110 Park assist
Parallel Parking
Applies to vehicles: with par king system p lus w it h rear
view ca mera
Use parking mode 2 to help you park on the
edge of a street.
F ig. 129 MMI Display: blue s urface in the parking spot
Fig. 130 MMI Disp lay: Blue curve on the curb
The following steps apply only when there is
no obstacle (such as a wall) near the parking
spot. Otherwise, please read the "Tips on Parking Next to Obstacles"¢
page 110.
.. Activate the turn signal.
.. Position your vehicle parallel to the edge of
the street, approximately 3 ft (1 m) from a parked vehicle .
.. Switch the MMI on and select the reverse
gear. The parking aid turns on and parking
mode 1 appears on the display.
"Press the
Mode¢ fig. 129 © control button
on the MMI control console. Parking mode 2
appears .
.. Back up in reverse gear and align your vehi
cle so that the blue area
@ borders on the
rear end of the vehicle or on the parking
spot line. The blue area represents an exten
sion of the vehicle's outline by approximate ly 16 ft (S m) to the rear. The long s ide of the blue
area shou ld be on the curb. The en
tire blue area must fit into the parking spot.
.. While the vehicle is stationary, turn the
steering wheel to the rig ht as far as it will
go.
" Back into the parking spot. Stop the vehicle
as soon as the blue curve is nea r the curb
q fig . 130 ¢0.
"Whil e the vehicle is stationary, turn the
steering wheel to the left as far as it will go .
.. Continue to back up into the parking spot
until the vehicle is parked parallel to the
curb .@ marks the rear bumper. You should
stop driving in reverse as soon as and no lat
er than when the red orientation line@
abuts an object¢_&. ! Keep an eye on the
front of your vehicle while do ing th is ¢ 6) .
Parking next to obstacles
When there is an obstacle (such as a wa ll)
next to the parking spot, choose a spot with
more space on the sides. Posit ion the long
s ide of the blue area so that there is suff ic ient
space from the curb . The area must not be on
the curb . You will a lso need to start turning
the steer ing wheel much earlier. There should
be a sufficient amount of space between the
curb and the blue curve, and the blue curve
¢
fig. 130 must not touch the curb.
A WARNING
- The rear view camera does not show the
entire area behind the vehicle
¢
page 10 7, fig. 12 5. Watch out espe
cially for small children and anima ls. The
rear view camera cannot always detect
them, posing risk of an acc ident!
- Please note that objects not touching the
ground can appear to be further away
than they really are (for example, the
bumper of a parked vehicle, a trailer
hitch, or the rear of a truck). In this case,
you should not use the help lines to help
with parking, which poses danger of an
accident!
.__ _____________ _J ...
M N
er
u..
co ,...., \!) ..,.,
,...., ..,., ,....,
(D Note
-In the MMI display, the directio n of trav
el of the vehicle rear is represented de
pending on the steering wheel angle.
The vehicle front swings out more than
the veh icle rear . Maintain plenty of dis
tance from an obstacle so that your out
s ide mirro r or a corner of your veh icle
does not collide with any obstacles -dan
ger o f accident!
- Remember to ma inta in sufficie nt clear
ance from the curb to avoid damaging
the wheel rims.
(j) Tips
The left or right orientation lines and sur
faces will be di splayed, depend ing on the
t ur n signa l being use d.
Adjusting the display
and warning tones
Applies to vehicles: with parking system plus/ parking sys
tem plus with rear view camera
The display* and warning tones are adjusted
in the radio or MMI*.
,.. Se lect : I CARI fu nct ion button > Parking sy s
tem.
Or
,.. Se lect : ~ I C~ A,..., R,..., I function button > Car system s*
control button > Drive r assist > Parking aid .
Display*
-Off -when t he parking system is sw itch ed
on, only a udib le signa ls are given .
-On -when the parking sys tem is switched
on, the pict ure from the rear view camera is
displayed.
Warning tones
- Rear volume -
rear sensor volume
-Rear frequency -rear sensor frequency
-Front volume -front sensor volume
-Front frequency -front sensor freq uency
- Mu sic volume while pa rking -when the
parking system is switched on, the vol ume
of the activ e audio source is lowered.
P ark a ssis t 11 1
The newly adj usted va lue is briefly hea rd from
the sig na l generato r. Th e settings are auto
matically stored and assigned to the remote
control key.
