2015 AUDI A8 ignition

42 Opening and closing
Closing the windows
.,. Pull the switch to the first stop and hold it
until the window reaches the desired posi­
tion .
.,. Pull the switch briefly to the
second stop to
automatically close the window.
Power window switches
@ Driver's door
@ Passenger's door
© Left rear door
@ Right rear door
® Safety button (or two safety buttons in
vehicles w ith power child safety locks
r::!) page 41)
Child safety lock
When the safety button®¢ fig. 35 is press­
ed, the LED in the button lights up. The fol­
lowing features are switched off:
- The power windows in the rear doors,
- The buttons for the power sun shades * in
the side windows,
- The buttons for the power sun shade* in the
rear window,
- Front passenger power seat adjustment*
button.
&_ WARNING
- When you leave your veh icle - even if on­
ly brief ly - always take the ignition key
with you. This applies particularly when children remain in the veh icle. Otherwise
the chi ldren could start the engine or op­
erate electrical equipment (e.g. power
w indows). The power windows are func­
tional until the driver's door or passeng­
er's door has been opened .
- Be careful when closing the windows.
C heck to see that no one is in the way, or
serious injury could result!
- When locking the vehicle from outside,
the vehicle must be unoccupied since the
windows can no longer be opened in an
emergency.
(D Tips
- The driver can lower or raise the power
sun shades* in the s ide windows by using
switches © and @.
- After the ignition has been switched
off,
the windows can sti ll be opened or
closed for about 10 minutes. The power
w indows are not switched off until the
dr iver's door or passenger's door has
been opened .
What to do after a malfunction
The one-touch open and close function must
be reactivated if the battery has been discon­
nected .
.,. Pull and hold the power window switch until
the window is fully closed .
.,. Release the sw itch and then pull it again for
at least one second.
Valet parking
The valet parking feature protects the lug­
gage compartment from unauthorized ac­
cess .
Fig. 36 Valet parking button
With "valet parking" activated , the luggage
compartment lid cannot be opened .
.,. Remove the mechanica l key
¢ page 32.
.,. Open the glove compartment and activate
¢ fig. 36 the "valet parking" feature by
pressing the
j VA LETi button . The indicator
light in the sw itch illuminates .
.,. Close the glove compartment and lock it
w ith the mechanical key . .,.

44 Opening and clo sing
Emergency closing of the slid ing /tilting
sunroof
If the sunroof detects an object in its path
when it is closing , it will open again a utomati ­
cally. In this case, you can close the roof with
the power emergency closing function .
.. Within five seconds after the s unroof opens
automatically, pull the switch until the roof
closes .
Panoramic sunroof
Opening/closing the roof
Applies to vehicles: with panoramic sunroof
Fig. 38 Sectio n of th e front headliner : pa noramic s un­
roof b utt on
Fi g. 39 Rear doo r: pa noram ic sunroof bu tton
@ Tilting the fr ont segment of th e roof
.. To tilt the s unroof completely, press the
button up br iefly to the second level~ -
.. To close the sunroof completely, pu ll the
button
l""'I dow n briefly to the second level
~ .&, .
.. To select a tilted position, press/pull the
button
l""'I to the first level unti l the desired
position is reached.
@ Sliding the front segment of the roof
.. To open the sun roof completely, slide the
button
~ back to just befo re the second
level ¢
fig. 38.
.. To close the sunroof comp letely, s lide the
button [;] forward briefly to the second lev ­
el¢.&, .
.. To select a partially open pos ition, slide the
button~ forward/back to the first level un ­
til the desired position is reached .
Tilting the rear segment of the roof
The rear segment of the roof can be operated
both from the cockpit and from the rear seat.
.. To t ilt the sunroof completely , press the
button ~ in the rear door briefly to th e sec­
o nd level ¢
fig. 39 .
.. To close the sunroof completely, pull the
button[;] up briefly to the second level
¢ .&, .
.. To select a tilted pos ition, press/pull the
button~ to the first level unt il the desired
position is reached. O r
.. To operate the roof from the cockpit, p ress
the
I REAR MODE ! button~ fig. 38. You can
now ope n/close the rear segment of the roof
using the button
l""'I in the headliner. The
LED in the front of the headliner turns on
when the rear roof segment is til ted.
After the ignition is switched off, you can still operate the panoramic sunroof for about 10
minutes. The sw itch is deact ivated once the
drive r's or front passenger's door is opened .
A WARNING
--
Be careful when closing the panoram ic
sun roof- otherw ise serio us i njury could re­
su lt! Fo r th is reason, always ta ke the ig ni­
t io n key w it h you whe n leaving the vehicle .
(1) Note
Always close your panoramic s unroof whe n
l eav ing your vehi cle. Sudde n ra in can cause
dam age to the inter io r equipment of your
vehicle, p artic ularly t he e lectronic equip­
ment.

