2014 TOYOTA DYNA 100/150 oil viscosity

GAUGES, METERS AND SERVICE REMINDER INDICATORS71
ENGINE OIL CHANGE REMINDER LIGHT
This light comes on when the engine
switch is turned to the “ON” position. It
goes out after about 3 seconds. This indi-
cates that the system is functioning nor-
mally. If the light illuminates for 3 seconds
and then flashes for about 12 seconds,
this indicates that the time to change the
engine oil is approaching.
If this light stays on this warns you to
change the engine oil and oil filter us-
ing appropriate replacements at your
earliest convenience. For more informa-
tion about oil grade and viscosity, see
“Checking the engine oil level” on page
188 in Section 7−2.
After changing the engine oil and oil filter,
be sure to reset the system, so that the
light goes out. (For instructions on reset-
ting the system, see “RESETTING THE
SYSTEM” on page 72 in this Section.)
The system must also be reset if an en-
gine oil and oil filter change is performed
before the light comes on. If you do not
reset the system, it cannot inform you of
the correct time to change the engine oil
and oil filter.If any of the following occurs, the
system may not be functioning normal-
ly. Have the vehicle checked at any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional.
DWhen the engine switch is turned to
the “ON” position, the light does not
come on.
DThe light flashes.
DAfter changing the engine oil and oil
filter, even though thesystem hasbeen
reset, the light does not go out, or
comes on again soon.
NOTICE
After changing the engine oil and oil
filter, be sure to reset the system.
(For instructions on resetting the sys-
tem, see “RESETTING THE SYSTEM”
on page 72 in this Section.) If you do
not reset the system, it cannot inform
you of the correct time to change the
engine oil and oil filter.
Dyna100/150_EE

INFORMATION BEFORE DRIVING YOUR TOYOTA11 5
FUNCTIONS OF ENGINE OIL
Engine oil has the primary functions of
lubricating and cooling the inside of the
engine, and plays a major role in main-
taining the engine in proper working order.
ENGINE OIL CONSUMPTION
It is normal that an engine should con-
sume some engine oil during normal
engine operation. The causes of oil
consumption in a normal engine are as
follows.
DOil is used to lubricate pistons, piston
rings and cylinders. A thin film of oil
is left on the cylinder wall when a pis-
ton moves downwards in the cylinder.
High negative pressure generated when
the vehicle is decelerating sucks some
of this oil into the combustion chamber.
This oil as well as some part of the oil
film left on the cylinder wall is burned
by the high temperature combustion
gases during the combustion process.
DOil is also used to lubricate the stems
of the intake valves. Some of this oil
is sucked into the combustion chamber
together with the intake air and is
burned along with the fuel. High tem-
perature exhaust gases also burn the
oil used to lubricate the exhaust valve
stems.
The amount of engine oil consumed de-
pends on the viscosity of the oil, the
quality of the oil and the conditions the
vehicle is driven under.
More oil is consumed by high−speed driv-
ing and frequent acceleration and decel-
eration.
A new engine consumes more oil, since
its pistons, piston rings and cylinder walls
have not become conditioned.
Oil consumption:Max. 1.0 L per 1000
km (1.1 qt./600 miles, 0.9 Imp. qt./600
miles)When judging the amount of oil con-
sumption, note that the oil may become
diluted and make it difficult to judge
the true level accurately.
As an example, if a vehicle is used for
repeated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km (600 miles) or more. This
is because the oil is gradually becoming
diluted with fuel or moisture, making it
appear that the oil level has not changed.
The diluting ingredients evaporate out
when the vehicle is then driven at high
speeds, as on an expressway, making it
appear that oil is excessively consumed
after driving at high speeds.
IMPORTANCE OF ENGINE OIL LEVEL
CHECK
One of the most important points in prop-
er vehicle maintenance is to keep the en-
gine oil at the optimum level so that oil
function will not be impaired. Therefore, it
is essential that the oil level be checked
regularly. Toyota recommends that the oil
level be checked every time you refuel
the vehicle.
NOTICE
Failure to check the oil level regularly
could lead to serious engine trouble
due to insufficient oil.
For detailed information on oil level check,
see “Checking the engine oil level” on
page 188 in Section 7−2.
Dyna100/150_EE
Facts about engine oil
consumption

