
76 Driving
Driving
Steering
Adjusting the steering wheel position
The steering wheel position is fully adjustable
up and down and forward and bock .
Fig. 78 Steering column: stee ring column adjustmen t
lever
.. Tilt the lever ¢ fig. 78 downward ¢ &_.
.. Bring the steering wheel into the desired
position .
.. Push the lever against the steering column
until it latches .
_& WARNING
Incorrect use of the steer ing whee l adjust
ment and an incorrect seating position can
cause serious injuries.
- Only adjust the steering column when
the vehicle is stationary so that you do
not Lose control of the vehicle.
- Adjust the driver's seat or steering wheel
so that there is at least 10 inches
(25 cm) distance between your chest and
the steering wheel
r=.> page 12 7,
fig. 123. If you do not maintain this dis
tance, the airbag system will not be able
to provide its full protection
<=> page 127, fig. 123.
- If your physical characteristics prevent
you from sitting at least 10 inches
(25 cm) or more away from the steering
wheel, see if your authorized Audi dealer or authorized Audi Service Fac ility can
provide adapters that will help.
- If your face is level with the steering
wheel, the airbag does not provide as much protection during a collision. Al
ways make sure that the steering wheel
is level with your chest .
- Always hold the steering wheel with your
hands in the 9 o'clock and 3 o'clock posi
tions to reduce the risk of injury if the
airbag deploys.
- Never hold the steering wheel in the 12
o'clock position or with both hands on
the rim or the center of the steering
wheel. Holding the steering wheel incor
rectly significantly increases the r isk of
injury to the hands, arms and head if the
airbag deploys.
Starting and stopping
the engine (vehicles
with an ignition lock)
Starting the engine with the key
Applies to vehicles: wit h mechanical ignition loc k
The ignition is switched on and the engine
started with the key in the ignition.
Fig. 79 Ignit ion key positions
Steering lock
If the steering wheel will not turn, the steer
ing lock is engaged.
To engage the steering wheel Lock: The selec
tor lever must be in the P position.
"' To engage the steering wheel lock, turn the
wheel until it locks when the ignition key is
removed .
"' To release the steering wheel Lock, insert
the key in the ignition lock and turn the key
in the -direction of the arrow-whi le turning
the steering wheel. ""

M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
"'T o sw itch the ignition on, turn the ignition
key to position
(D .
"'To switch the ignition off, turn the ignition
key to position @.
Starting the engin e
Your vehicle is equipped w ith launch cont ro l.
As soon as you have turned the ign ition key to
position @, the engine will start automatical
l y.
"' Press the brake peda l and move the se lector
lever to the P or N pos it ion.
"'T urn the key briefly to position @. The igni
t ion key automatically r eturns to posit ion
(D . Do not press the accelerator pedal wh en
doing this .
Major electrical equipment switches off tem
porarily when starting the eng ine.
If the engine does not sta rt immedia tely , stop
the starting procedure by turning the ignition key to position @and repeat after 30 sec
onds .
Automatic start m alfunction
If the ~ indicator l ight turns on (gasoline en
g ine) and the message
Engin e start sys te m
m alfu nction. Ple ase contac t Se rvice
appears ,
there is an automatic start ma lfunction.
To start t he eng ine, hold the ignition key in
position @until the engine runs .
Drive to an authorized Aud i dealer or author
ized Audi Service Facility immed iate ly to have
the ma lfunction corrected .
_& WARNING
-Never allow the engine to run in confined
spaces -there is a risk o f asphyxiation.
- Never remove the ign ition key from the
ignition lock whi le the vehicle is moving .
Otherw ise the steering lock wi ll engage
and you will not be able to steer the vehi
cle.
- Please note that the brake booster and
power steering only work when the en-
Dri vin g 77
gine is running. When the engine off, you
must use more force to steer or brake
the vehicle. Because the usual steering
and brak ing capability is not avai lab le,
the risk of accidents or injur ies increases.
- Always take the vehicle key with you
when leaving the vehicle, even for a
short period of time. This applies part ic
ularly when children remain in the veh i
cle. Otherwise the ch ild ren could start
the engine or operate electrical equip
men t such as power w indows.
(D Note
- Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has no t reached operat ing tempera
t u re yet . You could damage the engine.
