2014 TOYOTA LAND CRUISER Navigation Manual

305
1. AIR CONDITIONING SYSTEM OPERATION
6
AIR CONDITIONING
L/C200_Navi_OM60L27U_(U)
13.06.03 19:43
Front center outlets
Front side outletsRear center outlets
ADJUSTING THE POSITION OF
AND OPENING AND CLOSING
THE AIR OUTLETS
No.Function
Direct air flow to the left or right, up
or down
Turn the knob to open or close the
vent
No.Function
Direct air flow to the left or right, up
or down
Turn the knob to open or close the
vent
No.Function
Direct air flow to the left or right, up
or down
Turn the knob to open or close the
vent

306
1. AIR CONDITIONING SYSTEM OPERATION
L/C200_Navi_OM60L27U_(U)
13.06.03 19:43
1Press the micro dust and pollen filter
button.
Usually the system will turn off automati-
cally after approximately 3 minutes.
MICRO DUST AND POLLEN
FILTER
Outside air mode switches to recircu-
lated air mode. Pollen is removed from
the air that flows to the upper part of
the body.
To stop the operation, press the micro
dust and pollen filter button again.
INFORMATION
●In order to prevent the windows from
fogging up when the outside air is cold,
the following may occur:
• Outside air mode does not switch to
recirculated air mode.
• The air conditioning system operates
automatically.
• The operation cancels after 1 minute.
●In rainy weather, the windows may fog
up. Press the windshield air flow button.
AIR CONDITIONING SYSTEM
OPERATING HINTS
INFORMATION
●Using the automatic mode
• Fan speed is adjusted automatically in
accordance with the temperature set-
ting and ambient conditions. As a
result, the following may occur:
• Immediately after “AUTO” is
pressed, the fan may stop for a while
until warm or cool air is ready to flow.
• Cool air may flow to the area around
the upper body when the heater is
on.
●Using the system in recirculated air
mode
• The windows will fog up more easily if
the recirculated air mode is used for an
extended period.
●Switching between outside air and recir-
culated air modes
• Recirculated air mode or outside air
mode may be automatically switched
in accordance with the temperature
setting and the inside temperature.
●When the outside temperature exceeds
75F (24C) and the air conditioning sys-
tem is on
• In order to reduce the air conditioning
power consumption, the air condition-
ing system may switch to recirculated
air mode automatically. This may also
reduce fuel consumption.
• Recirculated air mode is selected as a
default mode when the “ENGINE
START STOP” switch is turned to
IGNITION ON mode.
• It is possible to switch to outside air
mode at any time by pressing the air
intake control button.

307
1. AIR CONDITIONING SYSTEM OPERATION
6
AIR CONDITIONING
L/C200_Navi_OM60L27U_(U)
13.06.03 19:43
INFORMATION
●Window defogger feature
• Recirculated air mode may automati-
cally switch to outside air mode in situ-
ations where the windows need to be
defogged.
●When driving on dusty roads
• Close all windows. If dust thrown up by
the vehicle is still drawn into the vehi-
cle after closing the windows, it is rec-
ommended that the air intake mode be
set to outside air mode and the fan
speed to any setting except off.
●When outside temperature approaches
32F (0C)
• The air conditioning system may not
operate even when “A/C” is touched.
●Air conditioning filter
• The air conditioning filter may clog
after long use. The filter may need to
be replaced if the air flow of the air
conditioner and heater experiences
extreme reductions in operating effi-
ciency, or if the windows become to fog
up easily. (For details, refer to the
“Owner’s Manual”.)
●Customization
• Settings can be changed.
(For details, refer to the “Owner’s Man-
ual”.)

308
1. AIR CONDITIONING SYSTEM OPERATION
L/C200_Navi_OM60L27U_(U)
13.06.03 19:43
4. REAR AUTOMATIC AIR CONDITIONING SYSTEM
1Touch the rear air conditioning control
button.
2Touch the desired button.
 Left-hand rear seat
Right-hand rear seat
The air conditioning system switches
between individual and simultaneous
modes each time “4-ZONE” is touched.
REAR AIR CONDITIONING
CONTROLS
Adjusting the rear air conditioning tem-
perature and fan speed.
No.Function
Touch “” on “TEMP” to increase
the temperature and “” to de-
crease the temperature.
Touch “” on to increase the fan
speed and “” to decrease the fan
speed. (7 levels)

7
309
1
2
3
4
5
6
7
8
L/C200_Navi_OM60L27U_(U)
13.02.20 14:56
9
10
1. VOICE COMMAND SYSTEM ...... 310
STEERING SWITCHES
FOR THE VOICE COMMAND
SYSTEM ............................................ 310
VOICE COMMAND SYSTEM
OPERATION ..................................... 310
2. NATURAL SPEECH
INFORMATION
(ENGLISH ONLY) ..................... 316
3. EXPANDED VOICE
COMMANDS ............................. 318
4. COMMAND LIST ......................... 319
1VOICE COMMAND SYSTEM
OPERATION
VOICE COMMAND SYSTEM

