2014 NISSAN TEANA window

PWC-44
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER WINDOW MOTOR
Rear Power Window Motor LH Circuit Check
1. CHECK REAR POWER WINDOW SWITCH LH OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window motor LH.
3. Turn ignition switch ON.
4. Check voltage between rear power window motor LH connector D204 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect rear power window switch LH.
3. Check continuity between rear power window swit ch LH connector D203 and rear power window motor
LH connector D204.
4. Check continuity between rear power window switch LH connector D203 and ground.
Is the inspection result normal?
YES >> Check rear power window switch LH. Refer to PWC-44, "REAR LH : Component Inspection".
NO >> Repair or replace the harness or connectors.
3. CHECK REAR POWER WINDOW MOTOR LH
Check rear power window motor LH.
Refer to PWC-44, "REAR LH : Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace rear power window motor LH. Refer to GW-25, "Removal and Installation"
.
REAR LH : Component InspectionINFOID:0000000009460860
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW MOTOR LH
Check motor operation by connecting the battery voltage directly to rear power window motor LH D204.
Te r m i n a l
Window
condition Vo l ta g e
(Approx.)
(+)
(–)
Rear power window motor LH
connector Te r m i n a l
D204 1
Ground UP Battery voltage
DOWN 0
3 UP 0
DOWN Battery voltage
Rear power window switch LH connector Te r m i n a l
Rear power window motor LH
connector Terminal Continuity
D203 5
D204 1
Ye s
63
Rear power window switch LH connector Terminal GroundContinuity
D203 5
No
6
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER WINDOW MOTORPWC-45
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
Is the inspection result normal?
YES >> Rear power window motor LH is OK.
NO >> Replace rear power window motor LH. Refer to GW-25, "Removal and Installation"
.
REAR RH
REAR RH : DescriptionINFOID:0000000009460861
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or
rear power window switch RH.
REAR RH : Componen t Function CheckINFOID:0000000009460862
1. CHECK POWER WINDOW MOTOR CIRCUIT
Check rear power window motor RH operation with operat ing power window main switch or rear power win-
dow switch RH.
Is the inspection result normal?
YES >> Power window motor is OK.
NO >> Refer to PWC-45, "REAR RH : Diagnosis Procedure"
.
REAR RH : Diagnosis ProcedureINFOID:0000000009460863
Regarding Wiring Diagram information, refer to PWC-18, "Wiring Diagram - With Left Front Only Power Win-
dow Anti- Pinch".
Rear Power Window Motor RH Circuit Check
1. CHECK REAR POWER WINDOW SWITCH RH OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear power window motor RH.
3. Turn ignition switch ON.
4. Check voltage between rear power window motor RH connector D304 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect rear power window switch RH.
3. Check continuity between rear power window s witch RH connector D303 and rear power window motor
RH connector D304.
Te r m i n a l Motor condition
(+) (–)
31 DOWN
13 UP
Te r m i n a l Rear power window
switch RH condition Vol tag e
(Approx.)
(+)
(–)
Rear power window motor RH
connector Te r m i n a l
D304 1
Ground UP Battery voltage
DOWN 0
3 UP 0
DOWN Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-46
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER WINDOW MOTOR
4. Check continuity between rear power window switch RH connector D303 and ground.
Is the inspection result normal?
YES >> Check rear power window switch RH. Refer to PWC-46, "REAR RH : Component Inspection".
NO >> Repair or replace harness or connectors.
3. CHECK REAR POWER WINDOW MOTOR RH
Check rear power window motor RH.
Refer to PWC-46, "REAR RH : Component Inspection"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Replace rear power window motor RH. Refer to GW-25, "Removal and Installation"
.
REAR RH : Component InspectionINFOID:0000000009460864
COMPONENT INSPECTION
1. CHECK REAR POWER WINDOW MOTOR RH
Check motor operation by connecting the battery voltage directly to rear power window motor RH D304.
Is the inspection result normal?
YES >> Power window motor is OK.
NO >> Replace rear power window motor RH. Refer to GW-25, "Removal and Installation"
.
Rear power window switch RH
connector Te r m i n a l
Rear power window motor RH
connector Terminal Continuity
D303 5
D304 1
Ye s
63
Rear power window switch RH connector Terminal GroundContinuity
D303 5
No
6
Te r m i n a l Motor condition
(+) (–)
31 DOWN
13 UP
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENCODERPWC-47
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
ENCODER
DRIVER SIDE
DRIVER SIDE : DescriptionINFOID:0000000009460865
Detects condition of the front power window motor LH operation and transmits to main power window and door
lock/unlock switch as pulse signal.
DRIVER SIDE : Componen t Function CheckINFOID:0000000009460866
1. CHECK ENCODER OPERATION
Check front door glass LH perform AUTO open/close operation normally with main power window and door
lock/unlock switch.
Is the inspection result normal?
YES >> Encoder operation is OK.
NO >> Refer to PWC-47, "DRIVER SIDE : Diagnosis Procedure"
.
DRIVER SIDE : Diag nosis ProcedureINFOID:0000000009460867
Regarding Wiring Diagram information, refer to PWC-18, "Wiring Diagram - With Left Front Only Power Win-
dow Anti- Pinch".
