2015 AUDI A8 ignition

54 Clear vis ion
rain se nsor f unction . Check yo ur
winds hield wiper b lades regularly.
- The washer fluid nozzles of the wind­
sh ield washer system are heated at low
temperatures when the ignition is on .
- When stopping temporarily, e .g . at a
traffic light, the set speed of the wind­
s h ield wipers is automatically red uced by
one speed.
Cleaning w indshield wiper blades
Clean the w indshield wiper blades when they
begin to leave streaks . Use a soft cloth and
g lass cleaner to clean the windsh ield wiper
b lades.
.. Place the windshield wiper arms in the serv­
ice position . Refer to ¢
page 54.
.. Lift the w iper arm away from the front win­
dow.
_& WARNING
Dirty w indshie ld w iper blades can impa ir
your view. Thi5 can lead to acc ident5 .
Replacing windshield wiper blades
Fig. 52 Removi ng w inds hield w ipe r blades
Wiper ser vice position / Blade
replacem ent position
-
.. Switch the ign ition off and move the w ind­
shield wipe r leve r to posi tion @ ¢
page 53,
fig. 51. The windshield wipe rs move into the
service position.
.. To bring the wipe rs back into the original
position, switch the ignition on and press
the windshie ld wiper lever. You can also t
urn the se rv ice position on or off
in the MMI:
.. Switch the windshie ld wipers
off (position
@ ¢page 53, fig. 51) .
.. Select: !CARI function button> Car systems
contro l butto n > Serv icing & checks > Wip er
serv ice position
> On.
R emo ving the wipe r blade
.. Lift the windshield wiper arm up from the
w indshield.
.. Press the locking knob
(D ¢ fig. 52 on the
w iper blade. Hold the wiper blade firmly .
.. Remove the wipe r blade in the d irection of
the arrow .
Attaching the wipe r blade
.. Insta ll the new wiper blade in the reta iner
on the wiper arm @unt il you hear it click in­
to place on the w iper arm .
.. Place the w iper arm back on the windshield .
.. Tu rn the se rvice position
off.
_& WARNING
-
F or your s afety, you shou ld rep lace the
wiper b lades once or twice a yea r. See your
a uthorized Audi dea ler fo r replacement
b lades .
(D Note
- The windsh ie ld wiper b lades m ust only
be folded away when in the service posi­
tion! Otherwise, yo u ris k damaging the
paint on the hood or the windshie ld w ip­
er motor.
- Yo u should not move your vehicle or
press the windshie ld wiper lever when
the wiper arms are folded away from the
windshield. The windsh ield wipers wou ld
move back into their or iginal position
and co uld damage the hood and wind­
shield.
- To help prevent damage to the w iper sys­
tem, always loosen blades w hich are fro­
zen to the windshield before operating
w ipers. .,.

-To help prevent damage to wiper b lades,
do not use gasoline, kerosene, paint
th inner, or other solvents on or near the
wiper blades.
- To he lp prevent damage to the wipe r
arms or other components, do not at ­
tempt to move the wipers by hand.
@ Tips
- Commercial hot waxes applied by auto­
matic car washes affect the cleanability
of the windshield .
- You can also use the service position, for
example, if you want to protect the
windshield from ic ing by using a cover .
- You cannot activate the service pos it ion
whenthehoodisopen.
Mirrors
Adjusting the exterior mirrors
g 0 :i .., m
Fig. 53 Fo rwa rd section of dr ive r's a rm rest: power mir­
r or co ntr ols
Turn the knob to the desired position :
Q/P -In this position, you can adjust the
d river's and front passenger's exter io r mirrors
by turning the knob in the desired direction.
Qlil -The mirrors are heated depending on the
outside temperature .
8 -The exterior mirrors fold in. In the MM I,
you can se lect if the m irrors fold in automat i­
cally when you lock the vehicle ¢ page
34 .
