2015 AUDI A5 CABRIOLET jack points

M N
ci LL co
rl I.O
"' N
"' rl
Raising the vehicle
The vehicle must be li~ed with the jack first be­
fore the wheel can be removed .
Fig. 189 Sill panels: markings
Fig . 190 Sill: posit ion ing the vehicl e jack
The location of the jack point is indicated by an
indentation on the underside of the vehicle
c::> fig. 189.
;:;; N 0 u. a, ID
.,.. Activate the pa rkin g brake to prevent the vehi­
cle from rolling unintentionally.
.,.. Move the se lector lever to position P .
.,.. Find the
m ar king (imprint) on the si ll that is
nearest the wheel that wi ll be changed
<=> fig . 189. Behind the marking, there is a lift­
ing point on the sill for the vehicle jack .
.,.. Turn the
vehicl e jack located under the lifting
point on the si ll to raise the jack until the jaw
<=> fig. 19O @cove rs the n o tch on the vehicle
Q ,& c::>0.
.,.. Align the vehi cle jack so the jaw @covers the
notch and the base plate @ is f lat on the floor.
The base plate @ must be
vertical under the
lifting point @.
.,.. Install the rod on the veh icle jack: Insert the
rod into the opening on the handwheel. Turn
the rod left or right to secure it.
Em erg en cy ass is tan ce
.,.. Continue raising the jack wit h the rod unt il the
wheel lifts off the ground slightly.
Position t he vehicle jack
only under the designat­
ed lifting points on the si ll
r:1>fig. 189. The re is ex­
actly
one l ocation fo r each wheel. The jack must
not be posit ioned at any other location
c::> .& c::>0 .
Soft ground under the jack can cause the veh icle
to s lip off the jack. A lways place the jack on firm
ground. Use a flat, stable support if necessary.
Use a non-slip surface suc h as a rubber mat on a
slipper y surface such as tile.
_& WARNING
--You or your passengers could be injured
while changing a wheel if you do not follow
these safety precautions:
- Position the vehi cle jack on ly at the desig­
nated lifting points and a lign the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack .
Always provide a firm base for the jack on
the g round. If necessary, use a sturdy
board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipp ing .
- To help prevent injury to yourself and your
passengers:
- Do no t ra ise the vehicle until you are s ure
the jack is secure ly engaged.
- Passengers must not remain in the veh icle
when it is jacked up .
- Make sure tha t passengers wait in a safe
pla ce away from the veh icle and we ll away
from the road and traffic.
- Make sure jack pos ition is cor rect, adjus t
as necessary and then contin ue to raise
the jack .
(D Note
Do not lift the vehicle by the sill. Posi tion the
vehicle j ack only at the des igna ted lifting
233

Emergency assistance
points on the sill. Otherwise, your vehicle will
be damaged.
Taking the wheel off/installing the spare
tire
Follow these instructions step-by-step for chang ­
ing the wheel .
Fig. 191 Cha ngin g a w hee l: u sing t he screwd rive r hand le
(w ith t he blade re moved) to turn the bo lts
Fig. 192 C han gin g a w heel: align men t pin inside the top
h ole
After you have loosened all wheel bolts and
ra ised the veh icle off the ground, remove and re­
p la ce the whee l as follows:
Removing the wheel
"' Remove the topmost wheel bolt completely
with the
hexagonal socket in the screwdriver
handle (vehicle tool kit)
r=;, fig. 191 and set it
aside on a
clean surface.
"' Screw the threaded end of the
alignment pin
from the tool kit hand-tight into the empty bo lt
hole
r=;, fig . 192.
"' Then remove the other wheel bo lts as described
above.
"' Take off the wheel leaving the alignment pin in
the bolt hole
r=;,(I).
234
Putting on the spare tire
"'Push the spare tire over the alignment pin.
"' Screw on the wheel bolts and tighten them
slightly using the hexagona l socket .
"' Remove the alignment pin and insert and tight­
en the remaining wheel bolt slightly like the
rest.
"' Turn the jack hand le counter-clockwise to lower
the vehicle until the jack is fully released .
"' Use the wheel bolt wrench to tighten all wheel
bolts firmly
r=;, page 232. Tighten them in a
crisscross pattern,
from one bolt to the (ap­
proximately) opposite one, to keep the wheel
centered.
"' Perform the steps required after changing the
wheel
r=;, page 231, A~er changing a wheel .
The hexagonal socket makes it easie r to remove
the wheel bolts from the rim. Care should be tak­
en when removing the reversib le blade .
(D Note
When removing or installing the wheel, the
rim could hit the brake rotor and damage the
rotor. Work carefully and have a second per­
son to he lp you.
(D Tips
- When mounting tires with unidirectional
tread design
make sure the tread pattern is
pointed the right way
r=;, page 235.
- The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
- Do not use the hexagonal socket in the
screwdriver handle to loosen or tighten the
wheel bolts.

Emergency situation s
Raising the vehicle
Lifting with workshop hoist and with floor
jack
The v ehicle may only be lifted at the lifting
points illustrated.
F ig . 20 4 Front lift in g po int
F ig . 20 5 Rear l ift ing po int
... Read and heed WARNING c> &_ .
... Locate lifting points c> fig. 204 and c> fig . 205.
... Adjust lift ing arms of workshop hoist or floor
jack to match veh icle lifting points.
... Inse rt a r ubber pad between the floor jack/
workshop hoist and the lifting points .
If you must lift your vehicle with a floor jack to
work underneath, be sure th e vehicle is safely
supported on stands intended for this purpo se.
F ront l ifting point
The lifting point is located on the floor pan rein­
forcement about at the same leve l as the jack
mount ing po int
c> fig . 204 . Do not lift the vehi­
cle at the vertical sill reinforcement .
Rear lift ing point
The lifting point is located on the vertical rein ­
forcement of the lower sill fo r the on board jack
c>fig. 205.
244
Lifting with vehicle jack
Refer to c::> page 233.
A WARNING
- To reduce t he risk of serious injury and vehi­
cle damage .
- Always lift the vehicle only at the specia l
workshop hoist and f loor jack lift points il­
l ustrat ed
c::> fig . 204 and c> fig. 205.
- Failure to lift the veh icle a t these points
could cause the veh icle to tilt o r fall from
a lift if th ere is a cha nge in vehi cle we ight
dis tribu tio n and balance. T his m ight hap­
p en, for example, whe n he avy compone nts
s uch as the en gine block or tran smission
are removed .
- W hen removing he avy componen ts like
these, anchor vehicle to hoist or ad d corre ­
spond ing weights to ma intain the center of
grav ity . Otherwise, the vehicle might ti lt o r
slip off the ho ist , causing se rious persona l
in jury .
(D Note
-Be aware of the following points before lift ­
ing the vehicle:
- The veh icle should never be lifted or
jacked up from underneath the engine oil pan, the transmis sion housing, the front
or rear axle or the body side members .
This could lead to serious damage .
- To avoid damage to the underbody or
chas sis frame , a rubber pad must be in­
serted between the floor ja ck and the lift
points.
- Before driving over a workshop hoist,
check that the vehicle weight doe s not
exceed the permissible lifting capacity of
the hoist.
- Before driving over a work shop hoist , en­
sure that the re is sufficient clearance be­
tween the hoist and low parts of the ve­
h icle.