2014 NISSAN TEANA crank

WATER PUMPCO-45
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
4. Remove cowl top extension. Refer to
EXT-24, "Removal and Installation".
5. Remove the front road wheel and tire (RH). Refer to WT-55, "Adjustment"
.
6. Remove the fender protector (RH). Refer to EXT-26, "FENDER PROTECTOR : Removal and Installation"
.
7. Drain coolant from the radiator. Refer to CO-36, "Changing Engine Coolant"
.
CAUTION:
Perform when the engine is cold.
8. Disconnect coolant reservoir hose and remove coolant reservoir tank. Refer to CO-40, "Exploded View"
.
9. Drain the power steering fluid reservoir. Refer to ST-30, "Draining and Refilling"
.
10. Remove the power steering oil pump. Refer to ST-38, "Removal and Installation"
.
11. Support engine and remove the RH engine insulator and bracket. Refer to EM-220, "Exploded View"
.
12. Set No. 1 cylinder at TDC on its compression stroke. • Align pointer with TDC mark on crankshaft pulley.
13. Remove drive belt. Refer to EM-134, "Removal and Installation"
.
14. Remove the drive belt auto-tensioner assembly. Refer to EM-135, "Removal and Installation of Drive Belt
Auto-tensioner".
15. Remove water drain plug (A) and copper sealing washer (B) to drain coolant from engine.
CAUTION:
Do not reuse copper sealing washers.
16. Disconnect RH valve timing control connectors and remo ve valve timing control cover (bank 1). Refer to
EM-182, "Exploded View"
.
17. Remove water pump cover. Refer to CO-44, "Exploded View"
.
18. Remove the timing chain tensioner (primary) as follows:
a. Pull the lever (C) down to release the plunger stopper tab (B).
b. Insert the stopper pin A into the tensioner body hole to hold the lever (C) and keep the plunger stopper tab (B) released.
NOTE:
An allen wrench [(1.2 mm (0.047 in)] is used for a stopper pin A
as an example.
c. Compress the plunger (D) into the tensioner body (1) by press- ing the slack guide (2).
d. Keep the slack guide (2) pressed and lock the plunger (D) in by pushing the stopper pin A through the lever (C) and into the
chain tensioner body hole.
e. Remove timing chain tensioner bolts and then remove the timing chain tensioner. CAUTION:
Be careful not to drop timing chain te nsioner bolts inside timing chain case.
19. Remove the three water pump bolts (A). Make a gap between water pump sprocket (1) and timing chain, by carefully turning
crankshaft pulley (2) counterclockwise until timing chain loosens
on water pump sprocket (1).
: Front
AWBIA1202GB
AWBIA0903ZZ
AWBIA0904ZZ
Revision: November 20132014 Altima NAM

WATER PUMPCO-47
< REMOVAL AND INSTALLATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
CO
NP
O
4. Turn the crankshaft pulley approximately 20
° clockwise so that
the timing chain on the timing chain tensioner side is loose.
5. Apply engine oil to the oil feed hole and timing chain tensioner and install the timing chain tensioner.
6. Remove the stopper pin (A).
7. Install valve timing control cover (bank 1) and water pump cover.
a. Before installing, remove all traces of liquid gasket from mating surface of water pump cover and IVT cover using a scraper.
Also remove traces of liquid gasket from the mating surface of the front cover.
b. Apply a continuous bead of liquid gasket to mating surface of IVT cover and water pump cover. Use Gen-
uine RTV Silicone Sealant or equivalent. Refer to GI-21, "Recommended Chemical Products and
Sealants".
CAUTION:
• Installation should be done within 5 minutes afte r applying liquid gasket.
• Do not fill the engine with oil for at least 30 minutes after the co mponents are installed to allow
the sealant to cure.
8. Install water drain plug (A) and copper sealing washer (B). CAUTION:
Do not reuse copper sealing washers.
9. Installation of remaining components is in the reverse order of removal. • After installation, refill coolant and check for leaks. Refer to CO-36, "Changing Engine Coolant"
and CO-
35, "System Inspection".
CAUTION:
Do not spill coolant in en gine compartment. Use a sh op cloth to absorb coolant.