Tilt function for the passenger 's mi rror
T o help you see the curb when backing into a
parking space, the surface of the mirror tilts Clear vi
sion 55
slight ly. The knob must be in the P position
for t his to happen.
You can adjus t the tilted m irror surface by
turning the knob in the desired direction.
When you move out of reverse and into anoth­
er gear, the new mirror position is stored and
ass igned to the key you are using .
The mirror goes back into its orig inal position
once you drive forwa rd faster than 9 mph (15
km/h) or switch the ignition
off.
A WARNING
-Curved (i .e. convex) mirror surfaces in­
crease your field of view. Remember that
veh icles or other objects will appear
smaller and farther away t han when seen
in a flat m irror. If you use th is m irror to
estimate distances of following veh icles
when changing lanes, you could estimate
incor rectly and cause an accident.
(D Note
-If the m irror housing is moved uninten­
tionally (for example, while parking your
veh icle), then yo u must first fold the mir­
ror electrically. Do not readjust the mir­
ror housing man ually . You cou ld damage
the motor which controls the mirror .
-If you wash the vehicle in an automatic
car wash, you must fold the exterior mir ­
rors in to reduce the risk of damage to
the mirrors . Never fold power fo lding ex­
terior mirrors by hand. On ly fold them in
and out using the power controls.
(D Tips
-The exterior m irror sett ings are stored
with the memory function* ¢ page
66.
-If there is a malfunction in the electrical
system, you can sti ll adjust the exterior
mirrors by pressing the edge of the mir­
ror .

Front passenger's seat
Always move the front passenger seat into the rearmost position .
To avoid contact with the airbag while it is de­
ploying, do not sit any closer to the instru­
ment panel than necessary and always wear
the three-point safety belt provided adjusted correctly . We recommend that you adjust the
passenger's seat in the following manner:
.. Bring the backrest up to an (almost) upright
pos it ion .
Do not ride with the seat reclined .
.. Adjust the head restraint so the upper edge
i s as even as possib le wit h the top of you r
head .
If that is not possib le, try to adjust
the head restraint so that it is as close to
this position as possible ¢
page 65.
.. Place your feet on the floor in front of the
passenger's seat.
Front seats
Controls
Moving the seat forward or back and adjust­
ing the height , backrest angle and seat an­
gle.
F ig . 57 Fron t seat: adju sting th e seat
@ -Mov ing the seat forward/back: press the
button forward/back ¢ .&, .
@ -Mov ing the sea t up/down : p ress the but­
ton up/down ¢& . To ad just the front sect ion
of the seat, press the front button up/down
¢ .&, .To adjust the rear sect ion of the seat,
press the rea r button up/down
c> ,& .
@ -Turn the massage function on/off. You
can select the type of massage using the mu l­
tifunct ion button
c> pag e 60.
Sea ts a nd s to rage 59
© -Backrest forward/back: press the button
forward/back ¢ .&, .
©-Comfort head restraints¢ page 65,
¢ ,& .
(D -Multifunction button ¢,& , ¢page 60.
A WARNING
-Never adjust the driver's or front pas­
senger's seat whi le the vehicle is moving.
If you do th is while the veh icle is moving,
you will be out of position. A lways adjust
the dr iver's or front passenger's seat
when the vehicle is not moving.
- Be ca reful when adj usting the seat
height. Check to see that no one is in the
way, or serious injury cou ld resu lt!
- Because the seats can be electrically ad­
justed with the ignition off, never leave children unattended in the vehicle . Unsu­
pervised use of the electric seat adjust­
ments may cause serious injury.
- To reduce the risk of injury in the case of
sudden braking or accident, front pas­
sengers must never ride in a moving ve­
hicle with the backrest reclined . Safety
be lts and the airbag system on ly offer
maximum protection w hen the backrest
is upr ight and the safety belts are prop­
erly positioned on the body . The more
the backrest is reclined, the greater the risk of persona l injury from an incorrect
seating position and improperly posi­
tioned safety belts.