310
L/C200_Navi_OM60L27U_(U)
13.06.03 19:43
1. VOICE COMMAND SYSTEM OPERATION
1. VOICE COMMAND SYSTEM
Talk switch
Press the talk switch to start the voice
command system.
To cancel voice recognition, press and
hold the talk switch.
1Press the talk switch.
After the “Shortcut Menu” screen has
been displayed, voice guidance will com-
mence.
2After a beep sounds, say the command
of your choice.
Voice commands are marked with .
Some commonly used commands are dis-
played on the screen.
By saying “Next page” or “Previous
page”, or by touching “Next Pg.”/“Prev.
Pg.”, the screen will display the com-
mands displayed on the page in the back-
ground.
Saying “Main menu” or touching “Main
Menu” when the “Shortcut Menu” screen
is displayed will display the “Main Menu”
screen.
Registered POIs, registered names in the
phonebook etc., can be said in the place
of the “<>” next to the commands. (See
page 319.)
For example: Say “Find nearby dining”,
“Call John” etc.
The voice command system enables
the navigation, audio/video, hands-
free and air conditioning systems to be
operated using voice commands.
The operating procedures of voice
commands from the “Shortcut Menu”
screen are explained here.
INFORMATION
●Commands that are not displayed in the
“Shortcut Menu” screen can be operated
from the “Main Menu” screen.
STEERING SWITCHES FOR
THE VOICE COMMAND
SYSTEM
Type A
Type B
VOICE COMMAND SYSTEM
OPERATION
Voice guidance for the voice command
system can be skipped by pressing the
talk switch.

311
1. VOICE COMMAND SYSTEM OPERATION
7
VOICE COMMAND SYSTEM
L/C200_Navi_OM60L27U_(U)
13.06.03 19:43
3Say the command displayed on the
screen.
If a desired outcome is not shown, or if no
selections are available, perform one of
the following to return to the previous
screen:
•Say “Go back”.
• Touch “Go Back”.
To cancel voice recognition, touch “Can-
cel”, or press and hold the talk switch.
Saying “Help” prompts voice guidance
to offer examples of commands and
operation methods.INFORMATION
●If the navigation system does not
respond or the confirmation screen does
not disappear, press the talk switch and
try again.
●If a voice command cannot be recog-
nized within 6 seconds, voice guidance
will say “Pardon?” (“Command not rec-
ognized.” will be displayed on the
screen) and voice command reception
will restart.
●If a voice command cannot be recog-
nized 2 consecutive times, the voice
command guidance system will say
“Paused. To restart voice recognition,
push the talk switch. To cancel voice
recognition, push and hold the talk
switch.” Then voice recognition will be
suspended.
●The voice recognition prompt can be set
to on or off when “Voice Prompts” is
touched. This setting can also be
changed on the “Voice Settings” screen.
(See page 54.)
●When “Voice Prompts” is touched,
voice recognition will be temporarily sus-
pended. Press the talk switch again.
●Voice guidance can be canceled by set-
ting voice prompts to off. Use this setting
when it is desirable to say a command
immediately after pressing the talk
switch and hearing a beep.

312
1. VOICE COMMAND SYSTEM OPERATION
L/C200_Navi_OM60L27U_(U)
13.06.03 19:43
1Press the talk switch.
2Say “Go home”.
A confirmation screen will be displayed
showing the recognition results.
3Say “Yes” or touch “Yes”.
The system starts searching for a route to
your home.
When the voice command is recognized,
the map of the area around the home
address will be displayed and route guid-
ance to the home address will begin.
MICROPHONE
It is unnecessary to speak directly into
the microphone when giving a com-
mand.
INFORMATION
●Wait for the confirmation beep before
speaking a command.
●Voice commands may not be recognized
if:
• Spoken too quickly.
• Spoken at a low or high volume.
• The roof or windows are open.
• Passengers are talking while voice
commands are spoken.
• The air conditioning speed is set high.
• The air conditioning vents are turned
towards the microphone.
●In the following conditions, the system
may not recognize the command prop-
erly and using voice commands may not
be possible:
• The command is incorrect or unclear.
Note that certain words, accents or
speech patterns may be difficult for the
system to recognize.
• There is excessive background noise,
such as wind noise.
VOICE COMMAND EXAMPLE:
SEARCHING FOR A ROUTE TO
YOUR HOME
If a home address is not registered,
voice guidance will say “Your home is
not set. Please try again after setting a
home location.” and you will be
prompted to enter a home address.
(See page 99.)