• After starting engine, let idle for three minutes, then rev engine up to 3,000 rpm under no load to purge air from the high-pressure chamber of the chai n tensioner. The engine may produce a rattling noise.
This indicates that air still remains in the chamber and is not a matter of concern.
INSPECTION AFTER INSTALLATION
• Before starting engine, check oil/fluid levels incl uding engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-11, "FOR USA AND CANADA : Fluids and Lubricants"
.
PBIC0848E
AWBIA0905ZZ
: Front
Water drain plug (A) : Refer to EM-224, "Disas-
sembly and Assembly".
AWBIA1202GB
Revision: November 20132014 Altima NAM

DLK-44
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
* : Initial setting
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)INFOID:0000000009952502
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF → ON (for at least 5 seconds) → OFF. If this step is not performed, the BCM may not go
to ”sleep mode”, potentially causing a di scharged battery and a no-start condition.
SELF DIAGNOSTIC RESULT
Refer to BCS-52, "DTC Index".
DATA MONITOR
AUTO LOCK FUNCTION MODE3 This mode is not used.
MODE2 Doors lock automatically when shifted out of P (park).
MODE1* Doors lock automatically when vehicle speed reaches 24 km/h (15 mph).
Off —
AUTO UNLOCK FUNCTION MODE3 This mode is not used.
MODE2 Doors unlock automatically when shifted into P (park).
MODE1* Doors unlock automatically when ignition is switched from ON to OFF.
Off —
Support Item Setting Description
Monitor Item [Unit] Main Description
REQ SW -DR [On/Off] ×Indicates condition of door request switch LH.
REQ SW -AS [On/Off] ×Indicates condition of door request switch RH.
REQ SW -BD/TR [On/Off] ×Indicates condition of trunk opener request switch.
PUSH SW [On/Off] Indicates condition of push-button ignition switch.
SHFTLCK SLNID PER SPLY [On/Off] ×Indicates condition of power supply to shiftlock solenoid.
BRAKE SW 1 [On/Off] ×Indicates condition of brake switch.
BRAKE SW 2 [On/Off] Indicates condition of brake switch.
DETE/CANCL SW [On/Off] ×Indicates condition of P (park) position.
SFT PN/N SW [On/Off] ×Indicates condition of P (park) or N (neutral) position.
UNLK SEN -DR [On/Off] ×Indicates condition of door unlock sensor.
PUSH SW -IPDM [On/Off] Indicates condition of push-button ignition switch received from IPDM E/R
on CAN communication line.
IGN RLY1 -F/B [On/Off] Indicates condition of ignition relay 1 received from IPDM E/R on CAN
communication line.
DETE SW -IPDM [On/Off] Indicates condition of detent switch received from TCM on CAN communi-
cation line.
SFT PN -IPDM [On/Off] Indicates condition of P (park) or N (neutral) position from TCM on CAN
communication line.
SFT P -MET [On/Off] Indicates condition of P (park) position from TCM on CAN communication
line.
SFT N -MET [On/Off] Indicates condition of N (neutral) position from IPDM E/R on CAN commu-
nication line.
ENGINE STATE [STOP/START/CRANK/RUN] ×Indicates condition of engine state from ECM on CAN communication line.
VEH SPEED 1 [mph/km/h] ×Indicates condition of vehicle speed signal received from ABS on CAN
communication line.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DIAGNOSIS SYSTEM (BCM)DLK-45
< SYSTEM DESCRIPTION >
C
D E
F
G H
I
J
L
M A
B
DLK
N
O P
ACTIVE TEST
VEH SPEED 2 [mph/km/h] ×Indicates condition of vehicle speed signal received from combination
meter on CAN communication line.
DOOR STAT -DR [LOCK/READY/UNLK] ×Indicates condition of driver side door status.
DOOR STAT -AS [LOCK/READY/UNLK] ×Indicates condition of passenger side door status.
DOOR STAT -RR [LOCK/READY/UNLK] ×Indicates condition of rear right side door status.
DOOR STAT -RL [LOCK/READY/UNLK] ×Indicates condition of rear left side door status.
ID OK FLAG [Set/Reset] Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset] Indicates condition of engine start possibility.
PRMT RKE STRT [Set/Reset] Indicates condition of engine start possibility from Intelligent Key.