- T he engine cannot be started by pushi ng
or towing.
(® For the sake of the environment
Do not let the eng ine run w hile pa rked to
warm u p. Begin driv ing immediately . T his
r educes unne cessary emissions.
(D Tips
- If it is d iff icult to turn the key to position
(D , turn the steering wheel back and
forth slightly to release the s teer ing
wheel lock .
- After s tarting a cold engine, there may
be a brief period of inc reased no ise be
cause the oil press ure must first bui ld up
in the hydraulic va lve adj usters . This is
normal and not a cause for concern.
- If the battery is disconnected and recon
nected, you have to hold the ignition key
in posit ion
(D for five seconds for the en
gine to start.
- After sw itching the ignition off, you can
only remove the key when the selector
lever is in the "P" (Park) position. After
that, the selector lever is locked.
•

M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
If the> ,:r- u indicator l ight blinks and the mes
sage
Ple ase move s teering wheel appea rs
when switching the ignition on, the steering is locked by th e steering lock. In this case, turn
the steering wheel slight ly to the left/ right.
.. To switch the ignition on or
off, press the
I S TAR T ENG INE S T OPI button. Do not press
the brake pedal whil e doing this .
Starting the engin e
Your vehicle is equipped with launch cont ro l.
The engine starts automa tically when you
press the
I S T AR T ENG INE S T OP I button brief
l y.
.. Press the brake peda l and move the se lector
lever to the P or N pos ition .
.. Press the
I STAR T ENGINE STOP I button
briefly . The eng ine will star t.
Majo r electrical equ ipment switches
off tem
porarily when starting the eng ine .
I f the engine does not start immediately , stop
the starting procedu re by push ing the
I S TAR T ENGINE ST OP ! button again and re
peat after 30 seconds .
Automatic start m alfunction
If the Ila indicator l ight turns on (gasoline en
g ine) when you start the engine, there is an
automatic sta rt malfunction .
To start the eng ine, press and hold the
!STAR T ENGIN E STOP ! button until the eng ine
runs.
Drive to an authorized Aud i dealer or author
i z ed Audi Service Fac ility immed iately to have
the malfunction corrected .
A WARNING
-Never allow the engine to ru n in confined
spaces -there is a r isk of asphyxiation.
- Always take the veh icle key with you
when leaving the vehicle, even for a
short per iod of t ime . This applies partic
ularly when chi ldren remain in the vehi
cle . Otherwise the children could start
Dri vin g 79
the engine or operate electrical equip
ment such as power w indows.
- Please note that the brake booster and
power steering only work when the en
gine is running. When the engine
off, you
must use more force to steer or brake
the vehicle . Because the usual steer ing
and brak ing capability is not avai lable,
the risk of accidents or injur ies increases .
(D Note
-Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has not reached operat ing tempera
ture yet. You could damage the engine .
- The engine cannot be started by pushing
or towing .
@ For the sake of the environment
Do not let the eng ine run wh ile parked to
warm up . Begin dr iv ing immediately . Th is
reduces unnecessary emissions .
(D Tips
-After starting a cold engine, there may
be a brief period of increased no ise be
cause the oil press ure must f irst bu ild up
in the hydraulic va lve ad justers. This is
normal and not a cause for concern.
- If the . indicator light blinks in the in
st rument cluste r before switching the ig
nition
off, the ignit ion wi ll not switch on
again .
qpoge 192
- If you leave your vehi cle wit h the ignition
switched on, the ign it ion w ill switch
off
after a certain amount of time . Make
sure that electrical equipment such as
the exterior lights are switched
off .
T · th · ff using the
button
App lies to vehicles: wit h convenience key
.. Bring the veh icle to a full stop .
.. Move the se lector lever into the P posit ion .
.. Press the
I STA RT E NGINE ST OP ! button
q page 78, fig. 80. ..,.
•

M N
" > co ,...., \!) ..,.,
,...., ..,., ,....,
~ Press the brake pedal¢ A in Starting the
engine with the
S TAR T ENGINE STOP but
ton on page 79.
~ Press the l ~ s =T ~A~R=T~E~N-G~I~N~E~s=T~O~P~I button .
~ Hold the maste r key as shown in the illustra
t ion in the location indicated
y>l) ¢ fig . 81 .
The eng ine will start .