60 Seats and st o rage
Multifunction button
App lies to vehicles: wit h memory fu nctio n
You can adjust the massage function, upper
section of the backrest, lumbar support, side
bolsters, seating surface and safety belt
height using the multifunction button.
F ig. 58 MMI display : seat settings
Operating
• The M MI displays the possible seat sett ings
@ when yo u turn the mu ltifunction button
page 59, fig. 57 to the left or right
c:> fig. 58, c:> .&_ .
• To select a seat setting, turn the multifunc­
tion button
is h ighlighted with a red border.
• The arrows ® indicate the possible adjust­
ments . For example, to move the lumbar
support down, press the multifunct ion but­
ton
l ights up .
The following seat settings @are possible:
Mas sage funct ion * -Massage type Wave,
K nock in g, Stretch, Lumbar , Shoulder or Off .
You can set the massage strength level from 1
to 5 . You can turn the selected massage on/
off us ing the button ®
c:> page 59, fig. 5 7.
Safe ty belt h eight adju stment * -Moving the
safety belt up/down
c:> page 148, c:> .&..
Upper backre st -Moving the ang le of the up­
per section of the backrest forward/back
c:> &.
Lu mb ar support -Moving the lumbar support
up/down and making it firme r/softer
c:> .&. .
Side bol ster s* -Increasing/reducing the side
support in the seat using the side bolsters on
the seating surface and backrest
c:> &.
Seat ing surfa ce -Making the seat ing s urface
longer/shorter
c:> A .
A WARNING
-
-Never ad just the driver's or front pas­
senger's seat whi le the vehicle is moving.
If you do this while the vehicle is moving,
you will be out of position. A lways adjust
the dr iver's or front passenge r's seat
when the vehicle is not mov ing.
- Be careful when adjusting the seat
he ight . Check to see that no one is in the
way, or serious injury cou ld result!
- Because the seats can be electrically ad­
justed with the ignition off, never leave
children unattended in the veh icle. Unsu­
perv ised use of the e lectr ic sea t adj ust­
men ts may cause serious injury.
- To reduce the risk of injury in the case of
sudden b raking or acc iden t, front pas­
sengers mus t never r ide in a movi ng ve­
hicle with the backrest reclined . Safety
be lts and the airbag system only offer
maximum protection when the backrest
is upright and the safety belts are prop­
erly positioned on the body . The more
the backrest is reclined, the greater the risk of personal injury from an incorrect
seating position and improperly pos i­
tioned safety belts .
@ Tips
-The massage function switches off auto­
matically after approximately 10 mi­
nutes.
- In vehicles w ith the reclining rear seat,
only the safety belt he ight and the seat­
ing surface can be adjusted on the front
passenge r sea t using the mul tifunc tion
butto n.
- T he side bolsters * deflate when t he d riv-
er's doo r is ope ned. This allows you to ..,_

62 Seats and storage
@-Moving the seat forward/back: press the
button forward/back
r=:, .&. .
@ -Moving the seat up/down: press the but­
ton up/down~ &..
©-Switching front passenger seat adjust­
ment on/off: this function must be activated
in the MMI
<=:> page 64 , <=:> &, .To switch front
passenger seat adjustment on, press the but­
ton. You can now adjust the front passenger
seats using the buttons @and @. If you do
not press the buttons ® or@ , front passen­
ger se at adjustment switche s off automatical­
ly after approximately ten seconds.
A WARNING
- The power adjustment for the individual seats also works with the ignition. For
this reason, children should never be left
unattended in the vehicle -they could be
injured!
- Exercise caution when adjusting the
seats . Unsupervised or careless seat ad­
justment can pinch fingers or hands causing injuries.
- Vehicles with a pass through in the cen­
ter console have seating for four. The
Reclining rear seat overview
Applies to vehicles: with reclining rear seat
,-@
_____ ___ ., ------- ---- ·-------- ----- ------
-
Fig. 61 Rear door : ad justing t he reclining po sit ion
CD -Adjusting the reclining position long center console between the two
rear seats is
not a seating position.
Therefore, a safety belt is not provided.
(D Note
If a child seat is attached to one of the rear
seats, this seat must not be adjusted using
the power controls under any circumstan­
ces. The easy entry function for this seat
must also be deactivated in the MMI
<=:> page 64. The child seat as well as the
rear seat can be damaged by the adjust­
ment process.
(D Tips
The massage function switches off auto­
matically after approximately 10 minutes.
- If you cannot move the front passenger
seat, it may be because
- the front passenger's seat memory
function is switched off
r=;, page 67 or
- the child safety lock is switched on (the
@ button ¢ page 41 or the right t
button <=:> page 41 lights up in the driv­
er's door), or
- the front passenger seat adjustment is
switched off in the MMI
r=;, page 64.
@ -Adjusting the standard position

.... N .... N
0 J:
"". .... I.O
"' ....
"' ....
Memory buttons
Applies to vehicles: with memory function
Fig . 66 D rive r's door : mem ory function buttons
Fig. 67 Rear door: mem ory f unction butto ns
The memo ry buttons are located in the dr iv­
er 's/fr ont passenger's door and in the rear
doors* .
Switching the memory function on /off
.. Press the !O FF ! button to switch the memory
function on/off. The LED in t he b utton i llu­
minates when the memory f unct ion is
switched off. Seat ing profiles a re neither
stored nor reca lled.
Storing a seating profile
.. Press the !SE T! butto n. When the word SET
lights up, the memory is ready to store set­
t ings .
.. Press a memory button br iefly. A tone con­
firms that the set tings were stored.
Accessing a seating profile
.. If the driver's door is o pen and t he ignit io n
is switched off, p ress the memory button .
1> Jf the driver's door is closed or the ignition is
switched on, press and hold the memory button until the seat adjustment is com­
plete .
Seats and storage 67
Adjusting the reclining position /standard
position
.. To adjust the reclining position, p ress an d
hold the@ button until the seat moves into
the end posit ion .
.,. To adjust the standard position, p ress a nd
hold t he @ button until the seat moves into
th e end posit ion.
A WARNING
- F or safety re asons, the sea t se tting
should only be rec alled whe n th e veh icle
is station ary -otherw ise you risk hav in g
an accident.
- If n ece ssa ry, you s top t he proc ess by
press ing the
I OFF ! butto n or any o f the
memory buttons .
Adjusting the front passenger seat in
the MMI
Applies to vehicles: with memory function
The driver con adjust the position of the front
passenger seat.
Adjusting the front passenger seat from
the driver's side
.. Select: !CAR ! function button > Car systems
contro l butto n > Vehicle settings > Seats >
Front passenger seat > Adjust seat posi ­
tion .
.,. You ca n now adjust the front passenger seat
using the bu ttons on the driver's seat
~ page 59, fig . 57 .
Matching the position of the driver's seat
.. To adjust the front passenger seat to match
the dr iver's seat settings, select t he
!CARI
fu nction button > Car systems contro l but ­
t on
> Vehicle settings > Seats > Front pas­
senger seat > Symmetry to driver seat .
.,. Press and hold the cont ro l knob unt il the ad-
jus tme nt proces s is co mple te . ..,.

68 Seats and storage
@ Tips
When matching seat settings, the settings
for the lumbar support and seating s ur­
face w ill not transfer to the front
passenger's seat.
Full-length center
console
Overview
A ppl ies to vehicles: with full-le ngth center console
Fig. 6 8 Rear: full-lengt h center conso le
@ -115 volt socket¢ page 68
@ -cupholder ¢ page 74
©-12 volt socket c> page 74
@ -Folding table ¢ page 69
©-center armrest and storage compart­
men ts: to ope n the deep compa rtment, press
the r ight button and fo ld the center armres t
upward . To open the compartment for the
massage function remote control* ¢
page 64
and for the telephone*, press the left button
and fo ld the center armrest upward.
