2014 MITSUBISHI OUTLANDER SPORT service

Electronic immobilizer (An
ti-theft starting system)
Locking and unlocking 4-3
4
E00300202996
The electronic immobilizer is designed toreduce significantly the possibility of vehicletheft. The purpose of the system is to immo-bilize the vehicle if an invalid start isattempted. A valid start attempt can only beachieved by using a key “registered” to theimmobilizer system.
E00300303721
Press the remote control switch, and all doorsand the tailgate will be locked or unlocked asdesired. It is also possible to operate the out-side rear-view mirrors.
Press the LOCK switch (1). All the doors andthe tailgate will be locked. The turn-signallamps will blink once when the doors and thetailgate are locked.Press the UNLOCK switch (2). All the doorsand the tailgate will be unlocked. If the doorsand tailgate are unlocked when the front roomlamp switch is in the “DOOR” position or therear room lamp switch is in the middle (
z)
position, the room lamp will illuminate for
Electronic immobilizer (Anti-theft starting system)
NOTE
zIf the plug-in hybrid EV system does notstart, we recommend you to contact yourMITSUBISHI MOTORS Authorised ServicePoint.
zIf you lose one of ke
yless operation keys,
contact your MITSUBISHI MOTORSAuthorised Service Poin
t as soon as possible.
To o b t a i n a r e p l a c e m e n t o r e x t r a s p a r e k e y,take your vehicle and all remaining keys toyour MITSUBISHI MOTORS AuthorisedService Point. All the keys have to be re-reg-istered in the immobiliser computer unit. Theimmobilizer can register as follows.•Keyless operation key: up to 4 differentkeysCAUTIONzDo not modify or add parts to the immobi-lizer system. Doing so could cause theimmobilizer to malfunction.
Keyless entry system
NOTE
1- LOCK switch2- UNLOCK switch3- Electric tailgate switch*4- Indicator lampTo l o c k To u n l o c k
BK0203201EN.book 3 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless entry system4-4 Locking and unlocking
4
approximately 15 seconds and the turn-signallamps will blink twice.The position and tail lamps can also be set toturn on for about 30 seconds. Refer to“Instruments and controls: Welcome light” onpage 6-43.
E00310801259
Within 30 seconds of locking the doors andtailgate using the LOCK switch (1), press theLOCK switch twice rapidly to fold the out-side rear-view mirrors.
Within 30 seconds of unlocking the doors andtailgate using the UNLOCK switch (2), pressthe UNLOCK switch twice rapidly to returnthe outside rear-view mirrors to theirextended positions.The outside rear-view mirrors are not initiallyset to work as described above. If you wantthem to work as described above, you need toset them so that they do not retract/extendwhen the doors and tailgate arelocked/unlocked using the keyless entry sys-tem or keyless operation function.Refer to “Starting and driving: Outside rear-view mirrors” on page 7-7.For details, please consult a MITSUBISHIMOTORS Authorised Service Point.In a vehicle equipped with the MitsubishiMulti-Communication System (MMCS), it ispossible to change the setting by means ofscreen operations.Refer to the separate owner’s manual fordetails.
NOTE
zThe door and tailgate
unlock function can be
set so that only the driver’s door unlockswhen the UNLOCK switch (2) is pressedonce.If the door and tailgate unlock function is setto work as described above, all the doors andthe tailgate unlock when the UNLOCKswitch is pressed two times in succession.Refer to “Setting of door and tailgate unlockfunction” on page 4-5.zIf the UNLOCK switch (2) is pressed andany of the doors or ta
ilgate is not opened
within approximately 30 seconds, relockingwill automatically occur.zIt is possible to modify
functions as follows:
For further informati
on, please contact your
MITSUBISHI MOTORS Authorised ServicePoint. On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.•The time for automatic relocking can bechanged.
•The confirmation function (blinking of theturn-signal lamps) can be set to operateonly when the doors and tailgate are lockedor only when the doors and tailgate areunlocked.•The confirmation func
tion (this indicates
locking or unlocking of
the doors and tail-
gate with the blink of the turn-signal lamps)can be deactivated.•The number of times the turn-signal lampsare blinked by the confirmation functioncan be changed.
Operation of the outside rear-view mirrors (Vehicles equipped with the mirror retractor switch) To f o l d
NOTE
To e x t e n d
NOTE
zThe outside rear-view mirrors automaticallyretract when all the doors and tailgate arelocked using the keyless operation function.Refer to “Starting and driving: Outside rear-view mirrors” on page 7-7.
BK0203201EN.book 4 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless entry system
Locking and unlocking 4-5
4
E00310301296
The door and tailgate unlock function can beset to the following two conditions.Each time the door and tailgate unlock func-tion is set, a chime will sound to tell you thecondition of the door and tailgate unlockfunction.1. Put the operation mode in OFF.2. Place the combination headlamps and dip-per switch in the “OFF” position, andleave the driver’s door open.3. Press the LOCK switch (1) for 4 to 10seconds and press the UNLOCK switch(2) during this time.
4. Release in sequence the LOCK andUNLOCK switches within 10 seconds ofpressing the LOCK switch in step 3.
E00309501243
Before replacing the battery, remove staticelectricity from your body by touching ametal grounded object.
zThe keyless entry system does not operatewhen the door or tailgate is open.zThe remote control switch will operatewithin about 4 m from the vehicle. However,the operating range of the remote controlswitch may change if the vehicle is locatednear a power station,
or radio/TV broadcast-
ing station.zIf either of the following problems occurs,the battery may be exhausted.•The remote control switch is operated at thecorrect distance from the vehicle, but thedoors and tailgate are
not locked/unlocked
in response.•The indicator lamp (4) is dim or does notcome on.For further information, please consult yourMITSUBISHI MOTORS Authorised Ser-vice Point.If you replace the battery yourself, refer to“Procedure for replacing the remote controlswitch battery” on page 4-5.
zIf your remote control switch is lost or dam-aged, please contact
your MITSUBISHI
MOTORS Authorised Service Point for areplacement remote control switch.zIf you wish to add a remote control switch,we recommend you to contact yourMITSUBISHI MOTORS Authorised ServicePoint.The below remote control switches are avail-able for your vehicle.NOTE
•Keyless operation key: up to 4 remote con-trol switches
Setting of door and tailgate unlock function Number of chimes
Condition
One chime
All doors and the tailgate unlock
Tw o chimes
Driver’s door unlock only
NOTE
NOTE
zOn vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the se
parate owner’s manual
for details.
Procedure for replacing the remote control switch battery
BK0203201EN.book 5 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system
Locking and unlocking 4-7
4
Yo u c a n l i m i t t h e p o s s i b l e o p e r a t i o n s o fthe keyless operation system in the fol-lowing ways. (The keyless operation sys-tem can be used as a keyless entrysystem.) Please consult a MITSUBISHIMOTORS Authorised Service Point.
•You can limit operations to locking andunlocking the doors and tailgate.•You can limit operations to starting theengine.• The keyless operation system can be dis-abled.When keyless operation system opera-tions are modified, the transmitters oper-ate as follows.•Only locking and unlocking doors ortailgate: exterior transmitter and interiortransmitter•Only starting the engine: interior trans-mitter
E00305700556
If you are carrying the keyless operation key,enter the operating range of the keyless oper-
WA R N I N GzWhen using electromedical devices otherthan implantable cardiac pacemakers orimplantable cardiovascular-defibrilla-tors, contact the electromedical devicemanufacturer ahead of time to determinethe affects of radio waves on the devices.Electromedical device operations could beaffected by radio waves.
NOTE
zThe keyless operation ke
y uses an ultra-weak
electromagnetic wave. In the followingcases, the keyless ope
ration system may not
operate properly or
may be unstable.
•When there is equipment nearby that emitsstrong radio waves, such as: a power sta-tion, a radio/TV broa
dcasting station or an
airport.•The keyless operation system is carriedtogether with a communications devicesuch as a cellular phone
or radio set, or with
an electronic device such as a personalcomputer.•The keyless operati
on key is touching or
covered by a metal object.
•A keyless entry system is being usednearby.•When the keyless operation key battery isworn out.•When the keyless operation key is set downin an area with strong radio waves or noise.In such cases, use the emergency key.Refer to “To operate
without using the key-
less operation functi
on” on page 4-13.
zBecause the keyless operation key receivessignals in order to communicate with thetransmitters in the vehicle, the battery con-tinually wears down regardless of keylessoperation key use. The battery life is 1 to 3years, depending on usage conditions. Whenthe battery wears out, replace the batteryaccording to the description in this manual orhave it replaced at your MITSUBISHIMOTORS Authorised Service Point.Refer to “Procedure for replacing the remotecontrol switch battery” on page 4-5.zBecause the keyless
operation key continu-
ally receives signals, strong radio wavereception could affect battery wear. Do notleave the key near a TV, personal computer,or other electronic device.
Operating range of the keyless operation system
NOTE
BK0203201EN.book 7 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system4-10 Locking and unlocking
4
time, the room lamp will turn on for 15 sec-onds. The turn-signal lamps will blink twice.If the driver’s or front passenger’s doorlock/unlock switch is pressed and any of thedoors or tailgate is not opened within approx-imately 30 seconds, relocking will automati-cally occur.Also refer to “Locking and unlocking: Doors,Central door locks, Tailgate” on pages 4-14,4-15 and 4-16.
Operation can be confirmed as shown below.However, the room lamp will only illuminateif the front room lamp switch is in the“DOOR” position or the rear room lampswitch is in the middle (
z) position.
Driver’s and front passenger’s door lock/unlock switchesTa i l g a t e o p e n s w i t c h
NOTE
zFor vehicles equipped wi
th the mirror retrac-
tor switch, the outside rear-view mirrorsautomatically extend when all the doors andtailgate are unlocked us
ing the keyless oper-
ation function.Refer to “Starting and driving: Outside rear-view mirrors” on page 7-7.zThe keyless operation f
unction can be set so
that only the driver’s door unlocks when thedriver’s door lock/unlock switch is pressed.If the keyless operati
on function is set to
work as described above, all the doors andthe tailgate unlock when the driver’s doorlock/unlock switch is pressed two times insuccession.Refer to “Setting of door and tailgate unlockfunction” on page 4-5.zThe keyless operation function does notoperate under the following conditions:•A door or the tailgate is open or ajar.zIn order to make it possible to check that thedoors and tailgate are locked, you cannotunlock them by using the tailgate openswitch for 3 seconds after locking them.zThe time allowed for checking that the vehi-cle is locked can be adjusted. For furtherinformation, please contact your authorisedMITSUBISHI MOTORS dealer.On vehicles equipped
with Mitsubishi Multi-
Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the se
parate owner’s manual
for details.
zThe time between unlocking and automaticlocking can be adjusted. Please consult aMITSUBISHI MOTORS Authorised ServicePoint.On vehicles equipped with Mitsubishi Multi-Communication System (MMCS), screenoperations can be used to make the adjust-ment. Refer to the separate owner’s manualfor details.
Operation confirmation when lockingand unlockingWhen lock-ing:
The turn-signal lamps blinkonce.
Whenunlocking:
The room lamp illuminates forabout 15 seconds, the turn-signallamps blink twice.
NOTE
BK0203201EN.book 10 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system
Locking and unlocking 4-11
4
E00305901715
In order to prevent vehicle theft or the accidental operation of
the keyless operation system, the buzzer and the display on th
e information screen
in the multi-information display are used to alert the driver.If a warning is activated, always check the vehicle and the keyless operation key. The warning is also displayed if there is a
fault in the keyless
operation system.
