
44 Clear vis ion
Inter ior lighting
There are other in ter ior light ing f unct ions
that are available. Individual functions can be
adj usted i n the MM I. Se lect: ICARlf unction
button >
Systems or Car Sy stems control but
ton>
Vehicle settings > Interior lighting .
Instrument illumination
The basic brightness of the illum inat ion for
the instruments, the c enter console and the
display can be adjus ted.
F ig . 40 In st rumentenbeleu chtung
.,. Turn the thumbwhee l up or down to red uce
o r i ncrease t he brightness level.
(D Tips
The instrument ill umination (for dia ls and
needles) lights on when the ig nition is
sw itched on and the vehicle lig hts are
t urned off. As the dayligh t fades, the ill u
m ina tion of the dials likew ise dims auto
matically and will go out comp lete ly when
the outside light is very low . This feat ure is
meant to remind you to switch on the
headlights when outside lig ht conditions
become poor.
Vision
Adjusting the exterior mirrors
F ig. 41 Forwar d sect io n of dr ive r's armrest: powe r mir
r or control s
Turn the knob to the desired pos it io n:
Turn the knob to the des ired posit ion:
Q/P -In this position , yo u can adjust the
driver 's and front passenger's exterior mirrors
by turning the k nob i n the desired direction .
Qiil -The mirrors are heated depending on the
outside temperature .
8 -T he ex terior m ir rors fold in* if you turn
t h e knob into this position wit h the ignition
switched on .
Passenger exterior mirror tilt function*
To he lp you see the curb when ba ck ing into a
par king space, the surface of the mirror tilts
s li ght ly. The knob must be in the P posi tion
f or this to happen .
You can adjust the tilted m irror surface by
tu rning the knob in the desired direction.
When you move out of reverse and in to anoth
er gear, the new m irror position is s to red and
ass igned to the key you are using.
T he m irror goes ba ck i nto its orig inal position
once you dr ive forward faster than 9 mph
(15 km/h) o r swi tch the ig nition off .
A WARNING
Curved m irror surfaces (co nvex o r spheri
cal*) increase your f ie ld of view. Remem
ber that veh icles or other ob jects will ap
p ear smaller a nd farther away tha n when
seen in a flat mirror . If you use t his mi rror
-

M N M N
0 ::i co
rl I.O
"' rl
"' rl
to estimate distances of following vehicles
when changing lanes, you could estimate incorrectly and cause an accident.
(D Note
- If the mirror housing is moved uninten
tionally (for example, while parking your
vehicle), then you must first fold the mir ror electrically. Do not readjust the mir
ror housing manually. You could damage
the motor which controls the mirror .
- If you wash the vehicle in an automatic
car wash, you must fold the exterior mir
rors in to reduce the risk of damage to
the mirrors. Never fold power folding ex
terior mirrors* by hand. Only fold them
in and out using the power controls.
@ Tips
If there should be a malfunction in the
electrical system, you can still adjust the
exterior mirrors by pressing the edge of
the mirror ..
Dimming the mirrors
Fig. 42 Automatic dimming rearview mirror•
Manual dimming rearview mirror
.,. Pull the lever at the bottom of the mirror
back.
Automatic dimming rearview mirror* .,. Press the button
@r::;, fig. 42. The indicator
light @ turns on. The rearview and exterior*
mirrors dim automatically when light shines
on them, for example from headlights on a
vehicle to the rear .
Clear vision 45
A WARNING
Electrolyte fluid can leak from automatic
dimming mirrors if the glass is broken.
Electrolyte fluid can irritate skin, eyes and
respiratory system.
- Repeated or prolonged exposure to elec trolyte can cause irritation to the respira
tory system, especially among people
with asthma or other respiratory condi
tions. Get fresh air immediately by leav
ing the vehicle or, if that is not possible,
open windows and doors all the way.
- If electrolyte gets into the eyes, flush
them thoroughly with large amounts of clean water for at least 15 minutes; medical attention is recommended.
- If electrolyte contacts skin, flush affect
ed area with clean water for at least 15
minutes and then wash affected area
with soap and water; medical attention is recommended. Thoroughly wash af
fected clothing and shoes before reuse.
- If swallowed and person is conscious,
rinse mouth with water for at least 15
minutes. Do not induce vomiting unless
instructed to do so by medical professio
ncil. Get medical attention immediately.
(D Note
Liquid electrolyte leaking from broken mir
ror glass will damage any plastic surfaces
it comes in contact with. Clean up spilled
electrolyte immediately with clean water
and a sponge.
(D Tips
-Switching off the dimming function of
the inside rear view mirror also deacti
vates the automatic dimming function of
the exterior mirrors.
- Automatic dimming for the mirror only
operates properly if the light striking the
inside mirror is not hindered by other ob
jects.
- The automatic dimming mirrors do not
dim when the interior lighting is turned
on or the reverse gear is selected.
.