I-KEY OK FLAG [Key ON/Key OFF] ×Indicates condition of Intelligent Key OK flag.
PRBT ENG STRT [Set/Reset] Indicates condition of engine start prohibit.
ID AUTHENT CANCEL TIMER [STOP] Indicates condition of Intelligent Key ID authentication.
ACC BATTERY SAVER [STOP] Indicate s condition of battery saver.
CRNK PRBT TMR [On/Off] In dicates condition of crank prohibit timer.
AUT CRNK TMR [On/Off] Indicates condition of automatic engine crank timer from Intelligent Key.
CRNK PRBT TME [sec] I ndicates condition of engine crank prohibit time.
AUTO CRNK TME [sec] Indicates co ndition of automatic engine crank time from Intelligent Key.
CRANKING TME [sec] Indicates condition of engine cranking time from Intelligent Key.
DETE SW PWR [On/Off] Indicates condition of detent switch voltage.
ACC RLY -REQ [On/Off] Indicates condition of accessory relay control request.
RKE OPE COUN1 [0-19] ×When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
RKE OPE COUN2 [0-19] ×When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
TRNK/HAT MNTR [On/Off] Indicates condition of trunk room lamp switch.
RKE-LOCK [On/Off] Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off] Indicates condition of unlock signal from Intelligent Key.
RKE-TR/BD [On/Off] Indicates condition of trunk open signal from Intelligent Key.
RKE-PANIC [On/Off] Indicates condition of panic signal from Intelligent Key.
RKE-MODE CHG [On/Off] Indicates condition of mode change signal from Intelligent Key. Monitor Item [Unit] Main Description
Test Item Description
INTELLIGENT KEY LINK (CAN) This test is able to check Intelligent Key iden
tification number [Off/ID No1/ID N02/ID No3/ID
No4/ID No5].
INT LAMP This test is able to check interior room lamp operation [On/Off].
FLASHER This test is able to check hazard lamp operation [LH/RH/Off].
HORN This test is able to check horn operation [On].
BATTERY SAVER This test is able to check battery saver operation [On/Off].
TRUNK/BACK DOOR This test is able to check trunk actuator operation [Open].
OUTSIDE BUZZER This test is able to check In telligent Key warning buzzer operation [On/Off].
INSIDE BUZZER This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
INDICATOR This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
IGN CONT2 This test is able to check ignition relay-2 control operation [On/Off].
ENGINE SW ILLUMI This test is able to check push-bu tton ignition switch START indicator operation [On/Off].
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DLK-46
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
PUSH SWITCH INDICATOR This test is able to check push-button ignition switch indicator operation [On/Off].
ACC CONT This test is able to check accessory relay control operation [On/Off].
IGN CONT1 This test is able to check ignition relay-1 control operation [On/Off].
ST CONT LOW This test is able to check starter control relay operation [On/Off].
IGNITION RELAY This test is able to ignition relay operation [On/Off].
REVERSE LAMP TEST This test is able to check reverse lamp illumination operation [On/Off].
TRUNK/LUGGAGE LAMP TEST This test is able to check cargo lamp illumination operation [On/Off].
KEYFOB PW TEST This test is able to check power wind ow operation using the Intelligent Key [Off/DOWN/UP].
SHIFTLOCK SOLENOID TEST This test is able to check shift lock solenoid operation [On/Off]. Test Item Description
Support Item Setting Description
IGN/ACC BATTERY SAVER On* Battery saver function ON.
Off Battery saver function OFF.
REMOTE ENGINE STARTER On* Remote engine start function ON.
Off Remote engine start function OFF.
ANSWERBACK I-KEY LOCK UNLOCK BUZZER Buzzer reminder function by door lock/unlock request switch ON.
HORN Horn chirp reminder function by door lock request switch ON.
Off* No reminder function by door lock/unlock request switch.
INVALID This mode is not used.
ANSWERBACK KEYLESS LOCK UN-
LOCK On
Buzzer or horn chirp reminder when doors are locked/unlocked with
Intelligent Key.
Off* No buzzer or horn chirp reminder when doors are locked/unlocked
with Intelligent Key.
ANSWER BACK On* Horn chirp reminder when doors are locked with Intelligent Key.
Off No horn chirp reminder when doors are locked with Intelligent Key.
