M N
ci LL co
rl I.O
"' N
"' rl
off the ground, placing the Automatic Trans
mission in "P" (Park) will
not prevent the ve
hicle from moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com
partment ¢
page 118 .
(D Note
If you are chang ing the wheel on a steep in
cline, use a rock or sim ilar ob ject to block the
opposite whee l to prevent the vehicle from
mov ing.
(D Tips
Obey a ll laws.
Changing a wheel
When you change o whe el, follow the sequence
described below step-by-step and in exactly that
order.
1. Remove the decorative wheel cover* or the
wheel bolt caps* . For more details see a lso
¢ page 231, Decorative wheel covers or
¢ page 232, Wheels with wheel bolt caps.
2 . Loosen the wheel bolts¢ page 232 .
3. Locate the proper mount ing po int for the
jack and align the jack below that point
¢page 233.
4. Lift the car wit h the jack ¢ page 233.
5. Remove the wheel with the flat tire and then
install the
spare tire¢ page 234.
6. Tighten all wheel bolts light ly .
7.
Lower the vehicle w ith the jack.
8 . Use the wheel bolt wrenc h and
firmly tighten
all wheel bolts in a crisscross pattern
c> page232 .
9. Replace the decorative wheel cover* or the
wheel bolt cap s* .
.&, WARNING
Always read and follow all WARNINGS and in
formation
¢ .&. in Raising the vehicle on
page 233
and ¢ page 235.
Emergen cy assistance
After changing a wheel
A wheel change is not complete without the do
ing the following .
"Always store the vehicle tool kit, the jack", and
the replaced t ire in the luggage compartment
¢page 118.
"Check the tire pressure of the spare tire as soon
as poss ible.
" As soon as possible, have the
tightening tor
ques
on all wheel bolts checked with a torque
w rench. The cor rect tightening torque is 90
ft
lbs. (120 Nm).
" Have the flat tire
replaced as soon as possible.
(D Tips
-If you notice that the wheel bolts are cor
roded and difficult to turn while changing a
tire, they should be replaced before you
check the tightening torque .
- Dr ive at reduced speed until you have the
tightening torques checked.
Decorative wheel covers
Applies to vehicles : wit h decorative w hee l covers
The decorative wheel covers must be removed
first to access the wheel bolts.
Fig . 186 C ha ng in g a w heel: removing the wheel cover
Removing
" Insert the hook provided with the vehicle tool
kit in the hole in the hub .
" Pull off the
decorative wheel cover¢ fig. 186 .
231
M N
ci u.. co ,...., \!) ..,.,
N ..,., ,....,
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right dir ection .
Using a spare tire with a tread pattern
intended for use in a specific direction
When us ing a spa re tire w ith a t read pa tte rn in
t e nded fo r use in a specific d ir e ct ion, p lease no te
the following:
- The direction of rotation is marked by an
arrow
on the side of the tire .
-If the spare t ire has to be installed in the incor
rect direction, use the spare tire only tempora
rily since the tire will not be able to achieve i ts
o ptimum performanc e character istics wit h re
gard to aquaplaning, noise and wea r.
- We recommend that you pay pa rticular atten
t io n t o this fact du ring wet weat he r and t hat
yo u adju st yo ur sp eed to match road condi
t ions.
- Re place the fla t tire w ith a new one and have i t
i nsta lled on yo ur vehicle as s oon as po ssible to
re store the han dling a dvan tages o f a un idirec
t io na l tire.
Notes on wheel changing
P lease read the information ¢ page 216, New
tires or wheels
i f you are going to use a spare tire
which is different from the tires on your ve hicle.
Afte r you change a tire:
- Check the tire pressure on the spare immedi
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as po s
sible by your authorized Audi dealer or quali
fied workshop .
- With steel and alloy wheel rims , the wheel
bolts are correctly tightened at a torque of 90
ft lbs. (120 Nm ).
- If you notice th at the wheel bolt s are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque .
Emergency assistance
-Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi
ble. Remount the wheel cover .
Until then , drive with extra care and at reduced
speed s.
_& WARNING
- If you are going to e quip your ve hicl e wit h
tires o r rims which differ from those which
were factory installed, then be sure to read
the information
¢ page 216, New tires or
wheels.
- Always make sure the damaged wheel o r
even a flat tire a nd the jack a nd too l kit a re
p roperly secu red in the luggage compart
men t and are not loos e in t he passeng er
compa rt m ent.
- In an acci dent or sudde n man euver they
could fly forwa rd, inj uring a nyone in t he ve
h icle.
- Always s to re damag ed wh eel , jack and tools
s ecure ly in the luggage co mpart ment. Ot h
e rwi se, in an accident o r sud den man euver
they co uld fly forward, causing injury to pas
sen gers in t he ve hicle.
(D Note
D o not use co mmercially ava ilab le tire seal
a nts. O therwise, the e le ct ric al c ompone nts of
the tire pre ssure monit oring sys tem * w ill no
l on ger wor k properly and t he sensor for the
tire pressu re monito ring system * wi ll have to
b e replaced by qu alified workshop.
-
235