~ If the engine does not automatically start,
press the
I STAR T E NGINE STOP! button
again.
Drive to an authorized Aud i dea ler or author
i zed Audi Service Fac ility immed iate ly to have
the ma lfunction co rrected .
(D Tips
You can disp lay the message that appears
during an eme rgency by p ressing the
!S TART EN GINE STOPI* button.
Driver messages
Turn off ig nition befor e leaving car . Batter y
is disc har ging
This message appears and a warn ing tone
sounds if yo u ope n the dr ive r's door when the
i gnit ion is switched on. Sw itch the ignition off
so that the batte ry wi ll not discharge.
Pr ess ing start/stop button again will sw it ch
off engin e!
This message appears when you press the
I STAR T ENGIN E STOP !* button while dr iv ing
¢ page 80, Emergency off function.
E ngine start s ystem malfunction. Please
contact Service
The engine automatic start system has a mal
function. Drive to an authorized Audi dealer or
author iz ed Audi Serv ice Facility immediately
to have the ma lfunction corrected . To start
t he eng ine, press and hold the
I STAR T ENGIN E STOP ! button .
DJ Key not recognized . See owne r's manual
This message appea rs i f the re is no conven
ience key inside the vehicle or if the system
does not recognize the key. The convenience key may not be recognized, for examp le, if it is
Dri vin g 81
cove red by an object that disrupts the s ignal
(such as a briefcase), or if the key battery is
weak. E lectronic devices such as ce ll phones
can a lso interfere with the signa l.
T o still be ab le to start or stop the engine, re
fer to "Correcting a malfunction"¢
page 80.
Ill Key not in vehi cle?
The Ill in dicator light turns on and th is mes
sage appears if the co nvenience key was re
moved from the vehicle when the engi ne was
run ning . If the convenience key is no longer in
the ve hicl e, you cannot switch the igni tion on
o r start the engine once yo u stop it . You also
cannot lock the vehicle from the outside .
Press brake pedal
Th is message appears if you do not p ress the
brake pedal when sta rting the eng ine .
Please eng age N or P
This message appears when starting or stop
ping the engine if the se lector l ever is not in
the N or P position. The engine will not start/
stop.
Shift to P , othe rwi se vehicle can roll away.
Door s do not lock if le ver is not in P
T h is mess age appears for safety reasons
along wi th a warn ing tone.
It appea rs if the
selector lever for the automatic transm ission
is not in the P pos it ion when switching the ig
nition off with the
I S TAR T ENGINE STOP !*
button. Shift the se lec tor lever to the P posi
tion . Otherw ise, the vehicle could roll . You al
so cannot lock the vehicle us ing the loc king
senso r o n the door hand le or using the con
venience key.
•

82 Driving
Electromechanical
parking brake
Operating
The electromechanical parking brake replaces
the hand brake.
Fig. 82 Ce nter conso le: Park ing brake
~ Pull the switch@~ fig. 82 to set the park
ing brake . The . (USA models)/ . (Cana
da models) indicator lights in the button
and in the instrument cluster display turn
on .
~ To release the parking brake, press the brake
or acce le rator pedal while the ignit ion is
switched on and press the button @at the
same time. The. (USA models)
I. (Can
ada models) indicator lights in the button
and in the display turn off .
Your veh icle is eq uipped with an electrome
chanical parking brake. The parking brake is
designed to prevent the vehicle from rolling unintentionally and replaces the hand brake.
I n addition to the normal functions of a tradi
tional hand brake, the electromechanical parking brake provides various convenience
and safety functions.
When starting from a stop
- T he integral hill start assist helps you when
dr iving by automatically releasing the park
ing brake ~
page 83, Starting from a
stop .
-When starting on inclines, the hill start as
sist prevents the vehicle from unintentional
l y rolling back. The braking force of the
parking brake is not released until sufficient driving force has been built up at the
wheels.
Emergency brake function
An emergency braking functions ensu res that
the vehicle can be slowed down even if the
normal brakes fail~ page 84, Emergency
braking function.
_.&. WARNING
- Do not press the accelerator pedal inad
vertently when the vehicle is stationary
and the engine is running and a gear is
selected. Otherwise the vehicle will start
to move immediately and could result in
a crash .