NOTE
zFunctions can be modified as stated below.For further information, please contact yourMITSUBISHI MOTORS Authorised ServicePoint.On vehicles equipped with Mitsubishi Multi-Communication System (MMCS), screenoperations can be used
to make the adjust-
ment. Refer to the se
parate owner’s manual
for details.
•Set the confirmation function (blinking ofthe turn-signal lamps) to operate only whenthe vehicle is locked or only when the vehi-cle is unlocked.•Disable the operation confirmation function(blinking of the turn-signal lamps).•Change the number of blinks for the opera-tion confirmation function (blinks of theturn-signal lamps).NOTE
Wa r n i n g a c t i v a t i o n
Item
Display
Buzzer
Note (Solution)
Detection of failure
Inner buzzer sounds once
There is a fault in the keyless operation system.
Fall of battery voltage
Inner buzzer sounds once
The battery starts to run out, the warning is activated.
（The warning is
not activated if the battery is completely dead.
）
BK0203201EN.book 11 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Keyless operation system4-12 Locking and unlocking
4
Key not detected
Inner buzzer sounds once
When the engine switch is turned to the ACC or ON from OFF or when the engine is started, the warning is activated, if any of the following conditions is occurred.•••Carrying another keyless operation key with a different code, or the keyless operation key could be outside the operating range.The battery of the keyless operation key is dead.Communication is blocked by electric wave environment.
Keyless operation key reminder
Inner buzzer sounds about 1 minuteOuter buzzer sounds about 3 seconds inter-mittently
If the operation mode is in OFF and the driver’s door is opened with the keyless operation key in the key slot, a warning is issued and the outer buzzer sounds for about 3 seconds and the inner buzzer sounds for about 1 minute to remind you to remove the key. If the key removed from key slot, the buzzer is stopped.
Keyless operation key take-out monitoring system
Inner buzzer sounds onceOuter buzzer sounds intermittently
••••When the vehicle is parked with the operation mode in any mode other than OFF, if you close the door after opening any of the doors and taking the keyless operation key out of the vehicle, a warning is issued until the key is detected in the vehicle.If you take the keyless operation key out of the vehicle through a window without opening a door, the keyless operation key take-out monitoring system does not operate.It is possible to change the setting to make the keyless operation key take-out monitoring system operate if you take the keyless operation key out from the vehicle through a window without opening a door. For further information, please contact a MITSUBISHI MOTORS Authorised Service Point.Even if you have the keyless operation key within the engine start operating range, if the keyless operation key and vehicle ID codes cannot be matched, for example due to the ambient environment or electromagnetic conditions, the warning may be activated.
Item
Display
Buzzer
Note (Solution)
BK0203201EN.book 12 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Central door locks
Locking and unlocking 4-15
4
Set the inside lock knob (1) to the lockedposition and close the door (2).
E00300801937
Using the central door lock switch on thedriver’s door locks or unlocks all doors andthe tailgate.
E00311301310
Yo u c a n s e l e c t t h e f u n c t i o n t o u n l o c k t h edoors and tailgate using the engine switch.This functions is not activated when the vehi-cle is shipped from the factory. To activate or
deactivate this function, please contact aMITSUBISHI MOTORS Authorised ServicePoint.All doors and the tailgate will unlock when-ever the operation mode is put in OFF.
E00300901042
Child protection helps prevent the rear doorsfrom being opened accidentally from theinside.
To l o c k w i t h o u t u s i n g t h e k e y Front passenger’s door, Rear door Central door locks
NOTE
zRepeated continuous
operation between lock
and unlock could activate the central doorlocking systems built-in protection circuitand prevent the system from operating. Ifthis occurs, wait about
1 minute before oper-
ating the central door lock switch.zWhen the driver’s door is open, the centraldoor lock switch cannot be used to lock it.
To l o c k a n d u n l o c k t h e d o o r s and tailgate Using the central door lock switch 1- Lock
2- Unlock
To unlock the doors and tail-gate LHD
RHD
Using the power switch “Child-protection” rear doors 1- Lock2- Unlock
BK0203201EN.book 15 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分