RETRACTABLE MIRROR SET On Retractable mirror set ON.
Off* Retractable mirror set OFF.
CONFIRM KEY FOB ID — Intelligent Key ID code can check.
LOCK/UNLOCK BY I-KEY On* Door lock/unlock function from Intelligent Key ON.
Off Door lock/unlock function from Intelligent Key OFF.
ENGINE START BY I-KEY On* Engine start function from Intelligent Key ON.
Off Engine start function from Intelligent Key OFF.
TRUNK/GLASS HATCH OPEN On* Buzzer reminder function by trunk opener request switch ON.
Off Buzzer reminder function by trunk opener request switch OFF.
INTELLIGENT KEY LINK SET On Intelligent Key link set ON.
Off* Intelligent Key link set OFF.
SHORT CRANKING OUTPUT Start70 msec
Starter motor operation duration times.
100 msec
200 msec
End —
INSIDE ANT DIAGNOSIS — This function allows inside key antenna self-diagnosis.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-1
ENGINE
C
D E
F
G H
I
J
K L
M
SECTION EC
A
EC
N
O P
CONTENTS
ENGINE CONTROL SYSTEM
QR25DE
PRECAUTION ................ ..............................
15
PRECAUTIONS .............................................. ....15
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ....
15
Precaution for Procedure without Cowl Top Cover ....15
On Board Diagnostic (OBD) System of Engine
and CVT .............................................................. ....
15
General Precautions ...............................................16
PREPARATION ...........................................19
PREPARATION .............................................. ....19
Special Service Tools .......................................... ....19
Commercial Service Tools ......................................19
SYSTEM DESCRIPTION .............................21
COMPONENT PARTS ................................... ....21
Component Parts Location ................................ ....21
ECM ........................................................................25
Accelerator Pedal Position Sensor ...................... ....25
Electric Throttle Control Actuator ........................ ....25
Ignition Coil With Power Transistor .........................26
Fuel Injector ........................................................ ....26
Fuel Level Sensor Unit and Fuel Pump .............. ....26
Fuel Tank Temperature Sensor .......................... ....27
Mass Air Flow Sensor (With Intake Air Tempera-
ture Sensor) ........................................................ ....
27
Manifold Absolute Pressure Sensor ........................28
Engine Coolant Temperature Sensor .................. ....28
Crankshaft Position Sensor (POS) ..........................29
Camshaft Position Sens or (PHASE) .......................29
Intake Valve Timing Cont rol Solenoid Valve ...........30
Intake Valve Timing Intermediate Lock Control
Solenoid Valve .................................................... ....
30
Exhaust Valve Timing Control Position Sensor .......30
Exhaust Valve Timing Control Solenoid Valve ........31
Intake Manifold Runner Control Valve ................. ....31
Intake Manifold Tuning Valve ..................................31
Air Fuel Ratio (A/F) Sensor 1 ..................................32
Heated Oxygen Sensor 2 ........................................32
Knock Sensor ..........................................................33
Engine Oil Pressure Sensor ....................................33
Engine Oil Temperature Sensor .......................... ....33
Cooling Fan .............................................................34
EVAP Canister .........................................................34
EVAP Canister Purge Volu me Control Solenoid
Valve .................................................................... ....
34
EVAP Canister Vent Control Valve ..........................35
EVAP Control System Pres sure Sensor ..................35
Battery Current Sensor (With Battery Tempera-
ture Sensor) ......................................................... ....
35
Malfunction Indicator lamp (MIL) .............................36
Oil Pressure Warning Lamp ....................................36
Refrigerant Pressure Sensor ............................... ....36
Stop Lamp Switch & Brake Pedal Position Switch ....36
ASCD Steering Switch .............................................37
Information Display ..................................................37
STRUCTURE AND OPERATION .....................38
Positive Crankcase Ventilation ................................38
On Board Refueling Vapor Recovery (ORVR) ........39
SYSTEM ............................................................40
ENGINE CONTROL SYSTEM ........................ ...........40
ENGINE CONTROL SYSTEM : System Descrip-
tion ....................................................................... ....
40
ENGINE CONTROL SYSTEM : Fail Safe ..............41
MULTIPORT FUEL INJECTION SYSTEM ................43
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description (with auto matic air conditioner) ......
