2014 PORSCHE 911 TURBO start stop button

Overview Illustrations 13
Control Panel
ASeat heating/seat ventilation See page 35.B Operating panel for air conditioning See page 55.C Central locking button See page 18.D Front/rear spoiler See page 190.E Auto Start-Stop function/coasting mode See page 151.F Emergency flasher switch See page 83.G Sport mode See page 188.H Sport Plus mode See page 188.I Porsche Active Suspension Management (PASM)See page 185.J Porsche Stability Management (PSM) See page 180.K Operating panel for lifting/sliding roof See page 63.Control panel for convertible topSee page 67.
14_991_Turbo_21.book Seite 13 Mittwoch, 9. April 2014 2:19 14

66 Windows, Sunroof and Cabriolet
1.Carefully lever off the cap from the roof liner using a screwdriver, for example.2. Take the hexagon key out of the tool kit in the luggage compartment.
For information on the tool kit:fPlease see the chapter “TOOLS” on page 198.
3. Insert the hexagon key all the way into the opening.4. Applying continuous upward pressure, turn the key clockwise until the roof is fully closed.5. Remove the key. 6. Refit the cap. 7. Stow the key in the tool kit.fHave the fault corrected at an authorized Porsche dealer.
Storing end position of the sunroof
The end positions of the roof are lost after disconnection/connection of the vehicle battery, if the vehicle battery is exhausted or after jump lead starting, after emergency operation or after changing the fuse for the roof.
The roof closes with its full closing force when storing the end position.fEnsure that nobody is injured when closing the roof.
The vehicle must be stationary in order to store the end position of the roof.1. Switch on ignition. 2. Pull and hold button C in the first setting until the roof closes and stops in the closed position.The process for storing the end position begins after approximately 10 seconds. The roof now opens and closes once automatically. Storage is now complete.If this process is not executed, please perform the following procedure:Pull and hold button C in the first setting until the roof closes fully and stops. If necessary, repeat the closing operation until the roof has stopped moving completely.The process takes a maximum of 15 seconds.Start the storing process again if the button is released before the roof has stopped moving completely.
Storing the end positionWARNINGh
14_991_Turbo_21.book Seite 66 Mittwoch, 9. April 2014 2:19 14

Windows, Sunroof and Cabriolet 67
Storing end position of the roll-up sunblind
The end positions of the sunblind are lost after disconnecting/connecting the vehicle battery,
if the vehicle battery is exhausted or after jump lead starting, after emergency operation or after changing the fuse for the sunblind.
The sunblind closes with its full closing force when storing the end position.fEnsure that nobody is injured when closing the sunblind.
To store the end position for the sunblind, the vehicle must be stationary and the end position for the roof must already be stored.1. Switch on ignition. 2. Press and hold button A in the first setting until the sunblind closes and stops in the closed position.The process for storing the end position begins after approximately 10 seconds. The sunblind now opens and closes once automatically. Storage is now complete.If this process is not executed, please perform the following procedure:Press and hold button A in the first setting until the sunblind closes fully and stops. If necessary, repeat the closing operation until the sunblind has stopped moving completely.The process takes a maximum of 15 seconds.Start the storing process again if the button is released before the sunblind has stopped moving completely.
Cleaning the air deflector
Cleaning the air deflector with the roof open.
1. Switch on the ignition and open the roof fully with button B. If the air deflector is not fully extended, drive the vehicle for a short distance with the roof open until it is fully extended.2. Clean the air deflector and net using a damp sponge.
Convertible Top
Brief operating instructions can be found on the back of the driver’s sun visor.fPlease see the chapter “CAR CARE INSTRUCTIONS” on page 231.
Risk of damage to convertible top and convertible- top mechanism.fDo not operate convertible top:– At temperatures below 20 °F (0 °C).– When one side of the vehicle is on a curb, a lifting platform or a jack.– When items of luggage or other objects hinder the movement of the convertible top.– With the roll-over bars extended.fAvoid frequent operation of the convertible top with the engine off; the vehicle battery will rapidly discharge.fOnly drive with the convertible top fully open or closed (end positions).fBefore opening the convertible top, ensure that there are no objects in the area behind the rear seats.fWhen opening or closing the convertible top, ensure that there is sufficient clearance above it (e.g. in the garage).fTo prevent damp stains and abrasion damage, open the convertible top only when it is in a dry, clean state.fPark the vehicle in the shade if possible, since continuous exposure to the sun attacks textiles, rubber and colors.fThe convertible top may only be operated when driving on a level surface.fThe convertible top must not be operated in a strong head wind (above approx. 50 mph (80 km/h)).
Storing the end positionWARNINGh
NOTICE
14_991_Turbo_21.book Seite 67 Mittwoch, 9. April 2014 2:19 14

Lights, Turn Signals and Windshield Wipers 87
Rain sensor operation, windshield wipers
In rain sensor mode, the amount of rain on the windshield is measured. The wipe interval is automatically controlled accordingly.
Rain sensor operation is activated automatically at speeds of less than approx. 2.5 mph (4 km/h) when the windshield wipers are switched on.
If a speed of approx. 5 mph (8 km/h) is exceeded, the system switches to the preselected wiper speed.
Information
fIf the wiper stalk is in position 1 when the ignition is switched on, the rain sensor is activated as soon as the vehicle speed exceeds approx. 2.5 mph (4 km/h).fIf the wiper stalk is in position 2 or 3 when the ignition is switched on, the windshield wipers remain switched off until the wiper stalk is actuated.
Information
The wiper is stopped when the luggage compartment lid is opened.
After closing the luggage compartment lid, the wiper stalk must be operated in order to switch the wiper back on.
Adjusting the rain sensor sensitivity
fMove switch A upwards – high sensitivity . The setting is confirmed by one wipe of the windshield.fMove switch A downwards – low sensitivity .
Activating and deactivating automatic rain sensor operation on the multi-function display
For information on automatic rain sensor operation:fPlease see the chapter “ACTIVATING AND DEACTIVATING RAIN SENSOR OPERATION” on page 121.
Headlight washer system
The washer sprays only while low beam or high beam is activated. fPress button B under the wiper stalk.
After every 10 wipes on the windshield, the headlights are cleaned automatically as well. The wipe count starts from zero again when the low beam is switched off.
14_991_Turbo_21.book Seite 87 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 99
Info
Oil measurement LimitsSettings
Station/Track
Answer/Reject/End
Phonebook
Previous calls
Received calls
Manual zoom Auto zoom3D map North up
Show destination/position
Destination input
Start/Stop route guidance
Since
Total
To destination
Fill info Tire typePartial/full load Comfort/standard pressure
Start StopRoundInt.
Torque
Current speed
Setting the speed
Menu scope
Audio
Vehicle menu
Upper line
PCM display
Lower line
Shift request
Brightness
Exterior lights
Interior lights
Wiper
Revers. opt.
Door lock/unlock
Comfort Entry
Auto Memory
Air flow
Vent. panel
Auto air circ.
Time
Date
DST (+01:00)
Time Chrono
Speedometer
Temperature
Tire pressure
Consumption
German/French...
ParkAssist
Warn. tones
◊ button
Messages
Service interval
Limit 1/Limit 2
Display
Light & Visibility
Locking
Air conditioning
Date & Time
Units
Language
Volume
Steering wheel op.
Fact. settings
Last destination
Stored destinations
POIs
Cont.
Reset
Vehicle
Audio
Telephone
Map
Navigation
Trip
Tire pressure
Allwheel
Chrono
G-Force
Performance
ACC
14_991_Turbo_21.book Seite 99 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 127
Adjusting volume of warning tones
The volume of the warning tones can be adjusted individually.
Available setting options: –“ Loud” –“ Medium” –“ Low”
Changing button assignment on multi-function steering wheel
The assignment of the ◊ button on the multi-function display can be changed individually.Functions from the multi-function display or PCM/CDR can be assigned to the ◊ button.
Available PCM functions: –“ Source change” Change audio source.–“ Voice control” Activate voice control.–“ Dri. instr. (Rep)” Repeat voice instruction from the navigation system.–“ Station/track <” Previous radio station/title.–“ Station/track >” Next radio station/track.–“ Map” Display navigation map in PCM.–“ Menu change” Change main menu area.
Available instrument cluster functions: –“ Start/Stop Chr.” Start/stop timing.–“ Vehicle menu” Display vehicle menu.–“ Trip menu” Display trip menu.–“ TPMS menu” Display TPMS menu.–“ Chrono menu” Display Chrono menu.–“ Audio menu” Display audio menu.–“ Phone menu” Display telephone menu.–“ Navi menu” Display navigation menu.–“ Map menu” Display navigation map on the multi-function display.
1. Main menu “Vehicle” > “ Settings” > “ Volume”
2.Select “Warn. tones”. in the main menu.
3. Select the desired setting and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Steering wheel op.”
2.Select “◊ button” and confirm.
3. Select “PCM function” or “ Inst. clus. fun.” and confirm.
4. Select the desired function assignment and confirm.
14_991_Turbo_21.book Seite 127 Mittwoch, 9. April 2014 2:19 14

150 Driving and Driving Safety
Information
The engine will start automatically in certain situations, e.g. if the vehicle starts rolling, if air conditioning causes reduced comfort, or if the brake vacuum is reduced.The engine is stopped again automatically if the preconditions for stopping the engine automatically are then met again.
Exceptions for the Auto Start Stop function
The Auto Start Stop function is deactivated e.g.: – When Sport mode is activated.– When PSM is off.– In maneuvering mode.– When A/C MAX mode is activated.– When the “Windshield defrost” function is active. – At altitudes above approx. 9,843 ft. (3,000 meters)
For information on switching on and off the Auto Start Stop function:fPlease see the chapter “SWITCHING AUTO START STOP FUNCTION AND COASTING MODE ON AND OFF” on page 150.
The Auto Start Stop function is available with limited functionality in the following situations, e.g.:– If the air conditioning or passenger compartment heating is operated at a high setting or if the defrost function is run for long time periods.– If the battery charging condition is low.– On upward or downward slopes.– During internal vehicle test procedures, e.g. automatic engine checks.
Information
If one of these situations arises after the engine has stopped automatically, the engine can be restarted automatically.
Reaction after leaving the vehicle (selector-lever position D or N selected)
If the vehicle is left after an automatic stop when PDK selector-lever position D or N is engaged, an automatic engine start is executed to remind the driver that the Auto Start Stop function is still active.
In selector-lever position D, the electric parking brake is additionally engaged.
The brake warning light on the instrument panel and the indicator light on the switch light up.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Reaction after leaving the vehicle (selector-lever position P selected)
If the vehicle is left after an automatic stop when PDK selector-lever position P is engaged, in order to open the garage door, for example, no automatic engine start is executed. Auto Start Stop mode is resumed if the driver closes the driver’s door and presses the brake within 30 seconds of leaving the vehicle.
If one of these requirements is not met, the engine has to be started manually. The
message “ Please start engine manually” will appear on the multi-function display in the instrument panel.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Switching Auto Start Stop function and coasting mode on and off
Switching off
fPress button . The indicator light on the button lights up.Automatic stopping of the engine is suppressed and gliding mode is switched off.
Switching on
fPress button . The indicator light on the button goes out.The engine is automatically stopped when the vehicle stops and gliding mode is switched on.fPlease see the chapter “DRIVING IN COASTING MODE” on page 174.
14_991_Turbo_21.book Seite 150 Mittwoch, 9. April 2014 2:19 14

172 Driving and Driving Safety
Porsche Doppelkupplung (PDK)
Porsche Doppelkupplung (PDK) is a seven-speed transmission with an automatic and a manual selection mode.
In automatic selection mode (selector-lever position D), gear changing is automatic. You can change temporarily from automatic to manual mode using the shift buttons on the steering wheel.
In manual selection mode (selector-lever position M), you change gear using the shift buttons or shift paddles on the steering wheel or with the PDK selector lever.
You can change between selector-lever positions D and M as you wish while driving.
Information
fTake care not to operate the shift buttons on the steering wheel inadvertently in either automatic or manual mode, thereby triggering undesired gear changes.
Changing selector-lever position
The selector lever is blocked in the P position when the ignition is switched off.
When the ignition is switched on, the selector lever can be moved from position P and N only when the release button is pressed, and when the brake pedal is pressed.
Release button
The release button ( arrow) in the selector lever prevents the gear from being changed unintentionally.The release button must be pressed when shifting to position R or P.
Starting
The engine can be started only if the brake pedal is depressed and the selector lever is in position P or N.
Driving off
fOnly select the desired position for driving off ( D, M or R) when the engine is idling and the brake pedal is pressed.fSince the vehicle crawls when in gear, do not release the brake until you are ready to drive off.
Driving off on hills
The Drive-Off Assistant assists the driver when driving off on hills. The vehicle is held on the slope for a short time during the change from the brake pedal to the accelerator to facilitate driving off immediately after the brake is released.fPlease see the chapter “HOLD FUNCTION: DRIVE-OFF ASSISTANT, STANDSTILL MANAGEMENT” on page 184.
Stopping
fFor a brief stop, e.g. at traffic lights, leave the selector lever in drive position and hold the vehicle with the brake pedal.fDo not hold the vehicle on a slope using the accelerator. Use the brake pedal or the electric parking brake instead.fBefore leaving the vehicle, always apply the electric parking brake and move the selector lever to position P.
Parking
fGo easy on the accelerator!fWhen parking or maneuvering in a small space, control the speed by careful use of the footbrake.
14_991_Turbo_21.book Seite 172 Mittwoch, 9. April 2014 2:19 14