2014 MITSUBISHI OUTLANDER SPORT brake light

Anti-lock brake system (ABS)Starting and driving 7-31
7
E00607302423
zAv o i d h a r d b r a k i n g a n d h i g h - s p e e d d r i v -ing. Stop the vehicle in a safe place.Restart the Plug-in Hybrid EV Systemand check to see whether the lamp goesout after a few minutes driving; if it thenremains off during driving, there is noproblem.However, if the lamp does not go out, or ifit lights up again when the vehicle isdriven, we recommend you to have thevehicle checked as soon as possible.zIf you start Plug-in Hybrid EV Systemwhen the auxiliary battery voltage isinsufficient, ABS warning lamp/displaymay illuminate, but this is not a failure ofABS. When the drive battery is charged,the auxiliary battery is also charged, andthe warning lamp/display will go out. Ifthe warning lamp/display continues illu-minating even after the battery is suffi-ciently charged or the warninglamp/display illuminates frequently ,haveyour vehicle inspected by a MITSUBISHIMOTORS Authorised Service Point.
Wa r n i n g l a m p

Warning displayThe ABS and brake force distribution func-tion may not work, so hard braking couldmake the vehicle unstable.Av o i d h a r d b r a k i n g a n d h i g h - s p e e d d r i v i n g .Stop the vehicle in a safe place immediatelyand contact a MITSUBISHI MOTORSAuthorised Service Point.
E00618800219
After driving on snowy roads, remove anysnow and ice which may have becomeadhered to the wheel areas.When doing this, be careful not to damage thewheel speed sensors (A) and cables located ateach wheel on vehicles equipped with anABS.
If the warning lamp / display illuminate while driving If only the ABS warning lamp/dis-play illuminate
If the ABS warning lamp / display and brake warning lamp / display illuminate at the same time
NOTE
zThe ABS warning lamp and brake warninglamp illuminate at the same time and thewarning displays appe
ar alternately on the
information screen in the multi informationdisplay.
After driving on icy roads Front
Rear
BK0203201EN.book 31 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*
Starting and driving 7-49
7
Wi t h t h e A C C tu r ned on ( i n th e ‘ s t an dbystate’), push down the “SET -” switch whiledriving.When your desired speed is reached, releasethe “SET -” switch; then this speed is set andthe ACC initiates the speed control to the setspeed.
The set speed is indicated on the informationscreen of the multi-information display.The ACC can be selected between approxi-mately 40 km/h to 180 km/h.Yo u c a n s e t a n d i n i t i a t e t h e s p e e d c o n t r o lwhen driving at approximately 10-40 km/hwhile a vehicle in front is being detected. Inthis case, the target speed is set to 40 km/h.Setting to any speed outside this range doesnot cause the ACC to start the control.When the ACC is initialized, a buzzer soundis heard and the “SET” indicator lights up onthe screen. At the same time, the displayshowing the following distance setting andthe running-ahead vehicle symbol (only whenthe ACC is detecting a vehicle in front) isswitched to the in-control mode display.
NOTE
zEven if the ACC is in the activated statewhen the operation mode is set to “OFF”, thesystem does not automatically become acti-vated when the operation mode is set to“ON” next time.
To a c t i v a t e A C C c o n t r o l

NOTE
zThe ACC cannot start the control when anyof the following conditions is present. Youare alerted to this state by a sounding buzzer.•When the vehicle speed is lower thanapproximately 10 km/h or 180 km/h orhigher.•When the vehicle is running at a speedbetween approximately 10 and 40 km/h andthe ACC is not detecting any vehicle infront.•When the ASC is in the OFF state.•When ABS, ASC or TCL is working.•When the selector lever is in a positionother than “D” (DRIVE).• While the brake pedal is being depressed.•When the parking brake is engaged.•When the system determines that its perfor-mance has been degraded due to contami-nants adhered to the sensor.•When there is any abnormality in the sys-tem.
BK0203201EN.book 49 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Adaptive Cruise Control System (ACC)*
Starting and driving 7-53
7
zWhen the select position is other than“D”.zWhen the parking brake is engaged.zWhen the ACC is self-cancelled becausethe system determines that its perfor-mance has declined and it cannot operatetemporarily due to the following situa-tions, the driver is informed by a buzzerand an indication on the screen.•Under adverse weather conditions (rain,snow, sand storms, etc.)•When the sensor is dirty or blocked bysnow and ice.•When a preceding or oncoming vehiclesplashes water, snow, or sand in front ofthe sensor.•The brake pads are overheating.•When you are driving in light traffic withfew vehicles and obstacles in front.