A WARNING
- Always make sure that the vo lume and
frequency of the warning tones is ad just
ed so that yo u can easily hear the acous
tic d istance signa l even if the radio is
p laying, the air-cond itio ne r blower is on
High or there is a high level of ou ts ide
noise.
- Chec k the settings whenever someone
e lse has drive n the vehicle before yo u.
(D Tips
- The warn ing tones can also be adjus ted
directly from t he rear view came ra im
age. S imp ly press the Sett ings* cont ro l
bu tton.
- Cha nged settings are ac tiva ted whe n
park ing ass ist is swi tc hed on aga in.
Error messages
Applies to vehicles: with parking system plus with rear
view camera
There is an error in the system if the LED on
the
p, ,; A switch is blinki ng and you hear a con
tinuous alarm fo r a few seconds after switch
ing on the park ing system or when the park
ing system is already activated . Have yo ur au
t h orized Aud i dea le r cor re ct the e rror.
Keep th e senso rs in the rea r bumpe r clean and
free from ice so that the acoust ic par k assist
system can fu nction properly.
@ Tips
If the error is not corrected before you
switc h off the ig nitio n, when you sw itch on
the p arking system again, the LED in the
P" JA switch will b link.
134 Airbag sys te m
For this reason, a nd because t he bac k seat is
the safest place for children - when prop erly
restra ined according to their age and size - we
strongly recommend that children always sit in the back seat
Q page 152, Child Safety.
A WARNING
-
A c hild in a rearward-facing child safety
seat installed on the front passenger seat
w ill be seriously injured and can be k illed if
t he front a irbag inflates - even wit h an Ad
v a nced Airb ag System.
- T he inflating a irbag will hit the child
safety seat or infant carrier with g reat
force and w ill smash the ch ild safety sea t
and child against the backrest, center
armrest, door or roof .
- Always install rear-facing child safety
seats on the rear seat .
-If you mus t inst all a rearwar d fa cing
child safety seat on the front passenger
seat because of exceptional circ umstan
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on , im
med iately install the rear-facing child
safety seat in a rear seating position and
have the a irbag system inspected by you r
au thorized Audi dealer .
- Forward-fac ing ch ild safety seats instal
led on the front passenger's seat may in
terfer e wi th the deployment of the air
bag and cause se rious personal injury to
the ch ild.
A WARNING
If, in exceptional c ircumstances, you mus t
install a forwa rd-facing child restra int on
the front passenger's seat:
- Always m ake su re the forw ard-fa cing
sea t has been des igned and certified by
its manufact urer for use on a front seat
with a passenger front and side airbag.
- Never put the forward -facing child re
st raint up aga inst or very near the inst ru
ment pane l.
- Always move the passenger seat into its
rearmost position in the seat's fore and aft ad
justment range, as fa r away from
the airbag as possible before installing
the forward-fac ing ch ild restra int. The
backrest must be ad justed to an upright
position .
- Make sure that the
PASSENGER AIR BAG
OFF
li ght comes on and stays on all the
time wheneve r the ignit ion is switched
on.
A WARNING
To reduce the risk of serious inju ry, ma ke
sure that the
PASSENGER AIR BAG OFF
lig ht w ill be displayed whenever a child re
straint is insta lled on the front passenger
seat and the ignition is switched on .
- If the
PASSENGER AIR BAG OFF light
does not stay on, per form the checks de
scribed ¢
page 141, Monitoring the Ad
vanced Airbag System.
- Take the chi ld restraint off the front pas
senger seat and install it properly at one
of the rear seat positions if the
PASSEN
GER AIR BAG OFF light does not stay on.
-Have the airbag system inspected by
your author ized Audi dealer immed iate
ly.
- Always carefully follow instr uctions from
child restraint manufacture rs when in
stalling ch ild restra ints.
A WARNING
-If, in except iona l circumstances, you must
i nstall a forward or rearwa rd -facing child
r estra int on t he front passenger's seat :
- Improper installation of ch ild restra ints
can reduce their effectiveness o r even
p revent them from providing any protec
tion.
- An improperly installed ch il d restra int
can inter fere with the airbag as it de
p loys and seriously injure o r even kill the
child -even with an Advance d Airbag
System.