- If the power supply fails, the released
parking brake can no longer engage . In
this case, park the vehicle on leve l
g round and secure it by placing these
lecto r lever in the P position. See an au
thorized Audi dealer or authorized Audi
Service Facility for assistance.
(D Note
If the. or. (USA models) I. (Cana
da models) indicator light in the instru
ment cluster blinks, there is a malfunction
i n the brake system. Refer to the detai led
description of the indicator lights
~page 18.
- If the . (USA models) I. (Cana-
da models) or
Ill indicator light turns
on, there is a malfunction in the parking
brake
c> page 19.
(D Tips
- If the electromechanica l parking brake is
set while the ignition is switched off, the
¢@'A indicator light in the button and in
the instrument cluster dis-
play . (USA models) /. (Cana-
da models) will turn off after a certain
amount of time.
- If driver's door is opened while the igni
tion is switched on, the park ing brake
sets automatically. This prevents unin
tended rolling of the vehicle.

M N
" > co ,...., \!) ..,.,
,...., ..,., ,....,
-Occasiona l noises when the parking
brake is set and re leased are norma l and
are not a ca use for concern .
- When the vehicle is parked, the parking
brake goes through a se lf-test cycle at
regular intervals. Any noises associated
with th is are normal.
- If there is a power failure, the parking
brake will not set if it is released, and it
will not release if it is set c::>
,&. See an
authorized Audi dea ler or authorized
Audi Service Facility for assistance .
Parking
"'Press the bra ke peda l to stop the vehicle.
"' Pull the switch@c::>
page 82, fig. 82 to set
t h e parking bra ke.
"' Place the selector lever in the P position .
"'T urn the eng ine
off c::> _& .
"'Turn the steering whee l when parking on in
clines so that the whee ls will ro ll into the
curb if the vehicle starts moving.
A WARNING
-Always take the vehicle key with you when leaving the veh icle, even for a
short per iod of t ime. This applies partic
u larly when ch ild ren remain in the vehi
cl e. Otherwise chi ld ren could sta rt the
engine, re lease the par king brake or op
erate electrical eq uipment such as powe r
w indows, which increases the risk of an
acc ident.
- No one sho uld remain in the vehicle
when it is locked, especia lly children.
Locked doors make it more diffic ult for
emergency workers to get into the vehi
cle, which puts lives at risk.
Dri vin g 83
Starting from a stop
The start assist function ensures that the
parking brake is released automatically upon starting .
Stopping and setting the parking brake
"' Pull the sw itch @c::> page 82 , fig. 82 to set
the parking brake.
Sta rting and automatically rel easi ng the
parking brake
Req uirement: The dr iver's door must be
locked and the driver's safety belt must be
fastened.
"' When you press the accelerator peda l, the
parking brake is automatically re leased and
your vehicle begins to move.
When stopping at a traffic signal or stopping in city traff ic, the parking brake can be ap
plied . The vehicle does not have to be held
with the brake pedal. The parking brake elimi nates the tendency to creep when a selector
lever pos it io n is engaged. As soon as you
press the accelerato r peda l, the par king b rake
r eleases a utomat ica lly and the vehicle starts
to move.
Starting on slopes
When sta rting on incl ines, the hill start assist
prevents the vehicle from un intent ionally roll
i ng ba ck. The bra kin g fo rce of the par kin g
brake is not re leased unt il su ff ic ient d riving
f o rce has been built up a t the wheels.
(D Tips
Fo r safety reaso ns, t he pa rking bra ke is re
l eased automatic ally o nly when the d riv
er's safety bel t is fa stened an d the driver's
d oor is locked.
•

88 Audi adaptive cruise control
- When approaching stationary objects
such as stopped traff ic, adaptive cruise
control will not respond and pre sense
front will have limited function.
- The adaptive cruise control system and
pre sense front do not react to people,
animals, objects cross ing the road or on
coming objects.
- The function of the radar sensors can be
affected by reflective objects such as
guard rai ls, the entrance to a tunnel,
heavy rain or ice.
- Never follow a veh icle so closely that you
cannot stop your vehicle safe ly. The
adaptive cruise control cannot slow or
brake the vehicle safely when you follow
another vehicle too closely. Always re
member that the automatic braking
function ca nnot bring the veh icle to a
sudden or emergency stop under these
condit ions.
