2015 AUDI A5 CABRIOLET key

M N
ci u.. co ,...., \!) 1.1"1
N 1.1"1 ,....,
At speeds above about 1 mph (2 km/h) the Auto­
matic Shift Lock is automatically deactivated in
the N position.
A time delay element prevents the selector lever
from locking when it is moved through the N po­
sition (going from R to D/S). The locking element
will lock the se lector lever if the lever is left in N
(Neutral) for more than approximate ly 2 seconds,
without the brake pedal being pressed.
Release button
The release button on the selector lever prevents
the lever from being accidentally shifted into cer­
tain positions. Depending on the direction of the
shift, the selector lever locks at different posi­
tions. The positions are highlighted in the illus­
tration
c> fig . 97.
Ignition key safety interlock
The key cannot be removed from the ignition un­
l ess the se lector lever is in the P park posit ion.
When the ignit ion key is removed, the selector
lever will be locked in the P position.
Driving the automatic transmission
Applies to vehicles: with m ultit ron ic/S tronic/t iptronic
F ig . 98 S hift gate on t he center conso le: selector lever w ith
re lease button
Starting the engine
~ The selector lever must be in P or N.
Starting off
~ Press and ho ld the brake pedal.
~ Press and hold the release button in the selec­
tor lever handle, select the des ired selector lev­
er posit ion such as D/S and release the button.
Automatic transmission
~ Wait briefly until the transmission has shifted
(you will fee l a slight movement).
~ Remove your foot from the brake pedal and ac­
celerate.
Stopping temporarily
~ Keep the vehicle stationary using the braking
pedal, for example at traffic lights.
~ Do not press the accelerator peda l when doing
this.
~ To prevent the vehicle from rolling when you
start driving, set the parking brake when stop­
p in g on steep inclines
c> .&_.
~ The parking brake will release automat ically
and the vehicle will start mov ing once you press
t he acce lerator pedal.
Stopping/parking
If the selector lever is not in the P position when
you open the dr iver's door, the vehicle could roll.
The message
Transmission: Car may roll! Shift
to park!
appea rs.
~ Press and hold the brake pedal until the vehicle
has come to a complete stop .
~ Apply the parking brake c:;. page 78, Parking .
~ Select the P selector lever posit ion c> .&_ .
Stopping on an incline
~ Always press the brake pedal to hold the vehi­
cle in place and prevent it from "rolling back"
c:;. .&_ . Do not try to prevent the veh icle from
"rolling back" when a gear is engaged by in­
creasing the engine speed
c> 0 .
Starting on an incline
~ Activate the parking brake.
~ With the driving gear selected, press the accel ­
erator pedal carefully. The parking brake w ill re­
lease automat ically if your seat belt is fastened .
Under certain circumstances, such as driving in
the mounta ins, it may be useful to sw itch tempo­
r ar ily to the manual shift program in order to ad­
just the gears to the dr iv ing conditions by hand
c>page 87.
On slopes, activate the parking brake first and
then move the selector lever to the P position .
85

M N
ci LL co
rl I.O
"' N
"' rl
will no longer shift at a ll. The engine may stall.
Drive to your authorized Audi dealer or qualified
repair facility immediately to have the malfunc ­
tion corrected.
rm l;j Transmission malfunction: No reverse
You can continue driving
S tronic transmission: There is a system malfunc­
tion in the transmission. The transmission is
switching to emergency mode. This mode only
shifts into certain gears or will no longer shift at
all. The engine may stall. You cannot engage the
reverse gear. Drive to your authorized Audi dea ler
or qualified repair facility immediately to have
the ma lfunction corrected .
rm Transmission malfunction: Stop vehicle and
shift to park.
Do not continue driving. Select the P se lector lev­
er position and see your authorized Audi dealer
or qualified repair facility for assistance.
([) Note
If the transmission switches to emergency
mode, you shou ld take the vehicle to an au­
thorized Audi dealersh ip as soon as possible
to have the condit ion corrected.
Selector lever emergency release
Applies to vehicles: with multitronic/5 tronic/tiptronic
If the vehicle's power supply foils, the selector
lever can be released in an emergency.
Fig . 101 Front center console: Removing the ashtray insert
Automatic transmission
Fig. 102 Selector lever emergency release
"'To access the emergency release mechanism,
remove the ashtray insert @ using the release
sw itch @ c:::>fig.
101.
"' Loosen and remove the cap in the ashtray
mount.
"' You now have access to a pin. Using a screwdriv­
er or similar object, press the pin down and
hold it in that position
c:::>fig . 102.
"' Now press the re lease button and move these-
lector lever to the N position .
The selector lever can only be moved from the P
position if the key is in the lock and the ignition is
switched on . If the power supply fails (for exam­
ple, the battery is discharged) and the vehicle
must be pushed or towed, move the selector lev­
er to the N position first using the emergency re­
lease.
89

M N
ci LL co
rl I.O
"' N
"' rl
Audi adapt ive crui se cont rol and bra king gu ard
~ -- -~ -Di sta nce 3: This setting corresponds
to a distance of 164 feet/SO meters when trave l­
ing at 62 mph (100 km/h), or a t ime interval of
1.8 seconds.
~ -- --~ Dista nc e 4: This setting corresponds
to a distance of 210 feet/64 meters when trave l­
ing at 62 mph (100 km/h), or a t ime interval of
2 .3 seconds.
A WARNING
Following other vehicles too closely increases
the risk of collisions and ser ious personal in ­
jury.
- Setting short distances to the traffic ahead
reduces the time and distance available to
br ing your vehicle to a safe stop and makes
it even mo re necessary to pay close atten­
tion to traffic.
- Always obey applicable traffic laws, use
good judgment, and select a safe following
distance for the traffic, road and weather
condit ions.
¢j) Tips
- Di stance
3 is set automatically each time
you switch t he ignition on.
- Your standa rd settings are automatically
stored and assigned to the remote contro l
k ey being used.
Setting the driving program
Applies to vehicles: with Audi adaptive cruise control
D epending on the se lected dr iv ing program and
distance, driving behavior when accelerating will
vary from dynamic to comfortab le .
Setting th e driving program for v ehicl es
without Audi d rive s elect*
~ In the radio/MMI*, select: !CAR !function but­
ton >
Adapti ve c ru is e control > D riv ing prog. >
comfo rt, stand ard or d y namic . Or
~ Select : !CAR I function button> Ca r sy ste m s*
co ntrol button > D river ass ist > Adap tive cru ise
cont ro l
> Dr iving progr am * > Comfort, Stand­
ard
or D ynamic . Setting the driving mode for vehicles w
ith
Audi dri ve select*
Refer to ¢ page 104.
(D Tips
Your settings are automatical ly stored and as ­
signed to the remote control key being used.
Request for driver intervention
Applies to vehicles: with Audi adaptive cruise control
Fig . 1 12 Instr ume nt cluster: reques t fo r dr ive r inte rven ­
t ion
In certa in situations, the system will prompt you
to ta ke act ion. This cou ld happen, fo r example , if
braking by the adaptive c ruise control system is
not enough to maintain enough distance to the
vehicle ahead.
T he instrument cluster w ill warn you abou t the
dange r
~fig. 112:
-A red vehicle is p ictured in the display .
- The text
DISTANCE! appears in the status bar .
- The red indicator light . blinks .
- In addition, a warning tone sounds .
95