- Always caref ully follow the m anu factur
er 's ins truc tio ns p rov ided with the ch ild
safety sea t or carrier .
178 Intelligent technology
operate, such as the inter ior lights or the
power seat adjustment. The convenience
functions will be ava ilable again when you
switch on the ignit ion and start the engine.
With th e engine turn ed off
If yo u listen to the radio, for example, with
the engine turned off or use other MMI fu nc
tions, the battery is being discharged .
I f sta rting capabi lity is jeopa rdized due to en
e rgy consumpt ion, the fo llowing warning ap
pears in the MMI display:
Please start the eng ine soon or th e syste m
will be turned off .
The warning ind icates that the system will be
turned off automatically after 3 m inutes. If
you wish to con tinue us ing t he functions, you
have to s tart the engi ne.
With the engine running
A lthough electrical energy is generated when
the veh icle is be ing dr iven, the battery can be
come discharged . T his happens most ly when
little energy is be ing generated a nd a great
deal consumed and the battery 's state o f
charge is no t optima l.
To br ing the energy balance back into equili
b rium, consumers which require especially
l arge amo unts of energy are tempo rari ly cut
back or switched off. Heating sys tems in par
ticular require a great dea l of energy . If you
notice, for example, that the heated seats* or
the heated rear window are not heating, they have been temporar ily cut back or switched
off. These systems will be ava ilable again as
soon as the energy ba lance has been restored.
You will a lso notice that engine idle speed has
been increased slightly. This is norma l and not
a cause for concern . By increasing engine idle
speed the add itiona l energy required is gener
ated and the batte ry is charged .
188 Vehicle care and cleaning
- Never clean headlights or tail lights
with a dry cloth or sponge.
- Do not use any cleaning product that
contains alcohol, because they could
cause cracks to form.
-Wheels
- Never use any paint polish or other
abrasive materials.
- Damage to the protective layer on the
rims such as stone chips or scratches
must be repaired immediately .
-Sensors/camera lenses
- Never use warm or hot water to re-
move snow or ice from the camera
lens. This could cause the lens to crack.
- Never use abrasive cleaning materials
or alcohol to clean the camera lens.
This could cause scratches and cracks.
- Power top
- Remove bird droppings immediately.
- Never use gasoline, stain remover, ben-
zene, paint thinner or other solvents to
remove stains.
- Windows
- Remove snow and ice on windows and
exterior mirrors with a plastic scraper.
To avoid scratches, move the scraper
only in one direction and not back and
forth.
- Never remove snow or ice from win
dows and mirrors using warm or hot
water because this could cause cracks
to form.
- To avoid damage to the rear window
defogger, do not apply any stickers on
the heating wires on the inside of the
window.
- Decorative parts/trim
- Never use chrome care or cleaning
products.
-Paint
- To reduce the risk of scratches, the ve-
hicle must be free of dirt and dust be
fore polishing or waxing.
- To prevent paint damage, do not polish
or wax the vehicle in direct sunlight. - To reduce the risk of paint damage, do
not polish away rust film.
- Remove cosmetics and sunblock imme
diately. Otherwise, the paint could be
damaged.
- Displays
-To avoid scratches, do not use dry
cleaning methods on displays .
-Controls
- Make sure that no fluids enter the con-
trols, because this could cause dam
age.
- Safety belts
- Do not remove the safety belts to clean
them.
- Never clean safety belts or their com
ponents chemically or with corrosive
fluids or solvents and never allow sharp objects to come into contact
with the safety belts . This could cause
damage to the belt webbing.
- If there is damage to the webbing, the
connections, the retractors or the buck
les, have them replaced by an author
ized Audi dealer or qualified workshop.
-Textiles/Vinyl/ Alcantara
- Never treat Vinyl/Alcantara with leath-
er care products, solvents, floor polish,
shoe polish, stain remover or similar products.
- To avoid damage, have stubborn stains
removed by an authorized Audi dealer
or qualified workshop.
- Never use steam cleaners, brushes,
hard sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry
the seat.
- Objects with sharp edges such as zip pers, rivets on clothing or belts can
cause damage to the surface.
- Open hook and loop fasteners, for ex ample on clothing, can damage seat
covers. Make sure hook and loop fas
teners are closed .
-Natural leather
198 Checking and filling
Using the proper engine oil is important for
the functionality and service life of the en
gine. Your engine was factory-filled with a
high-quality oil which can usually be used
throughout the entire year.