115-volt socket
A ppl ies to vehicles: with 115-volt socket
The 115-vo lt socket can o nly be used when
the eng ine is running ¢,&. . Whe n you push
the connector a ll the way into the socket, the
child safety mechan ism releases and cu rrent
f lows through the socket.
Equipment that can be connected
Elect rical devices can be connected to the 115
volt socket in the veh icle . Power consumption at
the 115-volt socket must not exceed 150
watts (300 watts peak) . Check the power con­
s u mption of the equipment on the mode l
plate.
LED on the socket
- The socket is ready for use when the L ED is
green.
- I f the L ED blin ks red, there is a ma lf u nct ion.
The socket wi ll swi tch off automatica lly due
to overc urrent or overheating . The socket
w ill switch on aga in a utomat ica lly after a
coo l-down period. Any devices that are con­
nected and switched on will activate again
automatically ¢
A.
A WARNING
- The sockets and the electrical accesso ries
connected to them operate only when
the ignition is switched on. Inc orrect us­
a ge can lead to ser ious injur ies or bu rns.
T o reduce the risk of inju ries, never leave
chi ldren unatten ded in the veh icle with
the vehicle key .
- H eavy eq uipment or plugs with in tegrat­
e d power supply units can damage the
socket and lead to injur ies .
- Sto re a ll connected e quipment securely
while the vehicle is moving so that the y
cannot be thrown t hro ugh the veh icle in
the event of a braking maneuver or an
accident.
- Never sp ill any liquids on the socket. I f
any mo isture gets into the socket, make
certain that all the moisture has dried up
before us ing the socket again .
- Equipment that is connected to the vehi­
cle socket can heat up mo re than it does
when connected to the public gr id.
- When us ing adapters and exte ns io n
cords, the child safety for the 115-volt
socket is d isabled and the soc ket is live.
- Never i nse rt anything other than the
p lug of an appropr iate e lectr ical accesso·
ry into th e socket, especia lly t hings that
conduc t electr ic ity, e.g. meta l pens, knit­
t ing nee dles, etc. in to the co ntacts of the
1 15 -volt socket.
~

7 4 Seats and storage
12-volt sockets
Applies to vehicles: 12-volt socke ts
Electrical accessories can be connected to ev­
ery 12-volt socket.
Fig. 78 Section of the trim panel of the luggage com­
partment: 12-volt socket
Fig . 79 Rear center console: 12-volt socket
.. Open the socket cover¢ fig. 78 or¢ fig . 79 .
.. Insert the plug of the electrical device into
the socket .
There is an additional 12 volt socket in the
front center console¢
page 74, fig. 80.
The 12 volt sockets can be used for electrical
accessories. The power input must not exceed
120 watts.
Before you purchase any accessories, always
read and follow the information in
<::> page 292, Additional accessories and parts
replacement.
A WARNING
The sockets and the electrical accessories connected to them operate only when the
ignition is switched on. Incorrect usage
can lead to serious injuries or burns. To re­
duce the risk of injuries, never leave chil- dren
unattended in the vehicle with the
ve­
hicle key.
(D Note
To avoid damaging the socket, only use plugs that fit properly .
-Never connect equipment that generates
electrical current, such as a solar panel
or battery charger, to the 12 volt socket.
This could damage the vehicle's electri­
cal system.
- The 12 volt socket should only be used
for a short period of ti me as a power
source for electrical equipment. Please
use the electrical sockets in the vehicle
when connecting equipment for longer periods.
(D Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle bat­
tery can still be drained .
Storage
'(upholder
Fig. 80 Center console: front cupholder
Fig. 81 Section of the rear bench seat: rear cupholder Ill>