2014 MITSUBISHI MIRAGE engine

3-98 Features and controls
3
Tachometer
N00519200292
The tachometer shows engine revolutions per minute. This
allows the driver to determine the most efficient selector posi-
tion and engine speed combinations.
This gauge also assists in evaluating engine performance.
Multi-information display
N00555000278
The multi-information display displays the odometer, trip
odometer, service reminder, fuel remaining, selector lever posi-
tion, average fuel consumption, driving range, etc.
It is also possible to change elements such as the language and
units used on the multi-information display.NOTE
When the ignition switch or the operation mode is in OFF,
the selector lever position display and fuel remaining dis-
play are not displayed.
CAUTION
!
The red zone indicates an engine speed beyond the
range of safe operation.
Select the correct shift position (manual transaxle)
or selector position (CVT) to control the engine
speed so that the tachometer indicator does not
enter the red zone.
1- Information display → P.3-99
2- Service reminder → P.3-103
3- Selector lever position display* → P.3-64
4- Fuel remaining display → P. 3 - 1 0 2
BK0162600US.book 98 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-107
3
Auto reset mode

When the average fuel consumption is being displayed, if
you hold down the multi-information display switch,
these calculations will be reset to zero.

When the engine switch or the operation mode is in the
following conditions, the average fuel consumption dis-
play will automatically reset.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch has been set to the “ACC” or “OFF”
position for about 4 hours or more.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode has been set to ACC or OFF for about
4 hours or more.NOTE
The average fuel consumption display can be reset sepa-
rately for the auto reset mode and for the manual reset
mode.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The initial (default) setting is “Auto reset mode”.
Changing the fuel consumption display unit
N00557100156
The fuel consumption display unit can be changed. The dis-
tance and amount units are also switched to match the selected
fuel consumption unit.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the average fuel consumption display.
Refer to “Information display” on page 3-99.
2. Press and hold the multi-information display switch for
about 5 seconds or more until buzzer sound is heard twice.
3. Press and hold the multi-information display switch to
switch in sequence from “km/L” → “L/100 km” →
“mpg” → “km/L”.
BK0162600US.book 107 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-109
3 Indicator and warning light package
N00519800849
1- High beam indicator → P. 3 - 1 1 0
2- Electric power steering system warning light → P.3-75
3- Tire pressure monitoring system warning light (if so
equipped) → P.3-88
4- Turn signal indicators/Hazard warning lights → P. 3 - 1 1 0
5- Front fog light indicator (if so equipped) → P. 3 - 1 1 0
6- Door-ajar warning light → P. 3 - 1 1 4
7- Supplemental Restraint System (SRS) warning light
→ P.2-44
8- High coolant temperature warning light (red) → P. 3 - 1 1 3
9- Low coolant temperature indicator (green) → P. 3 - 1 1 0
10- Oil pressure warning light → P. 3 - 1 1 3
11- Engine malfunction indicator (“SERVICE ENGINE SOON”
or “Check engine light”) → P. 3 - 1 1 212- Charging system warning light → P. 3 - 1 1 3
13- Brake warning light → P.3-111
14- Anti-lock braking system warning light → P.3-73
15- Multi-information display → P.3-98
16- Driver ’s seat belt reminder/warning light → P.2-18
17- Cruise control indicator (if so equipped) → P.3-81
18- Active stability control (ASC) indicator/warning light →
P.3-78, 3-79
19- Active stability control (ASC) OFF indicator/warning light
→ P.3-78, 3-79
20- ECO indicator → P. 3 - 1 1 0
21- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
22- For details, refer to “Warning activator” on page 3-21 (if so
equipped)
BK0162600US.book 109 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-111
3 Wa r n i n g l i g h t s
N00520300147
Brake warning light and buzzer
N00520400526
This light comes on when the ignition switch is turned to the
“ON” position (engine off) or the operation mode is put in ON.
When the engine is started, the light should go off a few sec-
onds later.
The warning light also illuminates after starting the engine
under the following conditions.

When the parking brake is still applied.

When the brake fluid level is low.