0 Note
Your Limited New Vehicle Warranty does
not cover damage or malfunctions due to
failure to follow recommended mainte
nance and use requirements as set forth in
the Audi Owner's Manual and Warranty
&
Maintenance booklet.
- Use only a high quality engine oil that ex
pressly complies with the Audi oil quality
standard specified for your vehicle's en
gine . Using any other oil can cause seri
ous engine damage.
- Do not mix any lubricants or other addi
tives into the engine oil. Doing so can
cause engine damage.
If you need to add oil and there is none
available that meets the Audi oil quality
standard your engine requires, you may
add a total of no more than 0.5 quart/liter
of a high-quality "synthetic"oil that meets
the following specifications.
- Vehicles with gasoline engine: ACEA A3
or API SM with a viscosity grade of
SAE 0W-30, SAE SW-30 or SAE SW-40.
- For more information about engine oil
that has been approved for your vehicle, please contact either your authorized
Audi dealer or Audi Customer Relations
at 1 (800) 822-2834 or visit our web site
at www.audiusa .com or
www .audicanada .ca .
Engine oil consumption
The engine in your vehicle depends on an ade
quate amount of oil to lubricate and cool all
of its moving parts.
In order to provide effective lubrication and
cooling of internal engine components, all in
ternal combustion engines consume a certain amount of oil. Oil consumption varies from
engine to engine and may change significantly
over the life of the engine. Typically, engines
with a specified break-in period (see
¢ page 179) consume more oil during the
break -in period than they consume after oil
consumption has stabilized.
Under normal conditions, the rate of oil con
sumption depends on the quality and viscosity
of the oil, the RPM (revolutions per minute) at
which the engine is operated, the ambient
temperature and road conditions . Further fac
tors are the amount of oil dilution from water
condensation or fuel residue and the oxida
tion level of the oil. As any engine is subject to
wear as mileage builds up, the oil consump
tion may increase over time until replacement of worn components may become necessary.
With all these variables coming into play, no
standard rate of oil consumption can be es
tablished or specified. There is no alternative
to regular and frequent checking of the oil lev el, see
Note.
If
the yellow engine oil level warning symbol
El in the instrument cluster lights up, you
should check the oil level as soon as possible
¢ page 199. Top off the oil at your earliest
convenience
¢ page 199.
A WARNING
--
Before you check anything in the engine
compartment, always read and heed all
WARNINGS¢
& in Working in the engine
compartment on page 195.
{(D Note
Driving with an insufficient oil level is like
ly to cause severe damage to the engine .
(D Tips
- The oil pressure warning display. is
not an indicator of the oil level. Do not
rely on it. Instead, check the oil level in
your engine at regular intervals, pref erably each time you refuel, and always
before going on a long trip. .,.
"' N
a: LL co
rl I.O
"' rl
"' rl
-If you have the impression your engine
consumes excessive amounts of oi l, we
recommend that you consult an author
ized Audi dealer to have the cause of
your concern properly diagnosed. Keep in mind that the accurate measurement of
oil consumption requires great care and may take some time. An authorized Audi
dealer has ins tructions about how to
measure oil consumpt ion accura tely.
Checking the engine oil level
F ig. 175 MMI Display: Oil leve l indicator
Read oil le vel
"' Park your vehicle so that it is horizonta lly
level.
"' Shut the engine off when it is at operating
temperature.
"' Switch only the ignition back on .
"' Wa it approx. two minutes.
"' Se lect: Funct ion button
I _C_A_R_I > Oil l e v e l. Or
"' Se lect: Funct ion button
I CARI > Car sy s-
tem s* control button > Servicing & check s >
Oil level.
"' Read the oil leve l in the MMI* Display
r:::> fig. 175. Add engine oi l if the bar of the
o il level indicator is near "min"
r:::> page 199
Depending on the way the vehicle is driven
and the operating conditions, oil consumption
can be up to 1 quart per 600 mi les (0.8 liter
per 1,000 km). Consumption may be higher
within the first 3,000 miles (5,000 km) .