46 Clear vis ion
Clear vision
Lights
Switching the headlights on and off
Fig . 40 Instr ument pane l: lig ht sw itc h w it h all -weath­
er lig hts
The headlights only wo rk when the ignition is
sw itched on. Wh ile start ing the eng ine or
when switching off the ig nition, the head­
lights will go off and on ly the s ide marker
lights w ill be on .
I f the sys tem is not operating properly, a
warn ing symbol in the dr iver information dis­
p lay is displayed <=>page
22 .
Light switch -~ -
Turn the switch <=>fig. 40 to the co rrespond ing
position . When the lights a re switched on , the
:o o: symbo l turns on .
0 -The lights are off or the dayt ime run ning
lights are on:
- US A model s: The daytime running ligh ts
will come on automatically when the igni­
t ion is on and the light switch<=> fig .
40 is in
the
O posit ion or the A UTO position (only in
daylight cond itions) . T he
Daytime running
lights
function can be turned on and off in
the MMI <=> page
47, <=> .& .
-Canada model s: T he daytime running lig hts
will come on automa tically when the igni ­
t ion is on and the light switch<=> fig .
40 is in
the
O posit ion, the :oo~ position or the AUTO
posit ion (on ly in daylight conditions)<=>.& .
AUTO -Automatic headlights swi tch on and
off depend ing o n brightness , fo r example in
twi light, during rain or in tunnels<=>.& .
:oo~ -Side marker lights
io -Low beam head lights
~ -All-weather lights
@!l -Rear fog lights *. When th e rear fog lights
a re on , the symbol
0$ on the sw itch will i llu­
minate .
All-weather light s
In vehicles with all -weather lights, the front
lights are ad justed automatically so that you
are less like ly to see glare from your own
headlig hts, for example when driving on a wet
road .
Automatic dynamic headlight range
control *
Your vehicle is equipped with a headlight
range control sys tem so that the headligh ts
do not blind oncoming traffic if the vehicle
load cha nges . The headlight range a lso ad­
justs automatically when braking and acceler­ at ing .
Light function s
The following ligh t funct ions are available de·
pending on veh icle equipment and o nly fu nc­
t io n when the lig ht switch is i n the AUTO pos i­
t ion . You can deactivate these functions in the
MM I under
Audi adaptive light r:!> page 47 .
Static cornering light *· the cornering light
switches on automatically when the steering
wheel is turned at a certa in angle at speeds
u p to approxima tely 44 mph ( 70 km/h) and
when the t urn sign al is activated at speeds up
to approximately 25 mph (40 km/h) . The area
to the s ide of the vehicle is illuminated better
whe n turning.
Dynamic curv e light * -the curve ligh t only
f unct ions at speeds between approximately 6
mph (10 km/h) and 68 mph ( 110 km/h) and
adapts itse lf to the cu rves in the road.
Highway light function* -this function
adapts the lighting for highway driving based
o n ve hicle speed .
Ill>

48 Clear vision
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu:
Headlights a ctivation time -You can adjust if
the head lights switch on
Early , Med. or Late
according to the sensitivity of the light sensor.
Audi adaptive light* -You can switch adaptive
light
On and Off.
Automatic high beams*
You can switch the high beam assist on and
off .
Daytime running lights
USA models :
You can switch the daytime run ­
ning lights
on and off .
Canada models:
The function cannot be
turned off. It is activated automatica lly each
time the ignition is switched on . This menu
item is shown "greyed out".
Coming home, Leaving home
The coming home function illuminates the
area outside the vehicle when you switch the
ignition off and open the driver's door. To turn
the function on, select
Lights when leaving
car> On.
The leaving home function illuminates the
area outside the vehicle when you un lock the
ve hicle . To turn the funct ion on, select
Lights
when unlocking car > On .
The coming home and leaving home functions
on ly operate when it is dark and the light
switch is in the
AUTO position.
Turn signal and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and
the high beam as well as the headlight flash­
er.
Fig. 42 Tu rn signal and high beam lever
The turn signa l and high beam lever has the
following functions:
Turn signals ¢ 9 (D@
.. Push the lever up as far as it can go to turn
on the right turn signal or down to turn on
t he left turn signal
¢ fig. 42 .
N 0 ... 'i' :r
~
.. Move the lever briefly until you meet res ist·
ance and re lease it to flash three times.
.. Move the lever (up or down) until you meet
resistance and hold it there to determine
the flashing time for the turn signals.
High beam [D @
.. Push the lever forward to switch on the high
beam (vehicles with high beam assist*
¢page49).
.. Pull the lever back towards you to switch off
the high beam .
Headlight flasher [D ©
.. Pull the lever toward the steering wheel to
use the headlight flasher.
Notes on these features
-The turn signals only work w ith the ignition
switched on. The indicator lights
ID or iPJ
in the instrument cluster ¢page 11 also
blink.
- After you have t urned a corner, the turn sig -
na l switches off automatically .
Ill>

50 Clear vis ion
& WARNING
H igh beam assist is only intended to assist
the driver. The driver is still responsible for controlling the headlights and sw itching
th e high beams on and off manually de­
pending on traffic, l ighting and visibility
condi tions. Failure to intervene manually
may lead to ris k of accident . It may be nec­
essary to operate the high beams man ua l­
ly in the following situat ions, e.g .:
- For adverse weather conditions such as
fog, heavy rain, blowing snow or spraying
water .
- On roads where oncoming traffic may be
partia lly obsc ured such as expressways .
-If there are individuals on the road with
no light ing or poor lighting, such as cy ­
cl ists .
- In tight c urves and on steep s lopes .
- In poorly lit areas.
- With strong reflectors su ch as signs.
- If the area of the windshie ld nea r th e
sensor is fogged over, dirty, icy or cov­
ered w ith a st icker.
(D Tips
- The high beam ass ist is active above a
speed of approx . 25 mph (40 km/h).
- If afte r activation, your speed falls below
approx . 15 mp h (24 km/h), the high
beams w ill automatically be switched
off.
Interior lights
Front and rear interior lighting
Fi g. 44 Headliner: Front interior lights
F ig. 45 Rear headli ner : Read ing light
Press the app ropriate button ~ fig . 44:
~ -Inter ior light ing on/off
l!l -Door contact switch. The interior lighting
turns on automatically when you u nlock the
vehicle, open a door or switch the ignition off.
The interior light ing turns off several seconds
after you close the doors, when you lock the
vehicle or when you switch the ignition on.
When a doo r is open, the light turns off after
a few min utes.
~ -Read ing lights on/off
~ - Switching the rear reading lights on/off
from the cockpit .
I REAR MODEi* -Switching the rear readi ng
li ghts on/off from the cockpit : press the
I REAR MODE ! button and then th e appropriate
button ~ in the cockpit.
Ambience lighting
Applies to veh icles: w it h amb ience l ig h ting
You can select a color profile and brightness
for the ambie nce lighting in various areas of
the ve hicle, called zones.
Turning ambience lighting on
.. Select in the MMI: ICAR ! function button >
Car systems control button > Vehicle set·
tings > Interior light ing > On .
Adjusting /turning off the brightness
• Sele ct in the MM I: ICARI fu nction button >
Car sy stems control b utton > V ehicle set­
ting s> Inte rior light ing > Brightness .

.. Turn the knob to the desired vehicle area
and press the knob . The bar that appears in­
dicates the selected brightness .
.. To increase or reduce the brightness, turn
the knob and press it.
S electing a color profile*
.. Se lect in the MMI:
!CAR ! function b utton >
Ca r sys tems control button > Vehi cle se t­
tings
> In terior light ing > Colo r profile .
The amb ience lig hti ng turns on when the
function is activated in the MMI and when you
turn the headlights on whi le the ignition is
switched on.
Adjusting the b rightness
You can ad just the brightness for the four
zones Front top , Fr ont f ootwell , Rear top and
Rear footwell or for All area s at the same
time.
Selecting a color pr ofile
You ca n select from the Ivory, Polar and Ru­
b y/ Polar color profiles .
(I) Tips
The settings are automati cally sto red and
a ssigne d to the remote con tro l key that is
in use.
Instrument illumination
You can adjust the brightness of the instru­
ment and display illumina tion as well as the
Head-up Display*.
F ig. 46 Instrument illum ination
.,. Press the knob to release it.
Clear vi sion 51
.. Turn the knob toward" -" or "+" to reduce or
i ncrease the brightness .
.. Press the knob aga in to return it to its origi­
nal position.
(D Tips
The instrument illumination (for dials and needles) lights on when the ignition is
switched on and the vehicle lights are
turned off. As the daylight fades, t he illu­
mination of the dials li kewise d ims a uto­
matically and w ill go out completely when
the outs ide light is very low. Th is feature is
meant to rem ind you to sw itch on the
headligh ts when ou tside ligh t conditions
b ecome poor .
Vision
Sun visors
Fig. 4 7 Sun visor
E )
-' @
The sun visors for the driver and passenger
can be re leased from their brackets and
turned toward the doors
c> fig. 47@. They
can a lso be moved back and forth lengthwise
in th is position .
The mirror light switches on when the cover
over the vanity m irror @opens.
There is a shade between the dr iver's and pas­
senger's s un v isors that can be used to cover
the gap above the rearview mirror.