M N
ci u.. co ,...., \!) 1.1"1
N 1.1"1 ,....,
Audi adaptive cruise control and braking guard
promptly detected or may not be detected
at all.
- Reflective surfaces including crash barriers
or tunnel entrances may impair the function
of the radar sensor.
(D Tips
- You can cancel the braking that is initiated by the system by braking yourself, by accel­
erating noticeably or by swerving.
- Braking guard error messages
Q page 97.
- Keep in mind that braking guard can brake
unexpectedly. Always secure any cargo or
objects that you are transporting to reduce
the risk of damage or injury.
Settings in the radio /MMI
App lies to vehicles: with Audi adaptive cruise co ntrol
... Select : I CARI function button > Car systems*
control button > Driver assist> Audi braking
guard .
Or
... Select :
~I C-A-R~I function button > Audi braking
guard.
System -
Switch Audi braking guard On and Off.
When you switch the ignition on, the message
Audi braking guard off appears if the system is
switched off.
Early warning -The distance and approach warn ­
ings in the display can be switched
On/Off.
(D Tips
-Your settings are automatically stored and
assigned to the remote control key being
used at the times the settings are made.
- If you restrict or switch off the ESC, the
braking guard also switches itself off
¢ page 171.
- Switch braking guard off when you are load­
ing the vehicle onto a vehicle carrier, train,
ship or other type of transportation . This
can prevent undesired warnings from the
braking guard system.
Messages
Applies to vehicles: wi th Aud i adap tive c ruise control
Braking guard: Off
This driver message appears if the system is
turned off via the radio/MMI*. Otherwise, if the
system is turned off, the information appears ev­
ery time shortly after the start of the trip.
The driver message also appears if the system is
not available due to a malfunction or if the ESC is
not switched on
¢ page 171. If this is the case,
the system will not provide warnings about a possible collision.
Braking guard: Activated
This driver message appears if sharp brake pres­
sure was applied due to an acute warning .
•••
Three white dots appear if a setting cannot be se­
lected with the operating lever. For example, this
happens if you want to raise/lower the speed
even though there was no previously saved
speed .
ACC: Sensor blocked
This message appears if the sensor view is ob­
structed, for example by leaves, snow, heavy
spray or dirt. Clean the sensor~
page 90,
fig. 103.
ACC: not available
The driver message appears if there is a malfunc­
tion. The adaptive cruise control turns off. A
chime sounds as a reminder. Have the system
checked by an authorized Audi dealer or author­
ized Audi Service Facility.
ACC: unavailable
The driver message appears if, for example, the
brake temperature is too high. The adaptive
cruise control is temporarily unavailable . A chime
sounds as a reminder.
Shift lever position!
The driver message appears if the selector lever
is shifted to the N position. The adaptive cruise
control is not available while in this position. .,..
97

Audi side assist
(D Tips
-Side assist is not active while you are mak­
ing the adjustment.
- Your settings are automatically stored and
assigned to the remote control key being
used.
Driver messages
Applies to veh icles: w ith Aud i side ass ist
If side assist switches off by itself, the LED in the
button turns
off and a message will appear in the
instrument cluster display:
Audi side assist unavailable: Sensors blocked
The radar sensors' vision is affected. Do not cover
the area in front of the sensors with bike wheels,
stickers, dirt or other objects. Clean the area in
front of the sensors, if necessary ¢
page 100,
fig. 117.
Audi side assist: Currently unavailable
Side assist cannot be switched on temporarily be­
cause there is a malfunction (for example, the
battery charge level may be too low).
Audi side assist: System fault!
The system cannot guarantee that it will detect
vehicles correctly and it is switched off . The sen­
sors have been displaced or are faulty. Have the
system checked by an authorized Audi dealer or
authorized Audi Service Facility soon.
Audi side assist: Unavailable when towing
Side assist switches off automatically when a fac­
tory-installed trailer hitch is connected to the
electrical connector on the trailer. There is no
guarantee the system will switch off when using
a retrofitted trailer hitch. Do not use side assist
when towing a trailer.
102

M N
ci u.. co ,...., \!) 1.1'1
N 1.1'1 ,....,
Systems Comfort
Adapti ve dampers *
comfortable
Sport differenti al* ba la nced
Adaptive cruise control * comfortable
Engin e sound * subtle
al Subt le in the dri ving pos itio n D and spo rty i n th e d rivin g pos ition S .
(D Tips
Your Individual* mode se ttings are au tom ati­
cally stored and assigne d to the remote con­
trol key being used.
Audi drive select
Auto Dynamic
balanced sporty
agi le sporty
balanced sporty
su bt le/ sportya)
sp orty
105