(D Tips
The oil level indicator in the MMI* Disp lay
is only an information display . If the oil
level is too low, a min imum oil warning ap-
Checkin g and fillin g 199
pears in the instrument cl uster . Add oil
Q page 199. If the hood has been opened,
the current oil leve l is shown in the instr u
ment cluster the next time the ignition is
switc hed on.
n eck
"' Before you check anything in the engine
compa rtment,
alwa ys read and h eed all
WARNINGS r::> .&. in Working in the engine
compartment on page 195.
"' Shu t the eng ine off.
"' Unscrew the cap
't::::r. to the engine oil filling
hole
¢ fig. 176, ¢page 197, fig. 174.
"'Carefully top off with 0 .5 quarts (0 .5 liters)
of the appropr iate oil
¢page 197.
"'Check the oil level again after two minutes
r:::> page 199, Checking the engine oil level.
"'Top off the o il aga in, if necessary .
"' Screw the cap back on the fi lling hole .
.&_ WARNING
-W hile topping off, the o il m ust n ot come
in contact with hot e ngine parts -fir e
hazard !
- Th e oi l filler cap mus t be p roperly se
cured to prevent oil from being sp rayed
on the hot engine and exhaus t system
when the engine is runn ing -fire haza rd!
- If you r skin has come in contact wi th the
e ngine o il, you must subse quently
cleanse it thorough ly.
(D Note
- Check the oil leve l using the r adio or
M MI*. I f the message
Plea se reduce oil
24 0 T ire s and wheel s
According ly, when the low tire pressure te ll
tale illuminates, you shou ld stop and check
your tires as soon as possible, and inf late
them to the proper pressure. Driving on a s ig
n ificantly under-inflated tire causes the tire to
overheat and can lead to tire failure. Under-in
flation also reduces fuel efficiency and tire
tread life, and may affect the vehicle's han
dli ng and stopp ing ability.
Please note that the TPMS is not a subst itute
for proper tire maintenance, and it is the driv
e r's responsib ility to ma inta in correct tire
p ressu re, even if under- inflation has not
reached the leve l to trigger ill umination of the
TPMS low tire pressure telltale.
Your veh icle has also been equ ipped with a
TPMS malfunction indicato r to indica te when
the system is not opera ting properly. The
TPMS mal function indicator is combined wi th
the low tire press ure telltale . When the sys
tem detects a malfunction, the te lltale will
f lash fo r approximately one minute and then
remain cont inuous ly illuminated. This se
quence will continue upon subsequen t vehicle
start -ups as long as the ma lfunction ex ists .
When the malfunct ion indicator is ill uminat
ed, the system may not be able to detect or
signal low t ire pressure as intended . TPMS
malfunctions may occur for a variety of rea
sons , includ ing the installat ion of replace
ment or a lternate tires or whee ls on the veh i
cle that prevent the TPMS from funct ioning
p roperly. Always check the TPM S malf unct ion
tellta le after replacing one o r more t ires or
wheels on your veh icle to ensure that the re
p lacement or a lternate tires and wheels allow
the TPMS to continue to function p roperly. Tire pressure indicator appears
Applies to vehicles: wit h tire press ure mo nitor ing system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction .
Fig . 1 87 Displa y: un derin flation w arnin g
U sing the ABS sensors, the tire pressure moni
toring system compares the tire tread circum
ference and vib ration characteristics of the in
dividua l tires.
If the pressure decreases in one
or more t ires, this is indicated in the instru
ment cluster with a
RI] war ning symbol and a
message ¢
fig. 187 . The driver message in the
display goes out afte r 5 seconds . The driver
message can b e displayed again by pressing
t h e
ISE TI button. If o nly one t ire is affec ted,
the d isp lay w ill indicate its posi tion.
The tire pressure monitoring system must be reset via rad io or M MI* each time the pres
su res a re adjusted (e.g. when swit ching be
tween partial and f ull load p ress ure) or after
changing or rep lacing a tire on your ve hicle
¢
page 241 . The TPMS indicator only mon i
tors the ti re pressure that yo u have previous ly
stored. You can find the recommended tire
pressures for your vehicle on the label on driv
er 's side 8-pillar ¢
page 217.
Tire tread circumference and vibration charac
teristics can change and cause a ti re pressure
warning if:
- the tire press ure in one or more tires is too
low,
- the t ire has struc tural damage,
- t he t ire p ress ure was c hanged, wheels rota t-
ed or rep laced but the TPMS was not reset
¢ page 241. ..,_