2014 Seat Toledo ignition

Emergencies
on battery). Failure to comply could result in
an explosion.
●
Never use jump leads when one of the bat-
teries is frozen. Danger of explosion! Even af-
ter the battery has thawed, battery acid could
leak and cause chemical burns. If a battery
freezes, it should be replaced.
● Keep sparks, flames and lighted cigarettes
away from batteries, danger of explosion.
Failure to comply could result in an explo-
sion.
● Observe the instructions provided by the
manufacturer of the jump leads.
● Do not connect the negative cable from the
other vehicle directly to the negative terminal
of the flat battery. The gas emitted from the
battery could be ignited by sparks. Danger of
explosion.
● Do not attach the negative cable from the
other vehicle to parts of the fuel system or to
the brake line.
● The non-insulated parts of the battery
clamps must not be allowed to touch. The
jump lead attached to the positive battery
terminal must not touch metal parts of the ve-
hicle, this can cause a short circuit.
● Position the leads in such a way that they
cannot come into contact with any moving
parts in the engine compartment.
● Do not lean on the batteries. This could re-
sult in chemical burns. Note
The vehicles must not touch each other, oth-
erwise electricity could flow as soon as the
positive terminals are connected. Towing the vehicle
Introduction Vehicles with manual gearbox can be towed
using a towbar or towrope. They can also be
towed with either the front or rear wheels lif-
ted off the road.
Vehicles with automatic gearbox can be tow-
ed using a towbar or towrope. They can also
be towed with the front wheels lifted off the
road. If the vehicle is towed with the rear
wheels lifted off the road the automatic gear-
box will be damaged!
It is safer to tow a vehicle with a
towbar. A
towrope should only be used if you do not
h av
e a towbar.
Follow the instructions below when towing a
vehicle:
Notes for the driver of the towing vehicle
– Engage the clutch very gently when starting
to move or on vehicles with automatic gear-
box press the accelerator carefully. –
On vehicles with a manual gearbox, the
towrope must be taut before driving off.
Maximum towing speed is 50 km/h (31
mph).
Note

s for the driver of the towed vehicle
– The ignition should be switched on so that
the steering wheel lock is not engaged and
the turn signals, horn and windscreen wip-
ers and washers can be used.
– Put the gear lever in neutral or move the se-
lector lever to position N (automatic gear-
bo

x).
The brake servo and power steering only
work when the engine is running. Considera-
bly more effort is required on the brake pedal
and steering wheel when the engine is
switched off.
Ensure the towrope remains taut at all times
when towing. CAUTION
● Do not tow-start the engine. Risk of engine
damage! In vehicles with a catalytic convert-
er, fuel that has not been burned could reach
the catalytic converter and catch fire in it.
This could damage and destroy the catalytic
converter. You may use the battery from an-
other vehicle to help you start your engine
››› page 158.
» 159
Technical specifications
Advice
Operation
Safety

Advice
Manual release of the selector lever Fig. 135
Manual release of the selector lever. If there is a fault in the power system to the
electronic selector lever lock system (flat bat-
tery, blown fuse) or the system itself is faulty,
the selector lever cannot be moved from po-
sition
P
in the normal manner, which pre-
v
ents the vehicle from being moved. The se-
lector lever must be unlocked using the man-
ual release.
– Apply the handbrake.
– Pull gently on both sides at the front of the
selector lever cover.
– Also loosen the cover at the rear.
– Press the yellow plastic part with your fin-
ger in the direction indicated by the arrow
››› Fig. 135.
– Pre

ss the interlock button on the selector
lever knob at the same time and move the
selector lever to position N (if the selector l
ever is moved back to position
P, it will
lock again).
Changing the wiper blades Changing the windscreen wiper
blades Fig. 136
Windscreen wiper blades. Set the windscreen wiper arms to the service
position before changing the blades.
Service position for changing wiper blades
– Close the bonnet.
– Switch the ignition on and off.
– Press the lever to position 4
››› Fig. 56
››› page 69, the windscreen wiper arms are
set to the service position. Taking off the wiper blade
–
Lift the windscreen wiper arm away from
the glass moving the blade slightly in the
direction of the arm – arrow A
››› Fig. 136 .
– Ho l

d the top of the windscreen wiper arm
with one hand.
– Unlock the catch 1 with the other hand
and remove the blade in the direction of ar-
row B .
Fitting the wiper blade – Slide the blade fully until it clicks into posi-
tion.
– Check that the wiper is correctly secured.
– Fold the windscreen wiper arm back down
onto the glass.
– Switch the ignition on and press the lever
to position 4
››› Fig. 56 ››› page 69, the
windscreen wiper arms are set to the basic
position.
162