- To prevent unintended operation, always
switch ACC off when it is not be ing used.
(D Note
The sensor can be disp laced by impacts o r
damage to the bumper, whee l housing and
underbody . The adaptive cruise contro l
and pre sense front may become impaired
as a result . Have an authorized Audi dealer
or author ized Audi Service Facility check
their function.
In curves
Applies to vehicles: with Audi adaptive cruise control and
Audi pre sense fro nt
Fig. 85 Examp le: driv ing into a curve
When driving into a curve c::> fig. 85 and out of
a curve, the adaptive cruise control may react
to an object in the neighboring lane and apply
the brakes. You can prevent that by pressing
the accelerator pedal briefly .
Stationary objects
Applies to vehicles: with Audi adaptive cruise contro l and
Audi pre sense front
Fig. 86 Example: object chang ing lanes a nd stationary
object
Adaptive crui se control
The adaptive cruis e control system only reacts
to objects that are moving or that the system has a lready detected as moving. For examp le,
if a detected vehicle @tur ns or changes
lanes, the adaptive cruise control will not re
act to a stopped vehicle @. Press the brake
pedal to slow your vehicle down .
Pre sense front
Pre sense front only reacts to stationary ob
jects at low speeds.
Adaptive cruise control
Description
Applies to vehicles: with Audi adaptive cruise control
--~.....,
~~ 'l! !/.~~!!iii
Fig. 87 Detectio n ran ge

....,
N
r--. > co
rl I.O
"' rl
"' rl
Setting the driving program
Applies to vehicles: with Audi adaptive cruise control
A adaptive cruise con trol dr iving program is
adjustable on vehicles witho ut Audi dr ive se
l ect* .
• Select in the MMI: the
I MENU I button > Car
> Systems * control button > Driver assis
tance > Adaptive cruise control> Driving
program > Comfort/Standard/Dynamic.
Selecting the driving mode
Applies to vehicles: with Audi adaptive cruise co ntrol
The adaptive cruise contro l driving program is
ad justab le for veh icles w ith Audi drive se lect
using the driving mode.
• Select the desired driving mode
Comfort,
Auto , Dynamic or Individual *
with the knob
Qpage 107 .
Request for driver intervention
Applies to vehicles: with Audi adaptive cruise co ntrol
Fig. 93 Inst rumen t cluster: dr iver inte rve ntion reques t
In some s ituations, the braking from the
adaptive cruise control system is not enough
to maintain enough distance to the object
ahead . In these s ituations, the system will re
quest you to take action .
The . indicator light and the graphic in the
display wi ll wa rn yo u about the danger
Q fig. 93. You will a lso hear an aud io signa l.
Press the brake pedal to s low your vehicle
down.
Audi adaptive cruise control 93
Driver messages
Applies to vehicles: wit h Aud i adapt ive c ru ise control
IIJ ACC: unavailable
The system cannot guarantee that it will de
tect objects correctly and is switched off. The
sensor was moved or is faulty. Drive to your
authorized Aud i dea ler or a uthorized Audi
service facility immediately to have the mal
function corrected.
fl ACC: currently unavailable. No sensor vi
sion
fl ACC and Audi pre sense: currently un·
available. No sensor vision No sensor visio n
This message appears if the sensor v iew is ob
structed, for example by leaves, snow, heavy
spray or dirt. Clean the sensor
Q page 87,
fig. 84.
Ill ACC: currently unavailable . Gradient too
steep
The road exceeds the maximum possible an
gle for safe adaptive cruise control operat ion.
The adaptive cru ise control cannot be switch
ed on.
Ill ACC: only available in D, Sor M
Select the D/S or M selector lever position.
Ill ACC: parking brake applied
The adaptive cru ise control system switches
off automatically if the parking b rake is set .
The adaptive cruise control is available again
after re leas ing the parking brake.
Ill ACC : currently unavailable . Stabilization
control input
This message appears if the Electronic Stabili
zation Control (ESC) is taking action to stab i
lize the veh icle . In this case, adapt ive cru ise
control switches off automat ica lly.
Ill ACC off: manual control!
This message appears if the vehicle rolls back
when starting on a s light incline, even though
ACC is active. Press the brake pedal to prevent
the vehicle from rolling or starting to move.
1111-