M N
ci LL co
rl I.O
"' N
"' rl
,&_ WARNING
-Sensors have dead spaces in which objects
cannot be detected . Be especially alert for
small chi ldren and animals, since they are
not always detected by the sensors .
- The acoustic parking system is not a substi­
tute for the dr iver's own caution and alert­
ness. Ultimate responsibility always remains
with the driver during parking and sim ilar
maneuvers . A lways watch where you are
dr iv ing .
- You should always adjust the volume and
frequency of the warning tones so that you
can eas ily hear the acoustic distance warn­
ing
even if the radio is playing, the air-cond i­
tioner blower is on High or there is a high
level of outs ide no ise.
- Check the settings whenever anyone else
has driven the vehicle be fore you.
(D Note
- Remember that low obstacles for whic h a
warning has already been issued may "dive"
below the system 's sensing zone if the vehi­
cle is being backed up closer . In this case,
the warn ing sound shutting off does
not in­
dicate that you have cleared the obstacle.
Instead, impact is imm inent.
- Objects such as trailer h itches, cha ins, nar ­
row posts or fences covered by a thin layer
of pa int may not a lways be detected by the
system. They can still damage your vehicle
wi thou t warn ing.
{O) Tips
Keep the sensors in the rear bumper clean
and free of snow and ice so that the acoust ic
parking assist system can f unction properly.
Adjusting the warning tones
Applies to vehicles: with parking system (rear)
The warning tones can be adjusted in the MMI*.
• Select : ICARI function button > Parking system.
Or
• Se lect :
I C ARI funct ion button > Car syste m s*
control button> Dr iver a ssist> Parking aid .
Parking Sy stem
- Rear volum e -rear sensor vo lume
- Rea r fre quenc y -rear sensor frequency
- Mu sic vo lume while parking -when the park-
ing system is switched on, the vo lume of the
active audio source is lowered.
The newly adjusted value is briefly hea rd from
the signal generator . T he settings are automat i­
ca lly stored and assigned to the master key w ith
remote control.
Rear parking system
with rearview camera
Introduction
Applies to vehicles: with parking system (rear, with rear view
camera)
F ig . 1 21 Park ing mode 1: reve rse pa rking
Fig . 1 22 Park ing mode 2: parallel parking
Vehicles with the parking system are equipped
with a
rear vi ew ca mera in addi tion to the acous­
t ic pa rking system.
You can choose between two modes to ass ist you
with pa rking. For example, you can use "parking
mode l" when park ing in a parking sp ace or ga­
rage ¢
fig. 121. When you wan t to park parallel
to the edge of the street, select "park ing mode
2" ¢ fig. 122 . 11>
107

Parkin g Sys tem
sw ings out more than the vehicle rear . Main ­
tain plenty of distance from an obstacle so
that your outside mirror or a corner of your
veh icle does not collide w ith any obstacles -
danger of accident!
(D Tips
The left or right orientation lines and surfaces
w ill be displayed, depending on the turn sig­
nal being used.
Adjusting the display and warning tones
Applies to vehicles: w ith parking system (rear, with rear view
camera)
The display and warning tones ore adjusted in
the radio or MMI*.
.. Se lect: ICARlfunct ion button> Parking sy stem .
Or
.. Se lect: ICAR I function button> Car system s*
control button > D riv er a ss is t> Par king aid .
D isplay
- Off -when the pa rking system is switched on,
o nl y aud ible signals are given.
- On -when the pa rking system is switched on,
the p icture from the rear view camera is dis­
played.
Warning tones
- Rea r volume -
rear sensor volume
-Rear frequenc y -rear sensor frequency
- Music volume wh ile pa rking -when the pa rk-
ing system is switched on, the volume of the
active aud io source is lowered .
The newly adjusted value is briefly heard from
the signal generator. The settings are automati­
cally stored and assigned to the remote control key .
A WARNING
- Always make sure that the volume and fre ­
quency of the wa rning tones is adj usted so
that you can eas ily hear the acoust ic dis­
tan ce signal even if the radio is p laying, the
air-con ditione r blower is on High or t here is
a high level of outside noise .
112
-Check the settings whenever someone else
has dr iven the vehicle before you .
@ Tips
-The warn ing tones can also be adjusted di ­
rectly from the rear view camera image.
Simply press the Settings * cont ro l button .
- Changed settings are activated when park ­
ing assist is switched on again.
Error messages
Applies to vehicles: with parking system (rear, with rear view
camera)
If a warning tone is aud ible for about five sec­
onds when you turn on the ignition, there is a malfunction in the system. Have the problem cor ­
rected by your author ized Audi dealer .
Keep the sensors in the rea r bumper clean and
free from ice so that the aco ustic park assist sys ­
tem can function properly .