52 Clear vision
Sun shade
Fig. 48 Cockp it : Sun shade switc h
Fig. 49 Rear door: S un shade button
Extending/retracting the rear window
shade*
~ To extend or retract the sun shade from the
cockpit,
press the r.t.l button in the center
console
c> fig . 48 .
~ To extend or retract the sun shade from the
rear of the vehicle ,
press the rn button in
the door
c> fig. 49.
Extending the rear door sun shades*
~ Close the window in the rear door.
~ To extend th e sun shade from the driver's
seat,
pull the left/r ight rear power window
switch~ in the driver's door .
~ To extend the sun shade from the rear of
the vehicle,
pull the power window sw itch
11:. in the left/right rear door.
Retracting the rear door sun shades*
~ To retract the sun shade from the driver's
seat ,
press the left/ right rear power window
switch~ in the driver's door .
~ To retract the sun shade from the rear of the
vehicle,
press the power window switch~
i n the left/ right rear door. You
can adjust the settings for the rear sun
shade so the shade retracts automatically
when you select the reverse gear. Select:
CAR
function button > Car systems control button
> Vehicle settings > Automatic rear blind >
On. The settings are automatically stored and
ass igned to the remote control key. The sun
shade extends again as soon as the vehicle be­
gins traveling forward at a speed greater than
9 mph (15 km/h), as long as the ignition has
not been sw itched off in the meantime .
_&. WARNING ~
When lowering or raising the sunshade,
make sure there is nothing in its way and
that it has a free path to travel. This could
cause personal injury.
(D Tips
-
- Pressing the button~ several times
consecutively can trigger the overload
protection. The sun shade can only be ex­
tended/retracted again after a brief wait­
ing period.
- The rear window sun shade only func­
tions when the vehicle interio r is warmer
than
14°F (-10°() .
· Vanity mirror in the rear
Applies to vehicles: with vanity mirrors in the rear
Fig. 50 Rear headliner : vani ty mirro r
~ Press the button to fold the mirror open .
The mirror lighting turns on automatically.
~ To change the mirror's ang le, move it for­
ward/back w ith your hand.

Wiper and washer system
Switching the windshield wipers on
Fig. Sl W indshield wiper leve r
Move the windshield wiper lever to the corre­
spond ing pos ition:
@ -Windshie ld w ipers
off
(D -Rain sensor mode. The w indshie ld w ipers
switch on once the vehicle speed exceeds ap­
proximately 2 mph (4 km/h) and it is raining.
The higher the rain sensor sensitivity is set
(switch @to the right), the earlier the w ind­
shield wipers react to moisture on the wind­
shie ld. You can deact ivate rain sensor mode in
the MMI, which w ill then activate intermittent
mode. Select:
ICARI function button > Car sys­
t e m s
control button > Dri ver ass is t > Ra in
s en sor
> Off . In intermittent mode, you can
adjust the interval time using the switch @.
@ -Slow wiping
@-Fast wiping
©-Single wipe. If you hold the lever in this
position longer, the wipers switch from slow
wiping to fast wip ing .
® -Clean the windshield . The wipers wipe
one time after several seconds of driving to
remove water drop lets. You can switch this
function
off by moving the lever to position ®
within 10 seconds after the afterw ipe . The af­
terw ipe f unction is react ivated the next time
you switch the ig nition on.
Cleaning the headlights . The headlight wash­
er system* only functions when the headlights
are on. If you move the lever to position ®,
Clear vi sion 5 3
the headlights and the night vision system
camera* are washed in intervals.
A WARNING
-The rain sensor is only designed to assist
and support the driver.
It remains entire­
ly the driver's responsibility to monitor
outs ide weather cond itions and to man­
ually activate the wipers as soon as rain
or drizzle reduces visibility through the
windshie ld.
- The windsh ield must not be treated w ith
wate r-repellent mate rials. They can in­
crease glare unde r poo r vis ibility condi­
tions such a s wetness, d arkness, or w hen
the sun is low on the hori zon. In addi ­
tion, they can cause the w indshield wip­
ers to chatter.
- Properly f unctioning windshield wiper
blades are req uired for a clear v iew and
safe driving
¢ page 54, Replacing
windshield wiper blades.
(D Note
- In the case of frost, check whether the
windshield wiper blades are frozen to
the windshield. Switching on the wind­
shield wipers can damage the wiper
blades!
- Prior to us ing a car wash, the w indshield
w iper system must be sw itched off ( lever
in posit ion @). T his he lps to prevent un­
intentional switching on and damage to
the windsh ield wiper system.
- Do not use the wipers to clear a frosted
w indow. Us ing the wipers as a conve n­
ient ice scrape r will destroy the wiper
blades.
(D Tips
- The windshield wipers are sw itched off
when the ign it ion is off . Activate the
w indshield wipe rs after the ignition is
switched back o n by movi ng the w ind­
shield wiper lever to any positi on.
- Worn or d irty wi ndshield wipe r blades
result in streaking. This ca n affec t the