When the ACC returns to normal opera-tion, the indicator is cancelled. If the indi-cator continues, there may be a fault in thesystem. Please contact a MITSUBISHIMOTORS Authorised Service Point.zWhen some problem occurs with the sys-tem. (In this situation, the ACC control isautomatically cancelled and the system isturned off. You are alerted to this situationby the sound of a buzzer and a message onthe display. If the message remains dis-played even after setting the operationmode to “ON”, please contact a MIT-SUBISHI MOTORS Authorised ServicePoint.)
zWhen some other condition which causesthe control to terminate occurs. (This situ-ation may indicate a fault. Turn off theACC and please contact a MITSUBISHIMOTORS Authorised Service Point.)
Press the “ACC ON/OFF” switch when theACC is in the ‘ON state’ to turn off the ACC.
WA R N I N GzAlthough the set speed driving will bedeactivated when shifting to the “N”(NEUTRAL) position, never move theselector lever to the “N” (NEUTRAL)position while regenerative braking andcould cause a serious accident.
To turn off ACC
BK0203201EN.book 53 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Forward Collision Mitigation System (FCM)*7-58 Starting and driving
7
*: When judging the state that detection per-formance deterioration and the FCM can’toperate temporarily by these situations auto-matically, “FCM TEMPORARILY NOTAVA I L A B L E ” m e s s a g e i s i n d i c a t e d , a n d a“FCM OFF” indicator lights up.Additionally, it may be indicated in the fol-lowing situations.•When the brake is over heating.•When you are driving in light traffic withfew vehicles and obs
tacles in front.
When the FCM will be in the state which canoperate, indication is released automatically.When indication keeps going out, there is anabnormal possibility of the system. Pleasecontact a MITSUBISHI MOTORS Author-ised Service Point.zFactors such as the positional relationshipbetween your vehicle and a vehicle in front,driver’s own technique of steering the vehi-cle and irregularly moving traffic due toaccidents or vehicle trouble may deter theFCM control and alarm from functioning.CAUTION
zWhen the system recognizes driver’s steer-ing or accelerating actions as evasive actionsto avoid collision, the FCM control andalarm functions may be canceled.zThe FCM control and alarm functions maybe triggered in the following situations.•When there is a structure (B) beside theentrance of a curve and intersection.•When running on a na
rrow iron bridge.
•When passing through a gate with smallhead or side clearances.•When there are metallic objects, steps orprojections on the road surface.•When quickly approaching a vehicle infront to overtake it.•When passing an electronic toll collectiongate.•When running under an
overpass, an pedes-
trian overpass or a small tunnel.•When running in Multi-storey car park.•When running the road the gradientchanges suddenly.•When stopping very close to a wall or avehicle in front.CAUTION
B
•When passing close to the vehicle or anobject.•When driving on the road that the vehicle infront runs in offset
position from your vehi-
cle.
zTurn off the system beforehand when thevehicle is placed in a
ny of the following situ-
ations as the system can operate unexpect-edly.•When your vehicle’s wheels are driven bythe Plug-in Hybrid EV System on a lift.•When your vehicle is towed or your vehicletows another vehicle.•When your vehicle is carried on a truck.•When enjoying sports driving on a circuit.•When your vehicle is on a chassisdynamometer or free rollers.•When the tyre pressure is not proper. CAUTION
BK0203201EN.book 58 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Towing caravans and trailersStarting and driving 7-71
7
E00610401405
Yo u r v e h i c l e h a s q u a l i t i e s w h i c h m a k e i t w e l lsuited for normal towing operations provideda few recommendations are observed. Theseare primarily concerne
d with the prevention
of overloading of the vehicle and with theselection of the proper equipment. If theseprecautions are taken and driving habits areregulated accordingly, the effects of towingtrailers and caravans can be minimized.It should be noted that damage to the vehiclecaused directly or indirectly by operatingunder conditions outside the limits set out onthis page will void the warranty, relative tosuch damage.
The legal authorities require that a trailer orcaravan be fitted with stop, tail and turn sig-nal lamps. An electrical kit can be fitted byyour authorized MITSUBISHI MOTORSdealer which meets legal requirements andcan be left on your vehicle permanently. Itmay be necessary to fit additional rear visionmirrors to both sides of your vehicle to giveclear vision past your trailer or caravan.Ensure that your trailer or caravan complieswith the regulations of the particular State inwhich you are travelling, e. g. lighting, safetychains, brakes, mass, etc. Check that yourtowbar tongue does not obscure your vehi-cle’s number plate when the trailer or caravanis disconnected. If it does, remove the tongueensuring that it is refitted securely when refit-ted.
The maximum payload of the towing vehicledoes not exceed the requirements of eachmaximum mass described in the “Vehiclemass”. See “Specifications” for the payloadinformation.Having established compliance with the Stateregulations for permissible towing loads and
To w i n g c a r a v a n s a n d t r a i l -ers
WA R N I N GzWhen connecting the trailer with ElectricTr a i l e r B r a k e ( E T B )
, use MITSUBISHI
MOTORS GENUINE ETB harness.zIf using an ETB harness other than MIT-SUBISHI MOTORS GENUINE parts, anunexpected reduction in drive force mayoccur when using the manual trailerbrake override which co
uld lead to insta-
bility and increase the risk of an accident.
