2015 AUDI R8 SPYDER ESP

Intelligent technology
Press the I!! button briefly¢ fig. 126 . The II in­
dicator light turns on and Sport control Warn­
ing! Restricted st abilit y appears in the driver in­
formation system d isplay. Driving stability is lim­
ited in sport mode.
Sw itch ing ESC off
Press and hold the
l!I button for three seconds .
The ESC indicator light
fl turns on and Stabil i­
z atio n prog ram off appears in the display. ASR is
also switched off when ESC is sw itched off.
Sw itch ing on
Press the
l!J button again. The message Stabili­
zation progr am on appears briefly in the disp lay .
_& WARNING
You should only sw itch the ESC off if your dr iv­
ing ability and the traffic s ituation allow. This
could increase the risk of slipp ing.
- The stabilizing function is limited in ESC
sport mode. The driving wheels could spin and the vehicle could swerve, especially on
slick or slippery road surfaces.
- There is no vehicle stabilization when ESC is
switched off.
(D Tips
If there is a malfunction in the retractable
rear spo iler* or the A udi magnetic ride*, it
may not be possible to activate ESC sport
mode or normal mode may act ivate aga in au­
tomatically.
Braking
What affects braking efficiency?
New brake pad s
During the f irst 250 miles (400 km), new brake
pads do not possess the ir full braking effect, they
have to be "broken in" first¢.&. . The break- in pe­
riod can be considerab ly longer for vehicles w ith
ceramic b rake roto rs*. You can compensate for
this s light ly reduced b ra ki ng power by push ing
ha rder on the b rake peda l. Avoid heavy braking
loads during the bre ak-in period.
136
Operating conditions and driving habits
The bra kes on today's automobiles a re s till sub­
j ect to wear, depend ing largely on operating con ­
ditions and driving habits ¢& . On vehicles that
a re either driven most ly in stop-and-go city traf­
fic or are driven hard, the brake pads should be
checked by your authorized Aud i dealer more of­
te n tha n specified in the Warranty
& Maint e­
nance bookl et. Failure to have you r brake pads
i nspected can resu lt in reduced b rake pe rform­
ance.
On steep slopes, you shou ld use the braking ef­
fect of the engine . This way, you prevent un nec­
essary wear on the brake system . If you must use
you r brakes, do not hold the bra kes down cont in­
u o usly. Pump the brakes at in tervals.
Operating noise
Noises may occur when braki ng depending on the
speed, braking force and outs ide cond it ions such
as tempera ture and hum idity.
Due to the nature of the materia ls used i n ceram­
i c brake rotors*, noises may become more appa­
r ent at low speeds.
Effect of water and road salt
In certa in situations, for examp le after driv ing
through water , in heavy rain, after overnight con­
densation or after washing your car, the braking
effect can be reduced by moisture or ice on the
brake rotors and brake pads . The brakes must be
dr ied fi rst w ith a few careful b rake app lications.
At higher speeds and with the windsh ield wipers
turned on, the brake pads press against the brake r otors for a short amount of time. This occurs at
r egular intervals without the dr iver not ic ing and
provides fo r be tter brake response time under
wet cond it ions.
The effect iveness of the brakes ca n be red uced
when the v ehicle is d riv en on a salt-cove red road
and the b rakes are no t used. Likewise, you clean
off a ccumula ted salt coating from b rake d iscs
and pads with a few ca utious app lications of the
brake ¢& .
D ue to the ir sur fa ce character istics, cerami c
brake ro tors * absorb moistu re in such co ndi tions . ..,.

Intelligent technology
Rear spoiler
The rear spoiler improves vehicle handling and
enhances driver control.
SPORT •
Fig. 127 Switch for rear spoiler
The rear spoiler deploys and retracts. Spo iler op­
eration can be set for automatic or manual oper­
ation.
Automatic mode (normal operation)
-Extending automatically: This occurs when driv­
ing faster than approximately
62 mph (100
km/h) or at a certain engine compartment tem­
perature1l.
- Retracting automatically: This occurs when
driv ing s lower than approximate ly
22 mph (35
km/h) or at a certain engine compartment tem­
perature1l.
Manual mode
- Extending manually: Press the switch
~ fig. 12 7 briefly to extend the rear spoi ler
completely.
