock
.. Turn the key once in the driver's door lock to
the closing position@¢
fig. 38.
.. Turn the key to the closing position again
within two seconds and hold it there until
the power top closes completely.
Releasing the key stops the opening or closing
process
immediately .
A WARNING
-Read and follow the important safety pre­
cautions ¢
A in Opening/closing the pow­
er top on page 43.