Encoder Circuit Check
1. CHECK ENCODER OPERATION
1. Connect front power window motor LH.
2. Turn ignition switch ON.
3. Check signal between main power window and door lock/unlock switch connector D12 and ground with oscilloscope.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> GO TO 2.
2. CHECK FRONT POWER WINDOW MOTOR LH POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between front power window motor LH connector D9 and ground.
Te r m i n a l s
Signal
(Reference value)
(+)
(–)
Main power window and door lock/
unlock switch connector Te r m i n a l
D12 4
Ground Refer to following signal
5
AWKIA2032GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-48
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
ENCODER
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3. CHECK HARNESS CONTINUITY 1
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unl ock switch and front power window motor LH.
3. Check continuity between main power window and door lock/unlock switch connector D12 and front power window motor connector D9.
4. Check continuity between main power window and door lock/unlock switch connector D12 and ground.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-49, "DRIVER SIDE : Special Repair Requirement".
NO >> Repair or replace harness or connectors.
4. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front power window motor LH.
3. Check continuity between front power window motor LH connector D9 and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 5.
5. CHECK HARNESS CONTINUITY 2
1. Disconnect main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/unlock switch connector D12 and front
power window motor LH connector D9.
Is the inspection result normal?
YES >> Check main power window and door lock/unlock switch. Refer to PWC-33, "POWER WINDOW
MAIN SWITCH : Component Inspection".
NO >> Repair or replace the harness or connectors.
6. CHECK HARNESS CONTINUITY 3
1. Disconnect main power window and door lock/unlock switch.
Te r m i n a l
Vo l ta g e
(Approx.)
(+)
(–)
Front power window motor LH connector Terminal
D9 2 Ground 10
Main power window and door lock/unlock switch connector Te r m i n a lFront power window motor LH
connector Terminal Continuity
D12 14 D9 2 Yes
Main power window and door lock/unlock switch con- nector Te r m i n a l
GroundContinuity
D12 14 No
Front power window motor LH connector Terminal GroundContinuity
D9 4 Yes
Main power window and door lock/un- lock switch connector Te r m i n a lFront power window motor LH
connector Terminal Continuity
D12 12D94Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ENCODERPWC-49
< DTC/CIRCUIT DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
2. Check continuity between main power window D12 and door lock/unlock switch connector and front
power window motor LH connector D9.
3. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal?
YES >> Replace front power window motor LH. Refer to GW-16, "Removal and Installation - Front Regula-
tor". After that, refer to PWC-49, "DRIVER SIDE : Special Repair Requirement".
NO >> Repair or replace harness or connectors.
DRIVER SIDE : Special Repair RequirementINFOID:0000000009460868
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REPLACIN G CONTROL UNIT : Special Repair Require-
ment".
Is the inspection result normal?
YES >> Inspection end.
NO >> Check intermittent incident. Refer to GI-43, "Intermittent Incident"
.
Main power window and door lock/unlock
switch connector Te r m i n a lFront power window motor
LH connector Terminal Continuity
D12 4
D9 6
Ye s
55
Main power window and door lock/unlock switch connector Te r m i n a l
GroundContinuity
D12 4
No
5
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PWC-52
< DTC/CIRCUIT DIAGNOSIS >[LH FRONT ONLY ANTI-PINCH]
POWER WINDOW LOCK SWITCH
POWER WINDOW LOCK SWITCH
DescriptionINFOID:0000000009460873
Ground circuit of main power window and door lock/unlock
switch shuts off if power window lock switch of
main power window and door lock/unlock switch is operated. This inhibits all operation, except for the main
switch.
Component Function CheckINFOID:0000000009460874
1. CHECK POWER WINDOW LOCK SIGNAL
Exchanges for a normal main power window and door lock/unlock switch, and operation is checked.
Is the inspection result normal?
YES >> Replace main power window and door lock/unlock switch. Refer to PWC-65, "Removal and Instal-
lation". After that, refer to PWC-52, "Special Repair Requirement".
NO >> Check condition of harness and connector.
Special Repair RequirementINFOID:0000000009460875
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-27, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special
Repair Requirement".
Is the inspection result normal?
YES >> Inspection end.
NO >> Check intermittent incident. Refer to GI-43, "Intermittent Incident"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

POWER WINDOWS DO NOT OPERATE WITH ANY POWER WINDOW SWITCH-
ES
PWC-53
< SYMPTOM DIAGNOSIS > [LH FRONT ONLY ANTI-PINCH]
C
D E
F
G H
I
J
L
M A
B
PWC
N
O P
SYMPTOM DIAGNOSIS
POWER WINDOWS DO NOT OPERATE WITH ANY POWER WINDOW
SWITCHES
Diagnosis ProcedureINFOID:0000000009460876
1. CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Check BCM power supply and ground circuit.
Refer to BCS-74, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2. CHECK MAIN POWER WINDOW A ND DOOR LOCK/UNLOCK SWITCH
Check main power window and door lock/unlock switch.
Refer to PWC-33, "POWER WINDOW MAIN SWITCH : Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH POWER SUPPLY AND
GROUND CIRCUIT
Check main power window and door lock/unlock switch power supply and ground circuit.
Refer to PWC-30, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure"
.
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-43, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM