2014 Peugeot 308 ignition

68
Access
308_EN_CHAP02_OUVERTURES_ED02-2013
Triggering of the alarm
This is indicated by sounding of the siren and flashing of the direction indicators for thirty seconds. The monitoring functions remain active until the alarm has been triggered eleven times in succession.
When the vehicle is unlocked using the remote control or the Keyless Entry and starting system, rapid flashing of the indicator lamp in the button informs you that the alarm was triggered during your absence. When the ignition is switched on, this flashing stops immediately.
Failure of the remote control
To deactivate the monitoring functions:  Unlock the vehicle using the key (integral with the remote control) in the driver's door lock.  Open the door; the alarm is triggered.  Switch on the ignition; the alarm stops. The
indicator lamp in the button goes off.
Locking the vehicle without
activating the alarm
 Lock or deadlock the vehicle using the key (integral with the remote control) in the driver's door lock.
Operating fault
When the ignition is switched on, fixed illumination of the indicator lamp in the button indicates a fault in the system. Have it checked by a PEUGEOT dealer or a qualified workshop.
Automatic activation
This function is either not available, an option or is standard. 2 minutes after the last door or the boot is closed, the system is activated automatically.  To avoid triggering the alarm on entering the vehicle, first press the unlocking button on the remote control or unlock the vehicle using the Keyless Entry and Starting system.

69
2
Access
308_EN_CHAP02_OUVERTURES_ED02-2013
Electric windows
1. Left hand front electric window.2. Right hand front electric window.3. Right hand rear electric window.4. Left hand rear electric window.5. Deactivating the rear electric window switches.
Manual operation
To open or close the window, press or pull the switch fully: the window opens or closes completely when the switch is released. Pressing the switch again stops the movement of the window. The electric window switches remain operational for approximately one minute after the key has been removed. Once this time has elapsed, the electric windows will not operate. To reactivate them, switch the ignition on again.
Safety anti-pinch
(depending on version)
Automatic one-touch operation
(depending on version)
To open or close the window, press or pull the switch gently. The window stops as soon as the switch is released.
When the window rises and meets an obstacle, it stops and immediately partially lowers again. In the event of unwanted opening of the window when closing automatically, press the switch until the window opens completely, then pull the switch immediately until the window closes. Continue to hold the switch for approximately one second after the window has closed. The safety anti-pinch function is not active during this operation.
Maintaining the locking action (on the key or the remote control) closes the windows automatically.

71
2
Access
308_EN_CHAP02_OUVERTURES_ED02-2013
Panoramic sunroof
Opening
 Press the back of the control without going beyond the point of resistance. The blind stops when your release the control.
Electric blind
Closing
 Press the front of the control without going beyond the point of resistance. The blind stops when your release the control.
Anti-pinch
If the blind encounters an obstacle, you should reverse the movement. Use the control to do this.
A panoramic tinted glass sur face to improve brightness and vision in the passenger compartment. Its electric blind improves thermal and acoustic comfort.
You can also press or pull the control beyond the point of resistance: the blind opens or closes completely after you release the control. Operating the
control again stops the movement of the blind.
Remember to always switch off the ignition when leaving the vehicle, even for a short time. When operating the control, the driver should ensure that there is nothing preventing movement of the blind. The driver must ensure that passengers use the blind correctly. Be aware of children when operating the blind.

72
Access
308_EN_CHAP02_OUVERTURES_ED02-2013
Fuel tank
Additions of fuel must be of at least 10 litres to be registered by the fuel gauge. Opening the filler cap may result in an inrush of air. This vacuum is entirely normal and results from the sealing of the fuel system.
Opening
With Stop & Start, never refuel with the system in STOP mode; you must switch off the ignition with the key, or the START/STOP button if your vehicle has
Keyless Entry and Starting.
- If your vehicle has Keyless Entry and Starting, unlock the vehicle. - Press the filler flap (on the rear side of the vehicle) then pull it.
Refuelling
 Remove the filler cap and hang it on its carrier (on the filler flap).  Introduce the nozzle and push it in fully (pushing on the the metal non-return valve A ). A ). A Fill the tank. Do not continue past the third cut-off of the nozzle, as this may cause malfunctions.  Refit the filler cap turning it to the right.  Push the filler flap to close it (your vehicle must be unlocked).
 Take care to select the pump that delivers the correct fuel type for your vehicle's engine (reminder on a label on the inside of the filler flap).  Introduce the key into the filler cap, if your vehicle has a normal key.  Turn the filler cap to the left.
Capacity of the tank: approximately 53 litres (or 45 litres according to version).

78
Comfort
308_EN_CHAP03_CONFORT_ED02-2013
System which registers the electrical settings of the driver's seat and door mirrors. It enables you to store and recall two positions using the buttons on the side of the driver's seat.
Storing driving positions
Storing a position
Using buttons M / 1 / 2
 Switch on the ignition.  Adjust your seat and the door mirrors.  Press button M , then press button 1 or 2within four seconds. An audible signal indicates that the position has been stored. Storing a new position cancels the previous position.
Recalling a stored position
Ignition on or engine running
 Press button 1 or 2 to recall the corresponding position. An audible signal confirms that adjustment is complete. You can interrupt the current movement by pressing button M , 1 or 2 or by using one of the seat controls. A stored position cannot be recalled while driving. Recalling stored positions is deactivated 45 seconds after switching off the ignition.

101
3
Comfort
308_EN_CHAP03_CONFORT_ED02-2013
Dual-zone digital air conditioning (Touch screen)
This air conditioning system operates with the engine running, but the ventilation and its controls are available with the ignition on. Operation of the air conditioning and regulation of temperature, air flow and air distribution in the passenger compartment are automatic according to the temperature in the passenger compartment and the temperature setting.
Temperature adjustment
The driver and front passenger can each set the temperature.
 Press one of these buttons to increase the value.
The value indicated corresponds to a level of comfort and not to a temperature in degrees Centigrade or Fahrenheit (depending on the units chosen). A setting around 21 provides an optimum level of comfort. Depending on your requirements, a setting between 18 and 24 is normal. In addition, it is recommended that you avoid a difference between the left and right setting of
more than 3.
Press the button for the " Air conditioning " menu to display the controls for the air conditioning system.  Press one of these buttons to decrease the value.

104
Comfort
308_EN_CHAP03_CONFORT_ED02-2013
"Mono" function
The comfort setting for the passenger's side can be indexed to the driver's comfort setting (mono-zone).
From the secondary page of the " Air conditioning " menu:
 Press this button to activate / deactivate the "Mono" function. The indicator lamp in the button is on when the function is activated.
The function is deactivated automatically when the passenger uses their temperature setting buttons.
It allows you: - in summer, to lower the temperature, - in winter, above 3 °C, to improve demisting.
Switching off
 Press the "A /C " button again to deactivate the air conditioning When the indicator lamp under the button is off, the air conditioning function is deactivated.
Switching on
 Press the "A/C" button to activate the air conditioning When the indicator lamp under the button is on, the air conditioning function is activated. The air conditioning cannot operate when the air flow is set to off.
Air conditioning On/Off
The air conditioning is designed to operate efficiently in all seasons, with the windows closed.
Ventilation with "ignition
on" function
With the ignition on, you can use the ventilation system and have access to the " Air conditioning " menu to adjust the air flow and air distribution in the passenger compartment. This function is available for a few minutes, depending on the state of charge of the battery of your vehicle.
This function does not activate the air conditioning. You can make use of the residual heat in the engine to warm the passenger compartment using the temperature setting buttons.

108
Driving
308_EN_CHAP04_CONDUITE_ED02-2013
Starting-switching off the engine, remote control
Put the gear lever into neutral.
A heavy object (key fob...), attached to the key and weighing down on its shaft in the ignition switch, could cause a malfunction.
Key left in the "Ignition on" position
On opening the driver's door, an alert message is displayed, accompanied by an audible signal, to remind you that the key is still in the ignition switch at position 1 (Stop) .
If the key has been left in the ignition switch at position 2 (Ignition on) , the ignition will be switched off automatically after one hour. To switch the ignition back on, turn the key to position 1 (Stop) , then back to position 2 (Ignition on) .
Ignition switch
1. Stop position. 2. Ignition on position. 3. Starting position.
Starting using the key
 Insert the key in the ignition switch. The system recognises the starting code.  Turn the key fully towards the dashboard to position 3 (Starting) .
 When the engine starts, release the key.
 Immobilise the vehicle.  Turn the key fully towards you to position 1 (Stop) .  Remove the key from the ignition switch.
Switching off using the key
Switching off the engine leads to a loss of braking assistance.