43
MULTIPORT FUEL INJECTION SYSTEM : Sys-
tem Description (with manual air conditioner) .........
46
ELECTRIC IGNITION SYSTEM .................................48
ELECTRIC IGNITION SYSTEM : System De-
scription ............................................................... ....
48
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-4
DTC Logic ..............................................................255
Diagnosis Procedure .............................................256
Component Inspection ...........................................256
P0130 A/F SENSOR 1 .....................................258
DTC Logic ............................................................ ..258
Component Function Check ..................................259
Diagnosis Procedure .............................................259
P0131 A/F SENSOR 1 .....................................262
DTC Logic ............................................................ ..262
Diagnosis Procedure .............................................263
P0132 A/F SENSOR 1 .....................................265
DTC Logic ............................................................ ..265
Diagnosis Procedure .............................................266
P0137 HO2S2 ..................................................268
DTC Logic ............................................................ ..268
Component Function Check ..................................269
Diagnosis Procedure .............................................270
Component Inspection ...........................................271
P0138 HO2S2 ..................................................274
DTC Logic ............................................................ ..274
Component Function Check ..................................275
Diagnosis Procedure .............................................276
Component Inspection ...........................................279
P0139 HO2S2 ..................................................282
DTC Logic ............................................................ ..282
Component Function Check ..................................283
Diagnosis Procedure .............................................284
Component Inspection ...........................................286
P014C, P014D, P015A, P015B, A/F SENSOR
1 ...................................................................... .
289
DTC Logic ............................................................ ..289
Diagnosis Procedure .............................................291
P0171 FUEL INJECTION SYSTEM FUNC-
TION ................................................................ .
294
DTC Logic ............................................................ ..294
Diagnosis Procedure .............................................295
P0172 FUEL INJECTION SYSTEM FUNC-
TION ................................................................ .
298
DTC Logic ............................................................ ..298
Diagnosis Procedure .............................................299
P0181 FTT SENSOR .......................................302
DTC Logic ............................................................ ..302
Component Function Check ..................................303
Diagnosis Procedure .............................................304
Component Inspection ...........................................305
P0182, P0183 FTT SENSOR ...........................306
DTC Logic ............................................................ ..306
Diagnosis Procedure .............................................306
Component Inspection ...........................................307
P0196 EOT SENSOR .......................................309
DTC Logic ............................................................ .309
Component Function Check .................................311
Diagnosis Procedure .............................................311
Component Inspection ..........................................311
P0197, P0198 EOT SENSOR ...........................312
DTC Logic ............................................................ .312
Diagnosis Procedure .............................................312
Component Inspection ..........................................313
P0222, P0223 TP SENSOR ..............................315
DTC Logic ............................................................ .315
Diagnosis Procedure .............................................315
Component Inspection ..........................................317
P0300, P0301, P0302, P0303, P0304 MIS-
FIRE ................................................................ ..
318
DTC Logic ............................................................ .318
Diagnosis Procedure .............................................319
P0327, P0328 KS .............................................324
DTC Logic ............................................................ .324
Diagnosis Procedure .............................................324
Component Inspection ..........................................325
P0335 CKP SENSOR (POS) ............................326
DTC Logic ............................................................ .326
Diagnosis Procedure .............................................326
Component Inspection (Crankshaft Position sen-
sor) ....................................................................... .
328
P0340 CMP SENSOR (PHASE) .......................329
DTC Logic ............................................................ .329
Diagnosis Procedure .............................................329
Component Inspection (Camshaft position sen-
sor) ....................................................................... .
331
P0420 THREE WAY CATALYST FUNCTION ..332
DTC Logic ............................................................ .332
Component Function Check .................................333
Diagnosis Procedure .............................................334
P0441 EVAP CONTROL SYSTEM ..................337
DTC Logic ............................................................ .337
Component Function Check .................................338
Diagnosis Procedure .............................................339
P0443 EVAP CANISTER PURGE VOLUME
CONTROL SOLENOID VALVE ...................... ..
342
DTC Logic ............................................................ .342
Diagnosis Procedure .............................................343
Component Inspection ..........................................345
P0444, P0445 EVAP CANISTER PURGE
VOLUME CONTROL SO LENOID VALVE .......
347
DTC Logic ............................................................ .347
Diagnosis Procedure .............................................347
Component Inspection ..........................................349
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-5
C
D E
F
G H
I
J
K L
M
EC A
N
O P
P0447 EVAP CANISTER VENT CONTROL
VALVE ............................................................ ..
350
DTC Logic ........................................................... ..350
Diagnosis Procedure .............................................350
Component Inspection ..........................................352
P0448 EVAP CANISTER VENT CONTROL
VALVE ............................................................ ..
354
DTC Logic ........................................................... ..354
Diagnosis Procedure .............................................355
Component Inspection ..........................................356
P0451 EVAP CONTROL SYSTEM PRES-
SURE SENSOR .............................................. ..
358
DTC Logic ........................................................... ..358
Diagnosis Procedure .............................................359
Component Inspection ..........................................361
P0452 EVAP CONTROL SYSTEM PRES-
SURE SENSOR .............................................. ..
362
DTC Logic ........................................................... ..362
Diagnosis Procedure .............................................363
Component Inspection ..........................................364
P0453 EVAP CONTROL SYSTEM PRES-
SURE SENSOR .............................................. ..
366
DTC Logic ........................................................... ..366
Diagnosis Procedure .............................................367
Component Inspection ..........................................369
P0456 EVAP CONTROL SYSTEM ..................370
DTC Logic ........................................................... ..370
Diagnosis Procedure .............................................371
Component Inspection ..........................................375
P0460 FUEL LEVEL SENSOR ........................376
DTC Logic ........................................................... ..376
Diagnosis Procedure .............................................376
P0461 FUEL LEVEL SENSOR ........................377
DTC Logic ........................................................... ..377
Component Function Check ..................................377
Diagnosis Procedure .............................................378
P0462, P0463 FUEL LEVEL SENSOR ............379
DTC Logic ........................................................... ..379
Diagnosis Procedure .............................................379
P0500 VSS .......................................................380
Description .......................................................... ..380
DTC Logic .............................................................380
Diagnosis Procedure .............................................380
P0506 ISC SYSTEM .........................................382
Description .......................................................... ..382
DTC Logic .............................................................382
Diagnosis Procedure .............................................382
P0507 ISC SYSTEM .........................................384
Description .......................................................... ..384
DTC Logic .............................................................384
Diagnosis Procedure ........................................... ..384
P050A, P050B, P050E COLD START CON-
TROL ...............................................................
386
Description ........................................................... ..386
DTC Logic ..............................................................386
Diagnosis Procedure .............................................387
P0520 EOP SENSOR ......................................388
DTC Logic ..............................................................388
Diagnosis Procedure .............................................388
Component Inspection ...........................................390
P0524 ENGINE OIL PRESSURE ....................391
DTC Logic ..............................................................391
Diagnosis Procedure .............................................392
Component Inspection ...........................................393
P052A, P052B INTAKE VALVE TIMING CON-
TROL ...............................................................
394
DTC Logic ............................................................ ..394
Diagnosis Procedure .............................................394
Component Inspection (Intake Valve Timing Con-
trol Solenoid Valve) ............................................. ..
396
Component Inspection (Intake Valve Timing Inter-
mediate Lock Control Solenoid Valve) ................ ..
397
Component Inspection (Crankshaft Position sen-
sor) ...................................................................... ..
397
Component Inspection (Camshaft position sen-
sor) ...................................................................... ..
398
P0603 ECM .....................................................400
DTC Logic ..............................................................400
Diagnosis Procedure .............................................400
P0604 ECM .....................................................401
DTC Logic ..............................................................401
Diagnosis Procedure .............................................401
P0605 ECM .....................................................402
DTC Logic ..............................................................402
Diagnosis Procedure .............................................402
P0606 ECM .....................................................403
DTC Logic ..............................................................403
Diagnosis Procedure .............................................403
P0607 ECM .....................................................404
DTC Logic ..............................................................404
Diagnosis Procedure .............................................404
P060A ECM .....................................................405
DTC Logic ..............................................................405
Diagnosis Procedure .............................................405
P060B ECM .....................................................406
DTC Logic ..............................................................406
Diagnosis Procedure .............................................406
P0643 SENSOR POWER SUPPLY ................407
Description .............................................................407
DTC Logic ..............................................................407
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM