2014 VOLVO V60 lock

||
10 Maintenance and service
10
354
1. Plug in the connector, a clicking soundshould be heard.
2. Reinstall the headlamp and locking pins. The short pin is fitted closest to the grille. Check that they are correctly inserted.
3. Check the lighting. The headlamp must be mounted and the con- nector correctly installed before the lighting isswitched on or the remote control key isinserted into the ignition switch.
Related information
• Lamp replacement (p. 352)
• Lamp replacement - cover for main/ dipped beam bulbs (p. 354)
• Lamps - specifications (p. 358)
Lamp replacement - cover for main/ dipped beam bulbs
Main/dipped beam bulbs are accessed by releasing the headlamp's larger cover.
Before starting to replace a bulb, see Lamp replacement - headlamps (p. 353).
1. Unscrew the cover's four screws using a
Torx tool, size T20 (1). They should not be loosened completely. (3 - 4 turns are suf-ficient.)
2. Slide the cover to one side.
3. Remove the cover.Reinstall the cover in reverse order.
Related information
• Lamp replacement - headlamps (p. 353)
• Lamp replacement - dipped beam (p. 355) •
Lamp replacement - main beam (p. 355)
• Lamp replacement - extra main beam (p.355)
ProCarManuals.co’

10 Maintenance and service
10
* Option/accessory, for more information, see Introduction.355
Lamp replacement - dipped beam
The dipped beam bulb is fitted inside the headlamp's larger cover.
NOTE
Applies to cars with halogen headlamps.
1. Detach the headlamp (p. 353).
2. Remove the cover (p. 354).
3. Unplug the connector from the bulb.
4. Detach the bulb by pulling it straight out.
5. The guide pin on the lamp should be
straight up when it is fitted and a clicking sound should be heard when it clicks intoplace.
Reinstall the parts in reverse order.
Related information
• Lamps - specifications (p. 358)
Lamp replacement - main beam
The main beam bulb is fitted inside the head- lamp's larger cover.
NOTE
Applies to cars with halogen headlamps.
1. Detach the headlamp (p. 353).
2. Remove the cover (p. 354).
3. Detach the bulb by turning anticlockwise
and then pulling straight out.
4. Unplug the connector from the bulb.
5. Replace the bulb and align it in the socket and turn clockwise in order to secure it. It can be secured in one position.
Reinstall the parts in reverse order.
Related information
• Lamps - specifications (p. 358)
Lamp replacement - extra main beam
The extra main beam bulb is fitted inside the headlamp's larger cover.
NOTE
Applies to cars with Xenon headlamps*.
1. Detach the headlamp (p. 353).
2. Remove the cover (p. 354).
3. Detach the bulb by turning anticlockwise
and then pulling straight out.
4. Unplug the connector from the bulb.
5. Replace the bulb and align it in the socket and turn clockwise in order to secure it. It can only be secured in one position.
Reinstall the parts in reverse order.
Related information
• Lamps - specifications (p. 358)
ProCarManuals.co’

10 Maintenance and service
10
356
Lamp replacement - direction indicators front
The direction indicator lamp is fitted inside the headlamp's smaller cover.
1. Detach the headlamp (p. 353).
2. Detach the cover by pulling it straight out.
3. Pull the bulb holder in order to extract thebulb.
4. Press and simultaneously turn the bulb to detach it.
Reinstall the parts in reverse order.
Related information
• Lamps - specifications (p. 358)
Lamp replacement - rear lamp
Rear direction indicators, rear fog lamp and reversing lamp are replaced from inside thecargo area.
Lamp housing, rear
The bulbs for reversing lamp, fog lamp and direction indicator in the rear lamp cluster arereplaced from inside the cargo area.
1. Open the panel.
2. Remove the insulation that is fitted in
front of the bulb holder by pulling it straight out.
3. Press down the catch and pull out the bulb holder.
4. Remove the blown bulb by pressing it in and turning anticlockwise.
5. Fit a new bulb, press down and turn clockwise. 6. Press down the catch when the bulb
holder is refitted.
7. Refit the insulation and panel.
Related information
• Lamp replacement - location of rear lamps (p. 357)
• Lamps - specifications (p. 358)
ProCarManuals.co’

10 Maintenance and service
10
359
LightingWAType
–––
Reversing lamp21P21W LL
Rear fog lamp21H21W LL
A
Watt
Related information
• Lamp replacement (p. 352)
• Lamp replacement - location of rear lamps (p. 357)
• Lamp replacement - vanity mirror lighting(p. 358)
Wiper blades
The wiper blades sweep water away from the windscreen and rear window. Together withthe washer fluid they clean the windows andensure visibility for driving. The windscreen wiper blades must be in serv- ice position when they are to be replaced.
Service position
Wiper blades in service position.
In order to make replacement possible, to clean or lift the wiper blades (for scraping office from the windscreen, for example), theymust be in service position.
IMPORTANT
Before placing the wiper blades in the service position, make sure that they arenot frozen down.
1. Place the remote control key in the igni- tion lock 11
and briefly press the START/
STOP ENGINE button to set the car's
electrical system to key position I. For
detailed information on key positions, see Key positions - functions at different lev-els (p. 70).
2. Briefly press the START/STOP ENGINE
button again to set the car’s electricalsystem in key position 0.
3. Within 3 seconds, move the right stalk switch up and hold it in position forapprox. 1 second.
> The wipers then move to standingstraight up.
The wipers return to their starting position when you briefly press the START/STOP
ENGINE button to set the car’s electrical sys-
tem to key position I (or when the car is
started).
11 Not necessary in cars with Keyless function.
ProCarManuals.co’