46 Clear vis ion
Sun visors
Fig. 43 Drive r's side : sun visor
The sun v isors for the driver and passenger
can be pulled out of the ir brackets in the cen
ter of the vehicle and turned towards the
doors @.
The mirror light switches on when the cover over the vanity mirror @opens .
Wiper and washer
system
Switching the windshield wipers on
Fig. 44 Wind sh ie ld wipe r lever
Fi g. 4 5 O pera ting rear window w ipe r
" -0
='> a, a,
Move the windshield wiper lever to the cor re
spond ing pos ition:
@ -Windsh ie ld wiper off
(D -Interval mode. To extend/shorten the
wipe r intervals, move the switch @to the
l eft/r ight . In vehicles with a ra in sensor* the
wipers turn on in the rain once the vehicle
speed exceeds approximately 2 mph (4 km/h).
The higher the sensit iv ity of the ra in sensor* is
set (switch @to the right), t he earlier the
windshield wipers react to moisture on the
windshield .
@ -Slow w iping
@ -Fast wip ing
@ -Sing le wipe . If you ho ld the lever in this
position, the wipe rs will switch from slow con
tin uous wiping to fast cont inuous wiping after
a while.
® -C lean the w indshie ld. To elim ina te water
droplets, the windshield wiper performs one
afterwipe operation after severa l seconds
whi le driving. You can sw itch this function
off
by moving the lever to posit ion ® within 10
seconds of the afterwipe operat ion. The after
wipe function is reactivated the next t ime the
ignition is sw itched on.
® -Rear wipe. The rear w indow is wiped ap
proximately every 6 seconds.
(j) -Rear wash/wipe . The n umber of wiper cy
cles depends on how long you hold the lever
in position
(J) .
A WARNING
-The rain sensor is only intended to assist
the dr iver. T he d river is st ill responsib le
for manually switching the wipers on ac
cording to the visibility cond itio ns.
- The windsh ield may not be treated with
wate r-repell ing windsh ield coating
agen ts. Un favo rable cond it ions, such as
wetnes s, dark ness, low su n, c an result in
i n creased glare. Wipe r blade cha tter is
also possib le .
- Prope rly fun ct ion ing wi ndsh iel d wiper
b la d es are req uired for a clea r view and
safe driving
c:> page 47, Replacing
windshield wiper blades .

M N
M N
0 ::i co ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
(D Note
-In the case of frost , check whether the
windsh ield wiper b lades are frozen to
the windshie ld. Switching on the wind
s hi eld wipers can damage the wiper
blades!
- Prior to using a car wash, the windshield
wiper system must be switched
off (lever
i n position @). This helps to prevent un
i ntent ional sw itch ing on and damage to
the windshie ld w iper system .
- The wi ndshield wipe rs are switched
off
whe n the ignition is turned off . Activate
t h e w indshie ld w ipers afte r the ig nit ion
i s sw itche d back on by mov ing the w ind
s hi eld wipe r lever to any pos ition.
- Worn or di rty windshie ld wiper b lades
r es ult in strea king. This can affe ct the
r ain senso r* func tion . C heck your wind
s h ield wiper blades r egularly.
- The w asher fluid nozzles of the wi nd
s hi eld washer system are heated a t low
temperatures w hen the ignit ion is on .
- W hen stopp ing tempor arily, (e.g. a t a
traff ic light) the se t speed of the w ind
s hi eld wipers is automatically red uced by
one speed .
Cleaning windshield wiper blades
Clean the windshield wiper blades whe n they
begin to leave streaks . Use a soft cloth and
g lass cleaner to clean the windsh ield wiper
b lades .
Windshield wiper s
.. Place the windshield wipe r arms in the serv
ice position . Refer to ¢ page
47 .
.,. Lift the w iper arm away from the front win
dow .
Rear window wiper
.. Lift the rear wiper arm away from the glass.
Clear vis ion 4 7
A WARNING
Dirty winds hield wiper b lades can impair
your v iew. This can lead to accidents .
Replacing windshield wiper blades
Fig. 46 Remov ing w indsh ield w iper blade
Wiper service position /blade replacement
position
.. Switch the ignit ion off and move the wind
shield w iper lever to position ©¢ page
46,
fig .
44.The w indshie ld w ipers move into the
service pos ition .
.. To br ing the w ipers back into the original
position, sw itc h th e ignition on and p ress
t he winds hield wipe r leve r.
Removing the wiper blade
.. Lift the windsh ield w iper arm up from the
w indshield .
.. Press the lock ing knob
.,. Remove the wipe r blade in the di rec tion of
t he ar row .
Attaching the wiper blade
.. Insta ll the new wiper blade in the reta iner
on t he wiper arm @until you hear i t click in
to p lace on the w iper arm .
.,. Place t he w iper arm back on the winds hield.
.. To bring the w ipers b ack into the or igin al
position, switch the ignition on and press
the windshield wipe r lever.
A WARNING
-
For your safety, y ou shou ld rep lace the
wiper b lades once or twice a year. See your

M N M N
0 ::i co
rl I.O
"' rl
"' rl
Removing the head restraints
• Fold the backrest forward
¢ page 60 .
• Move the head restraint upward as far as it
can go.
• Press the release@¢
fig. 54 with an auxili
ary tool and the button @. Pull the head re
straint out of the backrest at the same time
¢ & .
Install ing the head restraints
• Slide the posts on the head restraint down
into the guides until you feel the posts click
into place .
• Press the button @ and slide the head re
stra int all the way down. You should not be
able to pull the head restraint out of the
back rest.
So that the driver can have a better view to
the rear, the head restraints should be pushed
down completely when the rear seats are not
occupied.
_& WARNING
- Only remove the rear seat head restraints
when necessary in order to install a chi ld
seat . Install the head restraint again im
mediately once the child seat is removed.
Driving without head restraints or with
head restraints that are not properly ad
justed increases the risk of serious or fa
tal neck injury dramatically .
- Read and heed all WARNINGS
¢ page 9 7, Proper adjustment of head
restraints .
(D Tips
Correctly adjusted head restraints and
safety belts are an extremely effective
combinat ion of safety features.
Seats and storage 53
Ashtray
Applies to vehicles: with ashtray
Fig. 55 Center console: Asht ray
The ashtray can be inserted in one of the two
front cup holders .
• To open the ashtray, lift the lid.
.,. To empty the ashtray, lift it out of the cup
holder . After emptying the ashtray , make
sure that you insert it again so it is seated
securely .
_& WARNING
Never put waste paper in the ashtray. Hot
ashes or other hot objects in the ashtray
could set waste paper on fire .
Cigarette lighter
Applies to vehicles: with cigarette lighter
Fig. 56 Front ce nter console: C iga rette l ighte r
.. Open the cover .
.. Press in the cigarette lighter .
.,. When the cigarette lighter spr ings out, p ull
it out completely.
II>

54 Seats and storage
A WARNING
T he ciga rette lighter only works when the
ign ition is on . Improper use can cause seri
ous injury or start a fire. To avo id the r isk
of injury, nev er leave children unsupe r
vised in the vehicle with the key.
12-volt sockets
Ap plies to vehicles: with 12 -volt socket
Fi g. 57 Fro nt cen ter conso le: 12 Vo lt socket •
Fig. 58 R ear ce nter c onso le: 12 Vo lt socket
.. Open the socket cover ¢ fig. 57 or¢ fig. 58 .
.. Insert the p lug of the e lectrica l device into
the socket.
The 12 -volt sockets can be used fo r electr ical
accessories. The power input must not exceed
120 watts.
There is an addi tional 12-vo lt socket in the
center console .
Before you purchase any accessories, always
read and fo llow the informa tion in
¢ page 239, Additional accessories and parts
r e plac em ent .
A WARNING
The power out lets and therefore the elec
trical accessories connected to them oper- ate only with the ignit
ion on. Improper use
of the outlets or of electrical accessories
can lead to ser ious injuries or cause a fire.
For this reason, children should never be
l eft unattended in the vehicle -they could
be injured!
(D Note
To avoid damaging the socket, only use plugs that fit properly .
(D Tips
When the engine is off and accessories are
still plugged in and are on , the vehicle bat
tery can still be drained .
Storage
General overview
A WARNING
--
-Always remove objects from the instru
ment panel. Any items not put away
could slide around ins ide the veh icle
while driving or when ac cele rat ing o r
when applying the brakes or when dr iv
ing arou nd a corne r.
- When you are dr iving make s ure that
an yth ing you may have pla ced in the cen
ter conso le or other storage loca tions
cannot fall out into the footwe lls . In case
of sudden braking you would not be able
to brake or accelerate.
- Any pieces of clothing that you have
hung up must not i nterfere with the dr iv
er's view. The coat hooks are des igned
only for lightweight cloth ing . Never hang
any cloth ing with hard, pointed o r heavy
objects in the pockets on the coat hoo ks .
During s udden braking or in an accident -
especia lly if t he a irbag is deployed -
these objec ts co uld in ju re any passen
ge rs inside the ve hicl e.

