2014 NISSAN TEANA Pressure

BCS
BCM (BODY CONTROL MODULE)BCS-35
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
TAIL LAMP SW
Other than lighting switch 1ST and 2ND Off
Lighting switch 1ST or 2ND On
TP 4 The ID of fourth key is not registered to BCM Yet
The ID of fourth key is registered to BCM DONE
TP 3 The ID of third key is not registered to BCM Yet
The ID of third key is registered to BCM DONE
TP 2 The ID of second key is not registered to BCM Yet
The ID of second key is registered to BCM DONE
TP 1 The ID of first key is not registered to BCM Yet
The ID of first key is registered to BCM DONE
TR CANCEL SW Trunk lid opener cancel switch OFF Off
Trunk lid opener cancel switch ON On
TR/BD OPEN SW Trunk opener switch OFF Off
While the trunk opener switch is turned ON On
TRNK/HAT MNTR Trunk lid closed Off
Trunk lid opened On
TURN SIGNAL L Turn signal switch OFF Off
Turn signal switch LH On
TURN SIGNAL R Turn signal switch OFF Off
Turn signal switch RH On
UNLK SEN-DR Driver door UNLOCK status Off
Driver door LOCK status On
VEH SPEED 1 While driving, equivalent to speedometer reading mph, km/h
VEH SPEED 2 While driving, equivalent to speedometer reading mph, km/h
WARNING LAMP Low tire pressure wa
rning lamp in combination meter OFF Off
Low tire pressure warning la mp in combination meter ON On
Monitor Item Condition Value/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-52
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000009462019
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- tion switch OFF → ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it . It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
5 • C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
• C1730: FLAT TIRE FL
• C1731: FLAT TIRE FR
• C1732: FLAT TIRE RR
• C1733: FLAT TIRE RL
• C1734: CONTROL UNIT
• C1735: IGNITION SIGNAL
6 • B2621: INSIDE ANTENNA
• B2622: INSIDE ANTENNA
7 B259A: ROOM LAMP FUSE
Priority DTC
CONSULT display Fail-safe
Intelligent Key
warning lamp ON Tire pressure
monitor warning lamp ON Reference page
No DTC is detected.
Further testing may be required. —— — —
U1000: CAN COMM CIRCUIT — — — BCS-68, "Description"
U1010: CONTROL UNIT (CAN) — — — BCS-69, "DTC Logic"
U0415: VEHICLE SPEED SIG — — —BCS-70, "Description"
B2190: NATS ANTENNA AMP×—— SEC-84, "Description"
B2191: DIFFERENCE OF KEY ×—— SEC-86, "Description"
B2192: ID DISCORD BCM-ECM ×—— SEC-87, "DTC Logic"
B2193: CHAIN OF BCM-ECM ×—— SEC-88, "DTC Logic"
B2195: ANTI SCANNING ×—— SEC-89, "DTC Logic"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-53
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
B2196: DONGLE UNIT — — —
SEC-90, "Description"
B2198: NATS ANTENNA AMP. — — — SEC-92, "DTC Logic"
B2555: STOP LAMP — — —SEC-94, "DTC Logic"
B2556: PUSH-BTN IGN SW —×— SEC-97, "DTC Logic"
B2557: VEHICLE SPEED — ×— SEC-99, "DTC Logic"
B2560: STARTER CONT RELAY ××—SEC-100, "Description"
B2562: LOW VOLTAGE ×—— BCS-71, "DTC Logic"
B259A: ROOM LAMP FUSE — — — BCS-72, "DTC Logic"
B2601: SHIFT POSITION —×—SEC-101, "DTC Logic"
B2602: SHIFT POSITION — ×—SEC-104, "DTC Logic"
B2603: SHIFT POSI STATUS — ×—SEC-106, "DTC Logic"
B2604: PNP SW — ×—SEC-110, "DTC Logic"
B2605: PNP SW — ×—SEC-113, "DTC Logic"
B2608: STARTER RELAY ××—SEC-116, "DTC Logic"
B260A: IGNITION RELAY ××—PCS-58, "DTC Logic"
B2614: ACC RELAY CIRC — ×— PCS-60, "DTC Logic"
B2615: BLOWER RELAY CIRC — ×— PCS-62, "DTC Logic"
B2616: IGN RELAY CIRC — ×— PCS-64, "DTC Logic"
B2617: STARTER RELAY CIRC ××—SEC-118, "Description"
B2618: BCM ××—PCS-66, "DTC Logic"
B261A: PUSH-BTN IGN SW — ×— PCS-68, "DTC Logic"
B261B: RES ENG RUN — — — DLK-87, "DTC Logic"
B261E: VEHICLE TYPE××
(Turn ON for
15 seconds) —
SEC-120, "Description"
B2621: INSIDE ANTENNA — — — DLK-88, "DTC Logic"
B2622: INSIDE ANTENNA — — —DLK-90, "DTC Logic"
B26F1: IGNITION RELAY — — —PCS-70, "DTC Logic"
B26F2: IGNITION RELAY — — —PCS-72, "DTC Logic"
B26F6: BCM — — —PCS-74, "DTC Logic"
B26FD: SHIFT LOCK SOLENOID — — — DLK-92, "DTC Logic"
B26FE: HOOD SWITCH — — —DLK-95, "DTC Logic"
B26FF: REMOTE KEYLESS ENTRY RE-
CEIVER —— —
DLK-97, "DTC Logic"
C1704: LOW PRESSURE FL — — ×
WT-28, "DTC Logic"
C1705: LOW PRESSURE FR — — ×
C1706: LOW PRESSURE RR — — ×
C1707: LOW PRESSURE RL — — ×
C1708: [NO DATA] FL — — ×
WT-30, "DTC Logic"
C1709: [NO DATA] FR — — ×
C1710: [NO DATA] RR — — ×
C1711: [NO DATA] RL — — ×
CONSULT display Fail-safe
Intelligent Key
warning lamp
ON Tire pressure
monitor warning
lamp ON Reference page
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-54
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
C1712: [CHECKSUM ERR] FL — —
×
WT-33, "DTC Logic"
C1713: [CHECKSUM ERR] FR — — ×
C1714: [CHECKSUM ERR] RR — — ×
C1715: [CHECKSUM ERR] RL — — ×
C1716: [PRESSDATA ERR] FL — — ×
WT-35, "DTC Logic"
C1717: [PRESSDATA ERR] FR — — ×
C1718: [PRESSDATA ERR] RR — — ×
C1719: [PRESSDATA ERR] RL — — ×
C1720: [CODE ERR] FL — — ×
WT-37, "DTC Logic"
C1721: [CODE ERR] FR — — ×
C1722: [CODE ERR] RR — — ×
C1723: [CODE ERR] RL — — ×
C1724: [BATT VOLT LOW] FL — — ×
WT-39, "DTC Logic"
C1725: [BATT VOLT LOW] FR — — ×
C1726: [BATT VOLT LOW] RR — — ×
C1727: [BATT VOLT LOW] RL — — ×
C1729: VHCL SPEED SIG ERR — — ×WT-41, "DTC Logic"
C1730: FLAT TIRE FL — — ×
WT-42, "DTC Logic"
C1731: FLAT TIRE FR — — ×
C1732: FLAT TIRE RR — — ×
C1733: FLAT TIRE RL — — ×
C1734: CONTROL UNIT — — ×WT-44, "DTC Logic"
C1735: IGNTION SIGNAL — — ×WT-46, "DTC Logic"
CONSULT display Fail-safe Intelligent Key
warning lamp
ON Tire pressure
monitor warning
lamp ON Reference page
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-66
< BASIC INSPECTION >[BCM]
INSPECTION AND ADJUSTMENT
CONFIGURATION (BCM) : Configuration list
INFOID:0000000009462025
CAUTION:
Thoroughly read and understand the vehicle specifi cation. Incorrect settings may result in abnormal
control of ECU.
⇔ : Items which confirm vehicle specifications MANUAL SETTING ITEM
Items Setting value
AUTO LIGHT WITHOUT ⇔ MODE1 ⇔ MODE2 ⇔ MODE3 ⇔ MODE4 ⇔ MODE5
FR FOG LAMP WITHOUT ⇔ MODE1 ⇔ MODE2
TIRE PRESSURE 220kPa ⇔ 230kPa ⇔ 240kPa
BCM AC CONTROL MODE1 ⇔ MODE2
Key Fob Type ENST/LCK/UNLCK/ALRM
⇔ ENST/LCK/UNLCK/BD/ALRM ⇔
ENST/LCK/UNLCK/TRK/ALRM ⇔ LCK/UNLCK/PBD/ALRM ⇔
LCK/UNLCK/ALRM ⇔ LCK/UNLCK/PBD ⇔ LCK/UNLCK/TRNK ⇔
LCK/UNLCK ⇔ LCK/UNLCK/TRNK/ALRM
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BR-10
< BASIC INSPECTION >
BRAKE BOOSTER
BRAKE BOOSTER
InspectionINFOID:0000000009463686
OPERATION
Depress the brake pedal several times at five second intervals with
the engine stopped. Start the engine with the brake pedal fully
depressed. Check that the cl earance between brake pedal and dash
lower panel decreases.
NOTE:
A slight impact with a small click may be felt on the pedal when the
brake pedal is fully depressed. Th is is normal brake system opera-
tion.
VACUUM INSPECTION
Idle the engine for one minute to apply vacuum to the brake booster.
Stop the engine. Depress the brake pedal several times at five sec-
ond intervals until the accumulated vacuum is released to atmo-
spheric pressure. Check that the clearance between brake pedal
and dash lower panel gradually increases (A → B → C) each time
the brake pedal is depressed during this operation.
Depress the brake pedal with the engine running. Then stop the
engine while holding down the brake pedal. Check that the brake
pedal stroke does not change after holding down the brake pedal for
30 seconds or more.
NOTE:
A slight impact with a small click may be felt on the pedal when the
brake pedal is fully depressed. Th is is normal brake system opera-
tion.
BRA0037D
JPFIA0043ZZ
JPFIA0044ZZ
Revision: November 20132014 Altima NAM

BR-28
< REMOVAL AND INSTALLATION >
BRAKE BOOSTER
BRAKE BOOSTER
Exploded ViewINFOID:0000000009463706
Removal and Installation - QR25DEINFOID:0000000009463707
CAUTION:
• Do not deform or bend brake tube whil e removing and installing brake booster.
• Do not reuse snap pin or clevis pin.
• Do not reuse brake booster gasket.
• Do not damage brake booster stud bolt threads. If brake booster is tilted during service, the dash
panel may damage the threads.
REMOVAL
1. Release the fuel pressure from the fuel system. Refer to EC-182, "Work Procedure".
2. Disconnect the battery negative terminal. Refer to PG-73, "Removal and Installation (Battery)"
.
3. Remove the instrument lower panel LH. Refer to IP-21, "Removal and Installation"
.
4. Disconnect the harness connector from the accelerator pedal assembly.
1. Master cylinder assembly 2. O-ring 3. Brake booster
4. Gasket A. Refer to BR-26, "Removal and
Installation".B. Master cylinder assembly nut
C. Clevis lock nut
ALFIA0318ZZ
Revision: November 20132014 Altima NAM

BRAKE BOOSTERBR-29
< REMOVAL AND INSTALLATION >
C
D E
G H
I
J
K L
M A
B
BR
N
O P
5. Remove the snap pin (1) and clevis pin (2) from the brake pedal. CAUTION:
Do not reuse snap pin or clevis pin.
6. Disconnect the harness connectors from the ASCD cancel switch and stop lamp switch.
7. Disconnect the steering column assembly pinch bolt and position the steering column shaft aside. Refer to
ST-33, "Exploded View"
.
8. Remove the brake master cylinder. Refer to BR-26, "Removal and Installation"
.
9. Disconnect the fuel line main connections. Refer to FL-5, "Quick Connector"
.
10. Remove the cowl top. Refer to EXT-24, "Removal and Installation"
.
11. Remove the strut tower bar. Refer to FSU-19, "Exploded View"
.
12. Remove the wiper drive assembly. Refer to WW-64, "Removal and Installation"
.
13. Remove the cowl top extension.
14. Disconnect the vacuum hose from the brake booster.
15. Disconnect the active boost sensor harness connector.
16. Remove brake booster nuts.
17. Remove the brake booster.
18. Remove and discard the brake booster gasket. CAUTION:
Do not reuse brake booster gasket.
INSTALLATION
Installation is in the reverse order of removal.
• Prior to installation, loosen clevis lock nut (1) and adjust input rod (2) to the specified value (B).
• After input rod adjustment (B), temporarily tighten clevis lock nut for installation of brake booster.
• Connect the battery negative terminal. Refer to PG-7, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement".
Removal and Installation - VQ35DEINFOID:0000000009463708
CAUTION:
• Do not deform or bend brake tube while removing and installing brake booster.
• Do not reuse snap pin or clevis pin.
• Do not reuse brake booster gasket.
• Do not damage brake booster stud bolt threads. If brake booster is tilted during service, the dash
panel may damage the threads.
REMOVAL
1. Release the fuel pressure from the fuel system. Refer to EC-687, "Work Procedure".
JPFIA0019ZZ
Length (B) : Refer to BR-49, "Brake Booster".
ALFIA0299ZZ
Revision: November 20132014 Altima NAM