2014 RENAULT SCENIC oil pressure

PETROL INJECTION
Fault finding – System operation17B
17B - 7V12 MR-372-J84-17B000$090.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48PETROL INJECTION
Fault finding – System operation
1. SYSTEM OPERATION
Composition
The injection system consists of the:
– accelerator potentiometer,
– accelerator pedal switch,
– TDC sensor,
– atmospheric pressure sensor,
– air temperature sensor,
– coolant temperature sensor,
– freon pressure sensor,
– upstream oxygen sensor,
– downstream oxygen sensor,
– cruise control switch,
– steering column switch,
– cruise control on/off switch,
– brake lights switch,
– fuel vapour absorber,
– injection computer,
– motorised throttle valve,
– four injectors,
– four pencil coils,
– + turbocharging pressure sensor,
– coolant pump
– turbocharging solenoid valve.
Computer
SAGEM S3000 flash EEPROM 128-track computer controlling the injection and the ignition.
Multipoint injection in sequential mode.
Connections to the other computers:
– Protection and Switching Unit (UPC)
– Passenger Compartment Control Unit (UCH),
– Automatic Transmission Electronic Control Unit (AUTO ECU).
JSAA741.0
MR-372-J84-17B000$090.mif

PETROL INJECTION
Fault finding – Interpretation of faults17B
17B - 84V12 MR-372-J84-17B000$405.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
DF612
PRESENT
OR
STOREDOIL VAPOUR DEFREEZE RESISTOR CIRCUIT
CO.0 : open circuit or short circuit to earth
NOTESPriority for dealing with a combination of faults:
If the faults DF002 Air temperature sensor circuit, DF004 Turbocharging pressure
circuit, DF009 Gang 2 pedal potentiometer circuit or DF046 Battery voltage are
present, handle them first.
Conditions for applying the fault finding procedure to stored faults:
The fault appears after the ignition has been switched on.
Check the cleanliness and condition of the oil vapour defreeze resistor relay connections.
Clean or replace as necessary.
Measure the resistance of the defreeze resistor relay between tracks 1 and 2.
Replace the relay if the resistance is not:21at - 40 °C
9.5at 20 °C
13.4at 120 °C
With the ignition on, check for + 12 V on track 1 of the defreeze resistor relay.
Repair if necessary.
Disconnect the battery.
Disconnect the computer. Check the cleanliness and condition of the connections.
Using the Universal bornier, check the insulation, continuity and the absence of interference resistance for
the following connection:
Computer, connector B, track L2 track 2 of the oil vapour defreeze relay
Repair if necessary.
If the fault is still present, deal with the other faults, then proceed to the conformity check.
AFTER REPAIRFollow the instructions to confirm repair.
Deal with any other faults.
Clear the stored faults.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-92V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application condition: engine off, ignition on.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Engine
speedPR055: Engine speedIndicates the engine's speed
of rotation in rpm.
0 rpm < PR055 < 500 rpmIn the event of a fault
apply the interpretation
for DF154 Flywheel
signal sensor circuit.
2
Motorised
throttlePR014: Idling speed
correctionShows engine idling speed
correction value.
PR014= 0rpm.
The idle speed regulator
performs all of the
calculations that allow the idle
speed actuator to be
controlled physically: the
motorised throttle. The
functional component of the
regulator is adaptive
(variation programming and
ageing).WITHOUT
3 PR054: Idle speed
regulationACTIVE
INACTIVEIf ACTIVE apply the
interpretation for ET054
Idle speed regulation.
4 PR010: Idle speed
regulation
setpointThe idle speed regulation
setpoint depends on the
coolant and oil temperature,
the position of the gear lever,
and which electrical
consumers are operating.
752 rpm. < PR010
< 1216 rpm.
If a manifold pressure sensor
fault is present or stored, the
idle speed setting is 896 rpm.In the event of a fault
apply the interpretation
for ET054, Idle speed
regulation.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B-113V12 MR-372-J84-17B000$450.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
FUEL CIRCUIT SUB-FUNCTION
NOTESOnly check conformity after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, at idle speed.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1Engine
speedPR055: Engine
speedIndicates the engine's speed of
rotation in rpm.
700 rpm < PR055 < 6500 rpmIn the event of a
fault, apply the
interpretation for
DF154 Flywheel
signal sensor
circuit.
2
Motorised
throttlePR014: Idling
speed
correctionShows engine idling speed
correction value.
0 rpm < PR014 < 224 rpm.
The idle speed regulator performs all
of the calculations that allow the idle
speed actuator to be controlled
physically: the motorised throttle.
This regulator has a built-in adaptive
component (variation and ageing
programming).WITHOUT
3ET054: Idle speed
regulationACTIVE
INACTIVEIf INACTIVE apply
the interpretation for
ET054 Idling speed
regulation.
4 PR010: Idle speed
regulation
setpointThe idle speed regulation setpoint
depends on the coolant and oil
temperature, the position of the gear
lever, and which electrical
consumers are operating.
752 rpm < PR010 < 1216 rpm.
If a manifold pressure sensor fault is
present or stored, the idle speed
setting is 896 rpm.In the event of a
fault, apply the
interpretation of
ET054 Idle speed
regulation.
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of statuses17B
17B - 140V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ET054
IDLING SPEED REGULATION
NOTESThere must be no present or stored faults.
Check the parameters PR032, PR058, PR064, PR118, PR119 and PR030.
Check that all these parameters are completely correct.
IDLING SPEED
TOO LOW
Check:
– the engine oil level (too high  splashing),
– that the exhaust pipe is not blocked (catalytic converter damaged),
– the cleanliness and conformity of the air filter,
– that the air inlet circuit is not blocked,
– that the throttle valve is not clogged,
– the condition and conformity of the spark plugs,
– the fuel circuit sealing,
– the fuel pressure and flow (see MR 364 Mechanics, 17B, Petrol injection),
– the condition and cleanliness of the injectors,
– the cylinder compression's,
– the timing adjustment,
– the hydraulic tappets if there is camshaft noise (see MR 364 Mechanics, 11A, Top and front of engine).
Repair the defective component if necessary.
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of statuses17B
17B - 141V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ET054
CONTINUED
IDLING SPEED
TOO HIGH
Check:
– the engine oil level (too high  oil combustion),
– that the restrictions are present in the oil vapour rebreathing circuit,
– the sealing between the throttle valve and inlet manifold,
– the manifold pressure sensor sealing,
– the fuel vapour absorber bleed, which must not be jammed open,
– the fuel vapour absorber bleed system sealing,
– the brake servo system sealing,
– the sealing between the inlet manifold and cylinder head,
– the oil vapour recovery circuit sealing between the inlet manifold and cylinder head,
– the fuel pressure and flow (see MR 364 Mechanics, 17B, Petrol injection),
– the condition and cleanliness of the injectors,
– the cylinder compression's,
– the timing adjustment,
– the hydraulic tappets if there is camshaft noise (see MR 364 Mechanics, 11A, Top and front of engine).
Repair the defective component if necessary.
AFTER REPAIRRepeat the conformity check from the start.
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of statuses17B
17B - 143V12 MR-372-J84-17B000$540.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
ET055
CONTINUED
Check:
– the condition of the air filter,
– that the air inlet circuit is not blocked,
– the condition and conformity of the spark plugs,
– the sealing between the throttle valve and inlet manifold,
– the manifold pressure sensor sealing,
– the fuel vapour absorber bleed, which must not be jammed open,
– the fuel vapour absorber bleed system sealing,
– the brake servo system sealing,
– the turbocharger safety valve circuit sealing,
– the cylinder head oil vapour recovery system sealing,
– the sealing between the inlet manifold and cylinder head,
– the exhaust pipe sealing between the cylinder head and catalytic converter.
– the fuel flow rate and pressure.
If the idling speed is not stable, check:
– the timing adjustment,
– the hydraulic tappets if there is camshaft noise (seeMR 364 Mechanical, 11A, Top and front of engine),
– the cylinder compression's.
Drive the vehicle to check the repair.
Repair the defective components.
AFTER REPAIRRepeat the conformity check from the start.
JSAA741.0

PETROL INJECTION
Fault finding – Interpretation of parameters17B
17B - 159V12 MR-372-J84-17B000$675.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
PR032
INLET PRESSURE
NOTESThere must be no present or stored faults.
Check the cleanliness and condition of the manifold pressure sensor and its connections.
Repair if necessary.
Disconnect the battery and the injection computer.
Check the cleanliness and condition of the connections.
Using the Universal bornier, check the insulation and continuity of the following connections:
Computer, connectorB, track H2 track 1 of the manifold pressure sensor.
Computer, connectorB, track H3 track 3 of the manifold pressure sensor
Computer, connectorB, track H4 track 2 of the manifold pressure sensor
Repair if necessary.
If the fault is still present, replace the manifold pressure sensor.
If the fault is still present, carry out the following checks:
The inlet line must be perfectly sealed, from the throttle valve to the cylinder head.
Check:
– the condition of the air filter,
– that the air inlet circuit is not blocked,
– the sealing between the throttle valve and inlet manifold,
– the manifold pressure sensor sealing,
– the fuel vapour absorber bleed, which must not be jammed open,
– the fuel vapour absorber bleed system sealing,
– the brake servo system sealing,
– that there are no leaks in the turbocharger safety valve circuit,
– the cylinder head oil vapour recovery system sealing,
– the sealing between the inlet manifold and cylinder head,
– the exhaust pipe sealing between the cylinder head and catalytic converter.
Repair if necessary.
AFTER REPAIRRepeat the conformity check from the start.
JSAA741.0