56 Seats and storage
in the vehicle while it is moving. In case
of an accident, sudden braking or other
vehicle movement, hot liquid could spill,
causing scalding burns . Spilled hot liquid
can also cause an accident and personal
injury.
- Use only soft cups in the cupholder. Hard
cups and glasses can cause injury in an
accident .
- Never use the cupholder or adapter as an
ashtray -risk of fire .
CD Note
Only drink containers with lids should be
carried in the cupholder . Liquid could spill
out and damage your vehicle's electronic
equipment or stain the upholstery, etc.
(upholders in the door pockets
There is a cupholder in all four doors .
Fig. 63 Sect ion of doo r panel: Cupho lder
The cupholders in the door pockets are suita
ble for 1 to 1.5-liter bottles.
_& WARNING ,~ ~
Spilled hot liquid can cause an accident
and personal injury.
- Never carry any beverage containers with
hot liquids, such as hot coffee or hot tea,
in the vehicle while it is moving. In case
of an accident, sudden braking or other
vehicle movement, hot liquid could spill,
causing scalding burns. Spilled hot liquid
can also cause an accident and personal injury . -
Use only soft cups in the cupholder. Hard
cups and glasses can cause injury in an
accident.
CD Note
Only drink containers with lids should be
carried in the cupholder. Liquid could spill
out and damage your vehicle's electronic
equipment or stain the upholstery, etc.
Additional storage
There are a variety of storage compartments
and fasteners in various places in the vehicle .
- In the front center console.
- At the front end of the front seats*. You can
store objects weighing up to 1.5 kg in the
drawer and objec ts weighing up to 1 kg in
the hinged compartment .
- In the door trim.
- Coat hooks next to and above the rear doors.
- Nets* on the backrests of the front seats.
- Coat hooks/retaining hooks in the luggage
compartment.
A WARNING
- When driving, do not leave any hard ob
jects on the rear window shelf or allow
your pet to sit on the shelf. They could become a hazard for vehicle occupants in
the event of sudden braking or a crash .
- Always remove objects from the instru
ment panel. Any items not stored could
slide around inside the vehicle while driv
ing or when accelerating or when apply ing the brakes or when driving around a
corner .
- When you are driving make sure that
anything you may have placed in the cen
ter console or other storage locations
cannot fall out into the footwells. In case
of sudden braking you would not be able
to brake or accelerate.
- Any articles of clothing that you have
hung up must not interfere with the driv
er's view. The coat hooks are designed
only for lightweight clothing. Never hang
~

M N M N
0 ::i co
rl I.O
"' rl
"' rl
any clothing with hard, pointed or heavy
objects in the pockets on the coat hooks.
During sudden braking or in an accident -
especially if the airbag is deployed -
these objects could injure any passen
gers inside the vehicle .
- To reduce the r isk of personal injury in an
acc ident or sudden stop, always keep the
glove compartment closed while driving.
- Read and follow all WARNINGS
Q page 129, Important safety instruc
tions on the side airbag system.
- Hang clothes in such a way that they do
not impair the driver's v ision.
- The coat hooks must only be used for
lightwe ight cloth ing . Do not leave any
heavy o r sharp edged objects in the pock
ets which may interfere with the side cur
tain a irbag deployment and can cause
persona l injury in a crash .
- Do not use coat hangers for hanging
clothing on the coat hooks as this can in
terfere with proper dep loyment of the
side curtain airbags in an accident .
- Do not hang heavy objects on the coat
hooks, as they cou ld cause persona l in
jury in a sudden stop.
- Always keep the compartment above the
rearview mirror closed whi le driving to
reduce the risk of injury in the event of
sudden braking maneuvers or a collision.
(D Note
Objects located on the rear shelf that rub
against the rear w indow cou ld damage the
heating wires for the rear window defog
ger.
@ T ips
- A vent slot is located between the shelf
and the rear window. Do not b lock the
vent with any items you may place on the rear window shelf.
- Do not p lace bulky items on the rear w in
dow shelf as they could restrict or b lock
the driver's vis ion in the rear view mirro r.
S ea ts a nd s to rage 57
Description and
mounting locations
Additional cargo can be carried with a roof
luggage rack.
Fig . 64 Roof rack attachment points
.,. Always read and follow the instructions pro
vided by the roof rack manufacturer when
installing the roof rack system .
If luggage or cargo is to be carried on the
roof, you must observe the following:
- On ly use roof racks approved for your vehi
cle. These approved roof racks are the basis
for a complete roof rack system. Additional attachments or carr ier systems are needed
to transport luggage and sports equipment .
We recommend using roof racks from the
Audi original accessories program.
- When installing the roof rack, make sure it
is only mounted on the designated locations
on the roof
Q fig. 64.
-We recommend that you keep the installa
tion instructions for your roof rack system
together with your Owner's literature in the
veh icle .
Wh en sh ould th e roo f rack be re mov ed ?
-Before going through an automatic car wash
(it is best to ask the car wash operator for
advice).
- When not in use, to reduce fuel consump
tion, wind noise and to guard against theft.
A WARNING
-
-Use of an unapproved roof rack or incor-
rect mounting of an approved roof rack
can cause the roof rack or the items