10 Maintenance and service
10
361
1. Fold out the wiper arm.
2. Grip the inner section of the blade (by the arrow).
3. Turn anticlockwise to use the blade's end position against the wiper arm as a lever to detach the blade more easily.
4. Press the new wiper blade into position. Check that it is firmly installed.
5. Lower the wiper arm.
CleaningFor cleaning wiper blades and windscreen,see Car washing (p. 379).
IMPORTANT
Check the blades regularly. Neglected maintenance shortens the service life ofthe wiper blades.
Related information
• Washer fluid - filling (p. 361)
Washer fluid - filling
Washer fluid is used for cleaning the head- lamps and windows. Washer fluid with anti-freeze must be used during winter.
The windscreen and headlamp washers share a common reservoir.
IMPORTANT
Use washer fluid with antifreeze during the winter to avoid freezing in the pump, reser-voir and hoses.
For capacities, see Washer fluid - quality and volume (p. 401).
Related information
•Wiper blades (p. 359)
Battery
The service life and function of the battery is influenced by factors such as the number ofstarts, discharging, driving style, driving con-ditions, climatic conditions etc. The starter battery is a traditional 12 V bat- tery.
• Never disconnect the battery when the engine is running.
• Check that the cables to the battery arecorrectly connected and properly tight-ened.
WARNING
•The battery can generate oxyhydrogen gas, which is highly explosive. A sparkcan be formed if a jump lead is con-nected incorrectly, and this can beenough for the battery to explode.
• The battery contains sulphuric acid,which can cause serious burns.
• If sulphuric acid comes into contactwith eyes, skin or clothing, flush withlarge quantities of water. If acidsplashes into the eyes - seek medicalattention immediately.
IMPORTANT
Only a traditional battery charger should ever be used when charging the battery.
ProCarManuals.co’

10 Maintenance and service
10
374* Option/accessory, for more information, see Introduction.
Fuses - in the control module under the glovebox
Fuses in the control module under the glove- box protect airbag and collision warning sys-tem functions, amongst other things.
Positions
FunctionA
Rear window wiper15
––
Interior lighting; Driver's door control panel, power windows;Remote controlled garage dooropener*; Power seats, front*7,5
FunctionA
Combined instrument panel5
Adaptive cruise control, ACC*; collision warning system*10
Interior lighting; Rain sensor7,5
Steering wheel module7,5
Central locking system, fuel filler flap10
FunctionA
Heated steering wheel*15
Heated windscreen*15
Unlocking, tailgate10
Folding head restraint*10
Fuel pump20
ProCarManuals.co’

10 Maintenance and service
10
* Option/accessory, for more information, see Introduction.375
FunctionA
Movement detector alarm*; Cli- mate panel5
Steering lock15
Siren*; Data link connector OBDII5
––
Airbags10
Collision warning*5
Accelerator pedal sensor; Dim- ming interior rearview mirror*;Seat heating, rear* Electric additional heater*7,5
Infotainment control module (Performance); Audio (Perform-ance)15
Brake lights5
Sunroof*20
Immobiliser5
Related information
• Fuses - in engine compartment (p. 368)
• Fuses - under glovebox (p. 372)
• Fuses - in cargo area (p. 376) •
Fuses - in the engine compartment's cold zone (p. 377)
ProCarManuals.co’

10 Maintenance and service
10
}}
379
Car washing
The car should be washed as soon as it becomes dirty. Wash the car in a car washwith oil separator. Use car shampoo.
Washing by hand
•Remove bird droppings from the paint- work as soon as possible. Bird droppingscontain chemicals that affect and discol-our paintwork very quickly. An authorisedVolvo workshop is recommended for theremoval of any discoloration.
• Hose down the underbody.
• Rinse the entire car until the dissolved dirthas been removed so as to reduce therisk of scratches from washing. Do notspray directly onto the locks.
• If necessary, use cold degreasing agenton very dirty surfaces. Note that in thiscase, the surfaces must not be hot fromthe sun!
• Wash using a sponge, car shampoo andplenty of lukewarm water.
• Clean the wiper blades with a lukewarmsoap solution or car shampoo.
• Dry the car using a clean, soft chamois ora water scraper. If you avoid allowingdrops of water to dry in strong sunlight,you reduce the risk of water drying stainswhich may need to be polished out.
WARNING
Always have the engine cleaned by a workshop. There is a risk of fire if theengine is hot.
IMPORTANT
Dirty headlamps have impaired functional- ity. Clean them regularly, when refuellingfor example. Do not use any corrosive cleaning agents but use water and a non-scratchingsponge instead.
NOTE
Outside lighting such as headlamps, fog lamps and rear lamps may temporarilyhave condensation on the inside of thelens. This is normal, all exterior lighting isdesigned to withstand this. Condensationis normally vented out of the lamp housingwhen the lamp has been switched on for atime.
Wiper bladesAsphalt, dust and salt residue on wiper blades, as well as insects, ice etc. on thewindscreen, impair the service life of wiperblades. For cleaning:- Set the wiper blades to the service position, see Wiper blades (p. 359).
NOTE
Wash the wiper blades and windscreen regularly with lukewarm soap solution orcar shampoo. Do not use any strong sol-vents.
Automatic car washesAn automatic car wash is a simple and quick way of washing the car, but it cannot reacheverywhere. Handwashing the car is recom-mended for achieving optimum results.
NOTE
The car must only be washed by hand over the first few months. This is becausethe paint is more delicate when it is new.
High-pressure washingWhen using high-pressure washing, use sweeping movements and make sure that thenozzle does not come closer than 30 cm tothe surface of the car (the distance applies toall exterior parts). Do not spray directly ontothe locks.
ProCarManuals.co’