Fuses and bulbs
Changing the rear window wiper
blade* Fig. 137
Rear window wiper blade. Taking off the wiper blade
–
Lift the rear window wiper arm away from
the glass moving the blade slightly in the
direction of the arm – arrow A
››› Fig. 137 .
– Ho l
d the top of the rear window wiper arm
with one hand.
– Unlock the catch 1 with the other hand
and remove the blade in the direction of ar-
row B .
Fitting the wiper blade – Slide the blade fully until it clicks into posi-
tion.
– Check that the wiper is correctly secured.
– Fold the rear window wiper arm back down
onto the glass. Fuses and bulbs
Fuses Introduction Due to the constant updating of vehicles,
fuse assignments based on equipment and
the use of the same fuse for various electrical
components, it is not possible to provide an
up-to-date summary of the fuse positions for
the electrical components at the time this
manual was printed. For detailed information
about the fuse positions, please consult a
technical service.
In general, a fuse can be assigned to various
electrical components. Likewise, an electrical
component can be protected by several
fuses.
Only replace fuses when the cause of the
problem has been solved. If a newly inserted
fuse blows after a short time, you must have
the electrical system checked by a special-
ised workshop as soon as possible.
Additional information and warnings:
● Working in the engine compartment
››› page 132 . WARNING
The high voltages in the electrical system can
give serious electrical shocks, causing burns
and even death!
● Never touch the electrical wiring of the igni-
tion system.
● Take care not to cause short circuits in the
electrical system. WARNING
Using unsuitable fuses, repairing fuses or
bridging a current circuit without fuses can
cause a fire and serious injury.
● Never use a fuse with a higher value. Only
replace fuses with a fuse of the same amper-
age (same colour and markings) and size.
● Never repair a fuse.
● Never replace a fuse by a metal strip, staple
or similar. CAUTION
● To prevent damage to the vehicle's electric
system, before replacing a fuse always turn
off the ignition, the lights and all electrical
elements and remove the key from the igni-
tion.
● If you replace a fuse with higher-rating
fuse, you could cause damage to another part
of the electrical system.
● Protect the fuse boxes when open to pre-
vent the entry of dust or humidity as they can
damage the electrical system. » 163
Technical specifications
Advice
Operation
Safety

Fuses and bulbs
Changing fuses in the engine
compartment Fig. 140
Battery: fuse cover (version 1). Fig. 141
Battery: fuse cover (version 2). ●
Press the flexible tabs on the fuse box cov-
er in the direction indicated by the arrows 1 ›››
Fig. 140 .
● Remo
ve the cover by sliding it in the direc-
tion indicated by arrow 2 .
● Use a flat-headed screwdriver to unlock the
holes 3 .
● Open the cover in the direction indicated
by the arrow 4 .Replacing a blown fuse
Fig. 142
Image of a blown fuse Preparation
● Switch off the ignition, lights and all elec-
trical equipment.
● Open the corresponding fuse box
››› page 164 .
Identif y

ing a blown fuse
A fuse is blown if its metal strip is ruptured
››› Fig. 142.
Point a lamp at the fuse. This will make it
easier to see if the fuse is blown.
To replace a fuse ● Remove the fuse.
● Replace the blown fuse by one with an
identical amperage rating (same colour and
mark

ings) and identical size ››› .
»
165
Technical specifications
Advice
Operation
Safety

Advice
● Replace the cover again or close the fuse
box lid. CAUTION
If you replace a fuse with higher-rating fuse,
you could cause damage to another part of
the electrical system. Changing bulbs
Introduction Changing bulbs requires a certain degree of
practical skill. If in doubt, we recommend you
have defective bulbs changed by a special-
ised service or, in case of an emergency,
seek professional assistance.
●
Switch off the ignition and all of the lights
before changing a bulb.
● Do not touch the glass part of the bulb with
your bare hands. The fingerprints left on the
glass will vaporise as a result of the heat gen-
erated by the bulb, reducing bulb life and
causing condensation on the reflector sur-
face, thus reducing effectiveness.
● A bulb must only be replaced by one of the
same type. The type is indicated on the bulb,
either on the glass part or on the base.
● There is a storage area for the bulb box in
the spare wheel well or below the carpet in
the luggage compartment. The light source used for each function is lis-
ted below:
Double headlights
H7 Long Life
H7
W5W Long Life PY21W NA P21W Super Long Life WARNING
● Take particular care when working on com-
ponents in the engine compartment if the en-
gine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The
glass can break when you touch the bulb,
causing injury.
● The high voltage element of gas discharge
bulbs* (xenon light) must be handled correct-
ly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not
to injure yourself on sharp parts in the head-
light housing. CAUTION
● Remove the ignition key before working on
the electric system. Otherwise, a short circuit
could occur.
● Switch off the lights and the parking light
before changing a bulb. Dipped beam:
Main beam:
Side lights:
Turn signals:
Daytime driving lights: For the sake of the environment
Please ask your specialist retailer how to dis-
pose of used bulbs in the proper manner. Note
● Depending on weather conditions (cold or
wet), the front lights, the fog lights, the rear
lights and the turn signals may be temporari-
ly misted. This has no influence on the useful
life of the lighting system. By switching on
the lights, the area through which the beam
of light is projected will quickly be demisted.
However, the edges may continue to be mis-
ted.
● Please check at regular intervals that all
lighting (especially the exterior lighting) on
your vehicle is functioning properly. This is
not only in the interest of your own safety,
but also that of all other road users.
● Before changing a bulb, make sure you
have the correct new bulb.
● Do not touch the glass part of the bulb with
your bare hands, use a cloth or paper towel
instead. Otherwise, the fingerprints left on
the glass will vaporise as a result of the heat
generated by the bulb, they will be deposited
on the reflector and damage its surface. 166

Index
H
Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Hazard warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
HBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Head-on collisions and the laws of physics . . . . . 13
Head-protection airbags . . . . . . . . . . . . . . . . . . . . 21 safety instructions . . . . . . . . . . . . . . . . . . . . . . . 22
Headlights Driving abroad . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Headlight washer system . . . . . . . . . . . . . . . . . . 70
Head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Headrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Heated rear window . . . . . . . . . . . . . . . . . . . . . . . . 67
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 air recirculation . . . . . . . . . . . . . . . . . . . . . . . . . . 90
defrosting windows . . . . . . . . . . . . . . . . . . . . . . 89
exterior mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 70
rear window . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
HHC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Hill-hold control . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
How to jump start description . . . . . . . . . . . . . . . 158
I Identification plate . . . . . . . . . . . . . . . . . . . . . . . . 174
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Immobiliser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Informative display see MAXI DOT . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Interior ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
cigarette lighter . . . . . . . . . . . . . . . . . . . . . . . . . 78
lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Storage compartment . . . . . . . . . . . . . . . . . . . . 76 ISOFIX system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
J Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Jump-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
K
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
L
Lever main beam headlights . . . . . . . . . . . . . . . . . . . . 63
turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Lifting the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 153
Lights AUTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
changing bulbs . . . . . . . . . . . . . . . . . . . . . . . . . 166
control lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Daytime driving light . . . . . . . . . . . . . . . . . . . . . 62
dipped beam . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
front fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Front fog lights with cornering function . . . . . . 64
hazard warning lights . . . . . . . . . . . . . . . . . . . . 65
headlight flasher . . . . . . . . . . . . . . . . . . . . . . . . 63
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Main beam headlights . . . . . . . . . . . . . . . . . . . . 63
parking lights . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
parking lights on both sides . . . . . . . . . . . . . . . 65
range control of main lights . . . . . . . . . . . . . . . . 62
rear fog light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
side lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
switching lights on and off . . . . . . . . . . . . . . . . 61
turn signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Load compartment in the luggage compartment
see Loading the luggage compartment . . . . . . 81
L o
ading the luggage compartment . . . . . . . . . . . . 81
Locking central locking system . . . . . . . . . . . . . . . . . . . . 55
manual locking . . . . . . . . . . . . . . . . . . . . . . . . . 161
remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Locking a gear . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Luggage carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Luggage compartment Category N1 vehicles . . . . . . . . . . . . . . . . . . . . . 83
light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
manual release . . . . . . . . . . . . . . . . . . . . . . . . . 161
Manual release of the rear lid . . . . . . . . . . . . . 161
shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
see also Loading the luggage compartment . . 81
M Mak

e-up
mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Manual door locking . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
release of the rear lid . . . . . . . . . . . . . . . . . . . . 161
Release of the selector lever . . . . . . . . . . . . . . 162
Manual gearbox Gear lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
MAXI DOT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
MDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Mirror exterior mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Interior rear vision mirror with manual anti-dazzle adjustment . . . . . . . . . . . . . . . . . . . . . 70
Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Multi-function display function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
190