STARTING AND DRIVING129
When encountering flooded roads
Do not drive on a road that has flooded
after heavy rain etc. Doing so may cause
serious damage to the vehicle.
NOTICE
Driving on a flooded road may cause
the engine to stall as well as cause
serious vehicle malfunctions such as
shorts in electrical components and
engine damage from water immersion.
In the event that you drive on a
flooded road and the vehicle is
flooded, be sure to have any autho-
rized Toyota dealer or repairer, or
another duly qualified and equipped
professional check brake function,
changes in quantity and quality of oil
and fluid used for the engine, trans-
mission, differential, etc. and lubricant
condition for the propeller shaft, bear-
ings and suspension joints (where
possible) and the function of all joints
and bearings.
Make sure your coolant is properly pro-
tected against freezing.
Only use “Toyota Super Long Life Coolant”
or similar high quality ethylene glycol
based non−silicate, non−amine, non−nitrite,
and non−borate coolant with long−life
hybrid organic acid technology. (Coolant
with long−life hybrid organic acid
technology is a combination of low
phosphates and organic acids.)
See “Checking the engine coolant level”
on page 190 in Section 7−2 for details of
coolant type selection.
“Toyota Super Long Life Coolant” is a mix-
ture of 50% coolant and 50% deionized
water. This coolant provides protection
down to about−35_C(−31_F).
NOTICE
Do not use plain water alone.
Check the condition of the battery and
cables.
Cold temperatures reduce the capacity of
any battery, so it must be in top shape
to provide enough power for winter start-
ing. Section 7−3 tells you how to visually
inspect the battery. Any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, will be
pleased to check the level of charge.
Make sure the engine oil viscosity is
suitable for the cold weather.
See page 188 in Section 7−2forrecom-
mended viscosity. Leaving a heavy sum-
mer oil in your vehicle during winter
months may cause harder starting. If you
are not sure about which oil to use, call
any authorized Toyota dealer or repairer,
or another duly qualified and equipped
professional—who will be pleased to help.
Dyna100/150_EE
Winter driving tips

DO−IT−YOURSELF MAINTENANCE: Engine and Chassis189
ENGINE OIL SELECTION
“Toyota Genuine Motor Oil” is used in
your Toyota vehicle. Toyota recommends
the use of approved “Toyota Genuine
Motor Oil”. Another motor oil of matching
quality can also be used.
Oil grade:
ACEA C2
NOTICE
Using engine oil other than ACEA C2
may damage the catalytic converter.
Recommended viscosity (SAE):
Temperature range anticipated before
next oil change
Preferred
SAE 0W−30 is filled into your Toyota
vehicle at manufacturing, and the best
choice for good fuel economy and good
starting in cold weather.Oil viscosity (0W−30 is explained here as
an example):
The0Win0W−30 indicates the character-
istic of the oil which allows cold startabil-
ity. Oils with a lower value before the W
allow for easier starting of the engine in
cold weather.
The30in0W−30 indicates the viscosity
characteristic of the oil when the oil is at
high temperature. An oil with a higher vis-
cosity (one with a higher value) may be
better suited if the vehicle is operated at
high speeds, or under extreme load condi-
tions.
Dyna100/150_EE

216SPECIFICATIONS
ENGINE
Valve clearance (engine cold), mm (in.):
Intake 0.20—0.30 (0.008—0.012)
Exhaust 0.35—0.45 (0.014—0.018)
ENGINE LUBRICATION
Oil capacity (drain andrefill—reference

),
L (qt., Imp. qt.):
With filter 7.0 (7.4, 6.2)
Without filter 6.8 (7.2, 6.0)

: The engine oil capacity is a reference
quantity to be used when exchanging.
Warm up and turn off the engine, wait
more than 5 minutes, and check the oil
level on the dipstick.
“Toyota Genuine Motor Oil” is used in
your Toyota vehicle. Toyota recommends
the use of approved “Toyota Genuine
Motor Oil”. Another motor oil of matching
quality can also be used.
Oil grade:
ACEA C2
NOTICE
Using engine oil other than ACEA C2
may damage the catalytic converter.
Recommended viscosity (SAE):
Temperature range anticipated before
next oil change
Preferred
Please contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, for further
details.
COOLING SYSTEM
Total capacity, L (qt., Imp. qt.):
With front and rear heaters
11.5 (12.2, 10.1)
With front heater 10.7 (11.3, 9.4)
Coolant type:
Your Toyota vehicle is filled with “Toyota
Super Long Life Coolant” at the factory.
In order to avoid technical problems,
only use “Toyota Super Long Life
Coolant” or similar high quality ethylene
glycol based non−silicate, non−amine,
non−nitrite, and non−borate coolant with
long−life hybrid organic acid technology.
(Coolant with long−life hybrid organic
acid technology is a combination of low
phosphates and organic acids.)
Do not use plain water alone.
Please contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, for fur-
ther details.
BATTERY
Specific gravity reading at 20_C(68_F):
1.250—1.290 Fully charged
1.160—1.200 Half charged
1.060—1.100 Discharged
Charging rates:
Quick charge 15 A max.
Slow charge 5 A max.
CLUTCH
Pedal free play, mm (in.):
5—18 (0.2—0.7)
Fluid type:
SAE J1703 or FMVSS No.116 DOT 3
Dyna100/150_EE
Service specifications