- Retracting manually: When dr iving at speeds
below approximately
12 mph (20 km/h), press
and hold the switch to retract the rear spoiler.
When dr iving at speeds between
12 mph and
62 mph (20 km/h and 100 km/h), press the
switch briefly to retract the rear spoiler com­
pletely. You cannot retract the rear spoiler if it
extended due to the engine compartment tem­
perature.
1 > The rear spoiler only extends or retracts above a certain
e ngine temperature in some mode ls.
138
Indicator light
When the indicator light I-· appears, there is a
system malfunction. The rear spoi ler may not be
able to extend. This could change the vehicle's
driving character istics at high speeds. Do not ex­
ceed 87 mph
(140 km/h). Drive to your author­
i zed Audi dealer immediately to have the mal­
function corrected.
A WARNING
-
Driving at h igher speeds without the rear
spoiler deployed can impair handling charac­
ter istics, making the vehicle harder to control.
- Improper operation of the rear spoiler can
cause crushing injuries. A lways make sure
that nobody , especial ly children, is in the
way when the rear spoiler is deployed or re­
tracted.
- Always obey speed limits and other traffic
laws.
- Hot air from the engine compartment can
escape through the rear spoiler when it is
open and it could burn you.
(D Note
-Never push the vehicle or apply force to the
rear spoiler -it could be damaged.
- To prevent damage to the rear spo iler do
not lean or place anything on it.
- Only operate the rear spo iler manually when
the engine compartment lid is closed and
the rear spoiler moving parts are not
bloc ked. Otherwise, damage could occur.
(D Tips
Clean the spoiler compartment every 2 to 3
months. The spoiler compartment must al­
ways be free of ice, snow, leaves or other de­
bris.

..... N
r-­N "': ..... \!) 1.1'1
N 1.1'1 .....
What you should know
The highest priority is given to maintaining start­
ing capability .
The battery is severely taxed in short-distance
driving, in city traffic and during the cold time of
year . Abundant electrical energy is required, but
only a little is generated . It is also critical if the
engine is not running and electrical components
are turned on. In this instance energy is being
consumed but none is being generated.
It is in precisely these situations that you w ill no­
tice energy management actively regulating the
d istribution of ene rgy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period of
several days or weeks , electr ical components are
gradually cut back or switched off . This reduces
energy consumption and maintains starting ca­
pability over a longer pe riod .
Take into consideration that when you unlock
your veh icle, some convenience functions, such
as the remote key or power seat adjustment, may
not be available. The convenience functions will
be available again when you turn on the ignition
and start the engine .
With the engine turned off
If you listen to the radio, for example, with the
engine turned off, the battery is being dis­
charged .
If starting capability is jeopardized due to energy
consumption, a message appears in the driver in­
formation display .
You have to start the engine to charge the bat ­
tery .
With the engine running
Although electrical energy is generated when the
vehicle is being driven, the battery can become
discharged. This happens mostly when little en­
ergy is be ing generated and a great deal con­
sumed and the battery's state of charge is not
optimal.
Intelligent technology
To bring the energy balance back into equilibri­
um, consumers which require especially large
amounts of energy are temporar ily cut back or
switched off. Heating systems in part icu lar re­
quire a great deal of energy. If you notice, for ex­
ample, that the heated seats* or the heated rear
window are not heating, they have been tempo­
rarily cut back or switched off . These systems w ill
be available again as soon as the energy balance
has been restored.
You w ill also not ice that engine idle speed has
been increased slightly . This is normal and not a
cause for concern. By incr easing eng ine idle
speed the additional energy required is generated
and the battery is charged.
Driver notification in the instrument
cluster display
If battery power drops in to the range where it
can limit the ability of the engine to start, this is
shown in the instrument cluster display w ith the
following driver message :
[•] low battery charge: battery will be charged
while driving
This notification reminds you that the starting
capability of the engine may be limited. As soon
as you start driving again, the battery will be re­
charged and the notificat ion will go out .
Driver notification appears and goes out
again
If this driver notification appears after the igni­
tion is turned on or while driv ing and it goes out
again after a while, the battery has been ade ­
quately recharged .
Driver notification appears and does not go
out again
If this driver notif ication appears after the ign i­
t ion is turned on or while dr iv ing and does not go
out again, the battery's state of charge is not in
t h e optimal range. Starting ability is restricted .
Have the battery checked as soon as possible by
an authorized Audi dea le r or qualified workshop.
141

Driving and en vironment
Driving and environment
Break-in period
A new vehicle must be broken in, and the break-in
period shou ld be 1 ,500 miles (2,500 km) . Do not
use full acceleration for the first 600 miles
(1 ,000 km) and do not exceed the maximum en­
gine speed of 6,000 rpm You must also not use
full accelerat ion between 600 and 1,200 miles
(1,000 to 2,000 km) . From 1,200 to 1,500 miles
(2 ,000 to 2,500 km), you can gradually increase
maximum eng ine speed to 8,250 rpm for brief
pe riods.
During the first hours of operation, there is
greater fr iction in the eng ine and the transmis­
sion than later when all the moving pa rts have
b roken in .
The way you drive during the first 1,500 miles
(2 ,500 km) affects engine quality . If you drive at
modera te engine speeds thereafter, part icu larly
when the engine is cold, yo u red uce eng ine wea r
and increase the potential mileage o f the engine.
Do not dr ive at RPMs that a re too
low. Shift down
when the engine is no longe r runni ng "smooth­
ly". Extremely high RPMs are gover ned automati­
cally.
Avoid damaging the
vehicle
W hen you are driving on poor roads, or over
curbs, steep ramps, etc ., make certain that low­
lying parts such as spoilers and exhaust system
parts do not bottom out and get damaged .
This is especially true for vehicles with low-slung
chassis (sports chassis) and fully loaded vehicles.
Driving through water on
roads
Note the following to avoid vehicle damage when
d riving through water, for examp le on flooded
roads:
- The water must no t be any h igher than the bot­
tom of the vehicle body.
142
- Do not drive faster than walk ing speed .
A WARNING
After driv ing through water, mud, s lush, etc .,
the brakes may be s low to take effect because
of wet brake rotors and pads. Dry the brakes
first by brak ing carefully to restore the full
braking effect.
(D Note
Vehicle components such as the eng ine,
transmission , suspension or e lectrical system
can be severe ly damaged by dr iv ing t hrough
water .
(D Tips
- Check the dept h of the water before driving
through it.
- Do not stop the vehicle, drive in reverse or switch the engine off when driv ing through
water.
- Keep in mind that oncoming veh icles may
create waves that raise the water level and
make it too deep for your vehicle to d rive
through safely .
- Avoid driving through salt water because it
can cause corrosion.
Catalytic converter
It is very important that your emission control
system (catalytic converter) is functioning prop­
erly to ensure that your vehicle is running in an
environmen tally sound manner.
.,. Always use lead-free gasoline ~ page 151,
Fuel supply.
.,. Never r un the tank down all the way to empty.
.,. Never put too much mo tor o il in yo ur engi ne
~ page 160, Adding engine oil 'l::r..
.,. Never try to push- or tow-sta rt your vehicle .
The cata lytic converter is an effi cien t "clean -up"
device built in to the exhaust system of the vehi ­
cle. The cata lytic conve rter burns many of the
po llutants in the exhaust gas before they are re­
l eased into the atmosphere.
-

.....
Vehicle care and cleaning General information
Regular, proper care helps to maintain your vehi ­
cle's value.
It can a lso be a req uirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from your authorized Audi dea ler or a
qualified workshop. Read and follow the instruc­
tions for use on the packaging.
A WARNING
-Us ing clean ing and care products incorrectly
can be dangerous to your health.
- Always store cleaning and care products out
of reach of children to reduce the r isk of poi­
soning.
@ For the sake of the environment
- Preferably use environmentally-friendly products when buying cleaning agents.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer deposits remain on the vehicle, the
more the surface can be damaged. High tempera­
tures such as those caused by sunlight increase
the damaging effect .
Before washing, wet heavy deposits with plenty
of water.
Stubborn depos its such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth .
A lso, was h the underside of your vehicle once
road salt stops being used for the season.
Pressure washers
When washing your veh icles w ith a pressure
washer, always follow the operating instructions
"' provided with the pressure washer. This is espe-
r--
~ cially important in regard to the pressure and
; spraying distance . Do not aim the spray directly
~ at seals on side windows, doors, the engine com -,.... Vehicle care and cleaning
partment lid, the front lid
or the convertible top
or at tires, rubber hoses, insulating material
orsensors* or camera lenses *. Keep a distance of
at least 16 inches (40 cm).