CAUTIONzMITSUBISHI MOTORS recommends theuse of MITSUBISHI MOTORS towingequipment where it is available. No recom-mendation is made as to the make of equip-ment which may be used if MITSUBISHIMOTORS equipment is not available.zThe loads specified apply only if a MITSUB-ISHI MOTORS GENUINE Parts Tow Barand other specified equipment is used.
State re gulations
Permissible towing load and requirements
CAUTIONzThe trailer brake and towing hitch require-ments as specified are minimum require-ments only and MITSUBISHI MOTORSrecommend that a trailer brake and a loaddistributing hitch is used whenever you aretowing, to improve
stopping distance and
towing stability.When using a load distributing hitch the loadon the trailer tyres increases. Do not exceedthe trailer tyre load rating.With all towing operations it is important tolimit the towing vehicle payload as noted.Failure to do so may result in exceeding themaximum load rating of the tyres. This rat-ing is marked on the tyre placard and mayalso be displayed on
the tyre sidewall.
Setting up for towing
BK0203201EN.book 71 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Towing caravans and trailers7-72 Starting and driving
7
brake/hitch requirements, adjust the positionof the load in the trailer to achieve the specifi-cation requirements.Select the appropriate hitch combinationwhich is to be used in conjunction with theMITSUBISHI MOTORS approved parts tow-bar. If you use the load distributing hitch, itmust be installed in accordance with the man-ufacturer’s instructions.It is recommended that two safety chains areused. The chains should be
crossed
under the
trailer draw bar so that the draw bar is pre-vented from touching the ground if itbecomes detached from the vehicle. Thechains must not stop the trailer from turningfreely. Correct load rated shackles must beused to attach the chains. In some states andterritories, a single safety chain is permittedby regulation. Be sure it is attached with cor-rect load rated shackles.For further information about the selectionand use of towing equipment, consult a MIT-SUBISHI MOTORS Authorised ServicePoint.
Have your vehicle serviced prior to towing aheavy trailer or caravan, taking particularcare of the state of Plug-in Hybrid EV Systemtune, the condition of brakes, steering andtyres.Adjust tyre pressures to those quoted for afully laden vehicle (see Tyre placard).Check the tyres, wiring and brakes (if fitted)on the caravan / trailer.Have the cooling system checked and ensurethat the radiator intake is clear to allow maxi-mum air flow through the radiator. Do not
place restrictions in front of the radiator(water bags, driving lamps, insect screens,non MITSUBISHI MOTORS approved bull-bars, etc.) as they restrict air flows.Check that tow bar fixing bolts are tightenedto specification.After a loaded caravan has been connected tothe vehicle, there may be a slight change invehicle attitude which for your night drivingsafety may require the headlamps to be re-aimed.If you have never towed before, connect yourtrailer or caravan and take it for a run overfamiliar ground in your own district. Feel thedifference in acceleration, handling and brak-ing and you are less likely to be surprised ifan emergency does occur, when you are awayfrom home territory. The other driving mem-bers of your family should also becomefamiliar with the vehicle in this condition.If particularly steep or long downgrades areencountered, avoid “riding” the brakes.Apply the brakes firmly to reduce speed andthen remove your foot from the pedal to
Operating hints Ve h i c l e p r e p a r a t i o n Example
Driver preparation Hill climbing
BK0203201EN.book 72 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Operation under adverse driving conditions
For emergencies 9-23
9
zDo not drive on a flooded road. If youdrive on a flooded road, not only the Plug-in Hybrid EV System stops but also a fail-ure like electric leakage or short circuitmay occur.If you inevitably had to run on a floodedroad and the vehicle was exposed towater, be sure to have your vehicleinspected by a MITSUBISHI MOTORSAuthorised Service Point.zIf there is water on the brakes after driv-ing through puddles or washing the vehi-cle, resulting in temporarily ineffectivebrakes. In such cases, lightly depress thebrake pedal to see if the brakes operateproperly. If they do not, lightly depressthe pedal several times while driving inorder to dry the brake pads.zWhen driving in rain or on a road withmany puddles a layer of water may formbetween the tyres and the road surface.This reduces a tyre’s frictional resistanceon the road, resulting in loss of steeringstability and braking capability.To c o p e w i t h t h i s , o b s e r v e t h e f o l l o w i n gitems:
zWhen driving on a snow-covered or fro-zen road, it is recommended that you usesnow tyres or snow traction device (tyrechains).Refer to the “Snow tyres” and “Snowtraction device (tyre chains)” sections.zAv o i d h i g h - s p e e d o p e r a t i o n , s u d d e nacceleration, abrupt brake application andsharp cornering.zDepressing the brake pedal during travelon snowy or icy roads may cause tyreslippage and skidding. When tractionbetween the tyres and the road is reducedthe wheels may skid and the vehicle can-not readily be brought to a stop by con-ventional braking techniques. Brakingwill differ, depending upon whether youhave anti-lock brake system (ABS). Asyour vehicle is equipped with ABS, brakeby pressing the brake pedal hard, andkeeping it pressed.zAllow extra distance between your vehi-cle and the vehicle in front of you, andavoid sudden braking.
zAccumulation of ice on the braking sys-tem can cause the wheels to lock. Pullaway from a standstill slowly after con-firming safety around the vehicle.
Drive as slow as possible when driving onbumpy or rutted roads.This vehicle is intended for driving mainlyon roads with firm surface.4WD system makes possible driving on roadswithout special coverage, on flat and firmsurface. Please, remember that off-road abil-ity of your vehicle is limited. Your vehicle isnot intended for driving in heavy off-road,overcoming the rugged terrain, deep ruts, etc.
On a flooded road (a)Drive your vehicle at a slow speed.(b)Do not drive on worn tyres.
(c)Always maintain the specified tyre infla-tion pressures.
On a snow-covered or frozen road
CAUTIONzDo not press the accelerator pedal rapidly. Ifthe wheels break free of the ice, the vehiclecould suddenly start
moving and possibly
cause an accident.
On a bumpy or rutted road
CAUTIONzThe impact on tyres and/or wheels whendriving on a bumpy or rutted road can dam-age the tyre and/or wheel.
BK0203201EN.book 23 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分

Cleaning the exterior of your vehicle10-4 Vehicle care
10
Sea water contains salt, which generallyaccelerates corrosion of both ferrous and non-ferrous materials. Wind born spray from thesea can distribute salt for a distance of up to20 km from the shore line with prevailing on-shore winds, although the effect is generallyworse within 2 km of the shore. Salt spraycovers roads, and may be passed to your vehi-cle as dust, or as salt spray after rain. For thisreason it is important to wash all the vehicleincluding the underside (not forgetting theplug-in hybrid EV system bay and plug-inhybrid EV system bay components). See sec-tion entitled “Engine compartment” for rec-ommended cleaning practices.Ensure you request a MITSUBISHIMOTORS Authorised Service Point to con-duct the scheduled Preventative Maintenancecorrosion inspection if you live within 20 kmof the sea. Sea water spray in coastal condi-tions
WA R N I N GzDo not wash the vehicle while charging thetraction battery.Doing so could cause a fire or an electricshock.
zBefore washing the vehicle, make surethat the charging lid
and the inner lid are
completely closed.If the lid is open, the charging unit isexposed to water, resulting in a fire or anelectric shock.CAUTIONzWhen washing the under
side of your vehicle
or wheel, be careful not to injure your hands.zIf your vehicle has rain sensor wipers, placethe wiper switch lever in the “OFF” positionto deactivate the rain sensor before washingthe vehicle. Otherwise, the wipers will oper-ate in the presence of water spray on thewindscreen and may get damaged as a result.zRefrain from excessively using a car wash asits brushes may scratch the paint surface,causing it to lose its gloss. Scratches will beespecially visible on da
rker coloured vehi-
cles.zNever spray or splash
water on the electrical
components in the engine compartment.Doing so could have an adverse effect on theplug-in hybrid EV system startability.Exercise caution also when washing theunderbody; be careful not to spray water intothe engine compartment.WA R N I N G
zSome types of hot wa
ter washing equipment
apply high pressure and
heat to the vehicle.
They may cause heat distortion and damageto the vehicle resin parts and may result inflooding of the vehicle interior.Therefore;•Maintain a distance of approx. 70 cm ormore between the vehicle body and thewashing nozzle.•When washing around the door glass, holdthe nozzle at a distance of more than 70 cmand at right angles to the glass surface.
zAfter washing the vehicle, drive the vehicleslowly while lightly depressing the brakepedal several times in order to dry out thebrakes.Leaving the brakes wet could result inreduced braking performance. Also, there isa possibility that they could freeze up orbecome inoperative due
to rust, rendering the
vehicle unable to move.zUsing an automatic car wash, pay attentionto the following items, referring to the opera-tion manual or consulting a car wash opera-tor. If the following procedure is notfollowed, it could result in damage to yourvehicle.•The outside rear-view mirrors are retracted.•The antenna is removed.•The wiper arms are secured in place withtape.CAUTION
BK0203201EN.book 4 ページ ２０１３年１１月１９日　火曜日　午前１１時５０分