SPECIFICATIONS217
MANUAL TRANSMISSION
Oil capacity, L (qt., Imp. qt.):
Dyna 100

2.6 (2.7, 2.3)
Dyna 150
2.4 (2.5, 2.1)
Oil type:
Gear oil API GL−4orGL−5
Recommended oil viscosity:
SAE 75W−90

: See “Model code” on page vi in the
beginning of this manual if you are not
sure of your vehicle model.
DIFFERENTIAL
Oil capacity, L (qt., Imp. qt.):
Dyna 100

2.30 (2.43, 2.02)
Dyna 150
3.45 (3.65, 3.04)
Your Toyota vehicle is filled with “Toyota
Genuine Differential Gear Oil” at the
factory. Toyota recommends the use of
approved “Toyota Genuine Motor Oil”.
Another motor oil of matching quality can
also be used.
Oil type:
Standard differential
Hypoid gear oil API GL−5
Limited slip differential
Hypoid gear oil LSD API GL−5
Recommended oil viscosity:
Above−18_C(0_F)
SAE 90
Below−18_C(0_F)
SAE 80W or 80W−90

: See “Model code” on page vi in the
beginning of this manual if you are not
sure of your vehicle model.
Please contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, for further
details.CHASSIS LUBRICATION
Wheel bearings:
Lithium base wheel bearing grease,
NLGI No.2
Ball joints:
Molybdenum−disulfide lithium base chas-
sis grease, NLGI No.1 or No.2
Propeller shafts:
Lithium base chassis grease, NLGI No.2
BRAKES
Minimum pedal clearance when depressed
with the force of 490 N (50 kgf, 110 lbf)
with the engine running, mm (in.):
Dyna 100

59 (2.3)
Dyna 150
51 (2.0)
Pedal free play, mm (in.):
1—6 (0.04—0.24)
Parking brake adjustment when pulled with
the force of 245 N (25 kgf, 55 lbf):
Dyna 100

4—6 clicks
Dyna 150
6—8 clicks
Fluid type:
SAE J1703 or FMVSS No.116 DOT 3

: See “Model code” on page vi in the
beginning of this manual if you are not
sure of your vehicle model.
STEERING
Wheel free play:
Less than 40 mm (1.6 in.)
Power steering fluid type:
Automatic transmission fluid DEXRONrII
or III
Dyna100/150_EE

INDEX225
N
New vehicle break−in 108................
O
Odometer 70............................
Oil
Consumption 115......................
Oil maintenance management
system 70..........................
Viscosity and grade 188................
Oil consumption 115.....................
OMMS 70...............................
Operation in foreign countries 110........
Overheating, Engine 148.................
Overheating, Engine coolant 68..........
Overview
Engine compartment 180...............
P
Parking brake
Operation 82..........................
Reminder light 82.....................
Parking brake reminder light 73...........
Polishing 171...........................
Power window switches 14...............
Pre−trip safety check 126................
Precautions for turning off an engine
with turbocharger 126..................
Preloader (seat belt pretensioner) 35.....
Pretensioner
(seat belt pretensioner) 35.............
Protecting your Toyota from
corrosion 170.........................
R
Radiator
Checking the radiator 192..............
Coolant, Engine 190...................
Rear fog light switch 64..................
Rear heatersystem 92...................
Rear seat 26............................
Rear view mirrors
Folding 59............................
Outside 59............................
S
Safety check, Pre−trip 126...............
Seat belts
Cleaning 173..........................
Fastening 28..........................
Seat belt precautions 28...............
Seat belt pretensioner 35..............
Seats 24................................
Service and maintenance 176............
Service reminder indicator 73............
Side door locks 13.......................
Side doors 13...........................
Side gate 16............................
Side vents 91...........................
Spare fuse 203..........................
Spare tire 150...........................
Specifications 212.......................
SRS driver airbag 38....................
SRS warning light 73....................
Starting
Cold weather 124......................
Engine 124............................
Jump starting 143.....................
Steering
Adjusting steering wheel 58............
Storage precautions 101.................
Suspension and chassis 122.............
Switch
Emergency flasher 64.................
Engine 80.............................
Headlight, dimmer and
turn signal 62.......................
Heater idle up 93......................
Ignition 80............................
Rear fog light 64.......................
Windshield wiper and washer 65........
T
Tachometer 69..........................
Tailgate 16..............................
Telescopic steering wheel 58.............
Tilt cab 18..............................
Tilt steering wheel 58....................
Timing belt replacement
warning light 73.......................
Dyna100/150_EE