Do not remove snow and ice with a pressure
washer .
Never use rotary nozzles or high pressure noz­
zles.
The water temperature must not be above 140 °F
(60 °().
Automatic car washes
Spray off the veh icle before washing.
Make sure that the windows are closed and the
windshield wipers are off. Follow instructions
from the car wash operator, especially if there are
accessor ies attached to your vehicle .
If possible, use car washes that do not have
brushes .
Only use car washes where the vehicle remains
stationary and the washing equipment moves
around t he vehic le when washing and drying. Car
washes that move the vehicle through the car
wash using a chain are not recommended.
Washing by hand
Clean the vehicle starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning prod ucts .
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi ­
cle. Insects, grease spots and fingerprints are
best removed with a spec ia l cleaner for matte
finish paint.
Apply the prod uct using a microfiber cloth . To
avo id damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
c lean using a neutral shampoo and a soft micro­
fiber cloth.
Rinse the vehi cle thoroughly again and let it air
dry. Remove any water residue using a sham my . .,.
145

..... N
r-­N "": ..... \!) 1.1"1
N 1.1"1 .....
Vehicle care and cleaning
Component S ituation Solution
Ex haust t ail
Road sa lt Water, cleaning
solution suitable for stainless steel, if nee-
pip es essary
Power to p Dirty Clean water, power top clean ing product, if necessary .
C lean with the gra in of the fabr ic using a soft brush and al-
l ow to air d ry .
W ind d efle ct o r Dirty Water, mild soap solutiona), if necessary
Decorati ve p arts/ Dirty Mild soap solution al, a cleaning so lution suitable for stain-
trim less stee l, if necessary
P ai nt Paint damage Refer to the pa int number on the vehicle data label, repair
with touch up paint ~
page 212
Spilled fuel Rinse with water immediately
Rust fi lm Rust film remover, then protect with hard wax; for ques-
tions, refer to an authorized A udi dealer or a q ualified
workshop
Corrosion Have it removed by an authorized Audi dealer or a qualified
workshop
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitab le polish; then apply paint p rotectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith water immediatedly and remove w ith a mi-
sects, bird dropp ings, crofibe r cloth
tree sap and road sa lt
Grease-based con-Remove immediatedly w ith a mild soap solutional and a
taminants such as soft cloth
cosmetics or sunblock
C ar bon p art s Dirty Clean the same way as painted parts~ page 145, Car
washes
D ecorativ e decal s Dirty Soft
sponge with a mild soap solutiona)
aJ Mild soap solution: max imu m two tablespo ons n eutral soap in 1 quart (I lite r) of water
Cle anin g int erior
Compon ent Situation Solution
Windo ws
Dirty
Glass cleaner, then wipe dry
Deco rative Dirty Mild soap solutional
parts/
trim
Pl as tic par ts
Dirty Damp cloth
Heavily soiled Mild soap solutional, solvent-free plastic clea ning so l-
u tion, if necessary
147

Vehicle care and cleaning
Component Situation Solution
Displays
Dirty Soft cloth with LCD cleaner
Controls Dirty Soft brush, then a soft cloth with a mild soap solu-
tional
Safety belts Dirty Mild soap solution a>, allow to dry before letting them
retr act
Textiles, Stains adhering to the sur- Vacuum cleaner
Vinyl, face
Alcantara Water-based stains such as Absorbent cloth and mild soap solutional
coffee, tea, blood, etc.
Oil-based stains such as o il, Apply a mi ld soap solutiona>, blot away the disso lved
make-up, etc. oil ori dye, treat afterward with water, if necessary
Special stains such as ball- Special stain remover, blot with absorbent material,
point pen, nail polish, latex treat afterward with mild soap solutional, if necessary
paint, shoe polish, etc.
Natural leather Fresh stains Cotton cloth with a mild soap solutional
Water-based stains such as
Fresh stains: absorbent cloth
coffee, tea, blood, etc. Dried stains: stain remover suitable for leather
Oil-based stains such as oil, Fresh stains: absorbent cloth and stain remover suita-
make-up, etc. ble for leather
dried stains: Oil cleaning spray
Special stains such as ball- Stain remover suitable for leather
point pen, nail polish, latex
paint, shoe polish, etc.
Care Reg
ula rly apply conditioning cream that protects
from light and penetrates into the materia l. Use spe-
cially-co lored conditioning cream, if necessary.
Carbon parts Dirty Clealil the same way as plastic parts
aJ Mild soap so lution: max im um two ta blespoo ns neut ral so ap in 1 quart (l lite r) of w ate r
A WARNING
Th e windshie ld may not be treated with wa­
ter-repelling windshield coating agents. Un­
favorable conditions such as wetness, dark­
ness, or low sun ca n resu lt in increased glare.
Wiper blade chatter is also possible .
(D Note
-Headlights/tail lights
- Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcohol, because they could cause
cracks to form.
-Wheels
148
-
- Never use any paint polish or other abra­
sive materials.
- Damage to the protective layer on the
r ims such as stone chips or scratches must
be repaired immed iately.
-Sensors/camera lenses
- Never use warm or hot water to remove
snow or ice from the camera lens. This
could cause the lens to crack.
- Never use abrasive clean ing materials or
a lcohol to clean the camera lens. This
could cause scratches and cracks.
- Power top
- Remove bird droppings immediately .

Fuel supply and filling your fuel tank
fill up at busy gas stations where the seasonal
adjustment is more like ly to be made in time.
0 Note
- Methanol fuels which do not meet these re­
quirements may cause corrosion and dam­
age to plastic and rubber components in the
fuel system.
- Do not use fuels that fail to meet the spec i­
fied criteria in this chapter.
- If you are unable to determine whether or
not a particular fuel blend meets the speci­
fications, ask your service station or its fuel
supplier.
- Do not use fuel for which the contents can­
not be identified.
- Fuel system damage and performance prob­
l ems resulting from the use of fuels differ­
ent from those specified are not the respon­
sibility of Audi and are not covered under
the New Vehicle or the Emission Control
System Warranties.
- If you experience a loss of fuel economy or
driveability and performance problems due
to the use of one of these fuel blends, we
recommend that you switch to unb lended
fuel.
Gasoline additives
A major concern among many auto manufactur­
ers is carbon deposit build-up caused by the type
of gasoline you use.
A lthough gasol ine grades differ from one manu­
facturer to another, they have certain things in
common. All gaso line grades contain substances
that can cause deposits to collect on vita l engine
parts, such as fuel injectors and intake valves. A l­
though most gasoline brands include additives to
keep engine and fuel systems clean, they are not
equally effect ive .
Audi recommends using TOP TIER Detergent Gas­
oline. For more information on TOP TIER Deter­
gent Gasoline, please go to the official website (www.toptiergas .com).
152
After an extended period of using inadequate
fuels, built-up carbon deposits can rob your en­ gine of peak performance .
([) Note
Damage or malfunction due to poor fuel qual­
ity is not covered by the Audi New Vehicle
Limited Warranty.
Fuel tank
· Fuel filler neck
The fuel filler neck is located on the right rear
s id e panel behind the fuel filler flap.
If the unlocking system should fail, you can still
open the flap manually -for detailed instructions
see
~page 154.
You can find the fuel tank capacity of your vehicle
i n
Technical Data .
The label on the inside of the fuel filler flap tells
you the correct fuel for your vehicle. For more in­
formation about fuel specifications, see
~ page 151 .
Your vehicle fue l tank has an on-board refueling
vapor recovery system. This feature helps to pre­
vent fuel vapors from escap ing from the tank and
polluting the environment while you refuel your
vehicle. In order to fill the tank properly while
protecting the environment, please follow this
refueling procedure carefully.
& WARNING
-Under normal operating conditions, never car­
ry additional fuel containe rs in your car . Gas
canisters and other containers used to trans­ port f uel can be dangerous. Such containers,
full or empty, may leak and could cause a fire
in a collision. If you must transport fuel to
use for your lawn mower, snow blower, etc., be very careful and always observe local and
state laws regarding the use, transpo rtation
and storage of such fuel containers. Make cer­
tain the container meets indus try s tandar ds
(ANSI/ASTM F8S2 -86).