When the brake system circuit is not working properly.
When the vehicle is moving at more than 5 mph (8 km/h) and
the parking brake applied, a buzzer will sound to inform the
driver that the parking brake is not properly release.
Before driving, be sure that the parking brake is fully released
and the brake warning light is off.
CAUTION
!
If the brake warning light and the Anti-lock braking
system warning light are illuminated at the same
time, the braking force distribution function will not
operate, the vehicle may be destabilized during sud-
den braking under the following conditions.
• When the brake warning light does not go out even
when the parking brake is released.
• When the brake warning light stays on while driv-
ing.If the above occurs, avoid sudden braking and high-
speed driving. Park the vehicle in a safe place, and
contact an authorized Mitsubishi Motors dealer or a
repair facility of your choice as soon as possible.

The vehicle should be brought to a halt in the follow-
ing manner when brake performance is deterio-
rated.
• Confirm that the vehicle slows down when you
press down on the brake pedal harder than usual.
In some cases, the brake pedal may go all the way
to the floor.
• Should the brakes fail, use engine braking to
reduce your speed and slowly apply the parking
brake.
Depress the brake pedal to illuminate the stop
lights and to alert the vehicles behind you.
BK0162600US.book 111 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-112 Features and controls
3
Engine malfunction indicator (“SERVICE
ENGINE SOON” or “Check engine light”)
N00520500804
This indicator is a part of the onboard diagnostic (OBD) sys-
tem which monitors the emissions, engine control system or
continuously variable transmission (CVT) control system. If a
problem is detected in one of these systems, this indicator illu-
minates or flashes. When the ignition switch is turned to the
“ON” position or the operation mode is put in ON, this indica-
tor normally comes on and goes off after the engine has started.
This indicator will come on if the fuel tank filler cap is not
properly tightened. If this indicator comes on and stays on after
refueling, stop the engine and check that the cap is properly
tightened. (Turn the cap clockwise until you hear clicking
sounds.)
If this indicator does not go off after several seconds or lights
up while driving, have the system checked as soon as possible
at an authorized Mitsubishi Motors dealer or a repair facility of
your choice.
NOTE
Do not disconnect the battery cable when the engine mal-
function indicator (“SERVICE ENGINE SOON” or
“Check engine light”) is on.
The engine electronic control module stores critical OBD
information (especially exhaust emission data), which
may be lost if the battery cable is disconnected while the
engine malfunction indicator is on. This will make it diffi-
cult to diagnose the cause of future problems.
CAUTION
!
Driving for a long time with the engine malfunction
indicator on may cause more damage to the emission
control system. This could also affect fuel economy
and drivability.
If this indicator does not come on when the ignition
switch is turned to the “ON” position or the opera-
tion mode is put in ON, have the system checked at
an authorized Mitsubishi Motors dealer or a repair
facility of your choice.

If the engine malfunction indicator comes on while
the engine is running, avoid driving at high speeds.
During vehicle operation with the indicator on, the
vehicle may not accelerate when you depress the
accelerator pedal.
When the vehicle is stationary with the indicator on,
you must depress the brake pedal more firmly than
usual since the engine idling speed is higher than
usual and a vehicle with a CVT has a stronger ten-
dency to creep forward.
CAUTION
!
BK0162600US.book 112 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-113
3
Charging system warning light
N00520600313
This light comes on in the event of a malfunction in the charg-
ing system or when the ignition switch is turned to the “ON”
position (engine off) or the operation mode is put in ON. When
the engine is started, the light should go out. Check to make
sure that the light has gone out before driving.Oil pressure warning light
N00520700170
This light comes on when the engine oil pressure is below nor-
mal. If the light stays on while driving, stop the engine as soon
as possible. Do not run the engine until the cause of the low oil
pressure is corrected.
High coolant temperature warning light - red
N00575700011
This light comes on in red if the coolant temperature becomes
excessively high.NOTE
The high coolant temperature warning light may illumi-
nate when the vehicle has been driven at high speeds or on
hilly roads. This illuminating does not necessarily indicate
a problem. It should stop if you keep the engine running
for a while or continue driving the vehicle.
CAUTION
!
If the warning light stays on while the engine is run-
ning, park your vehicle in a safe place as soon as
possible and contact an authorized Mitsubishi
Motors dealer or a repair facility of your choice to
have the system checked.
CAUTION
!
If this light comes on when the engine oil level is not
low, have your vehicle checked at an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.
This warning light does not show the amount of oil
in the crankcase. This can only be determined by
checking the oil level with the dipstick with the
engine turned off.
CAUTION
!
If the light comes on during vehicle operation, it
indicates that the engine is possibly overheating.
Continued driving could make the engine fail.
Immediately stop the vehicle in a safe place and take
appropriate action. (Refer to “Engine overheating”
on page 6-5.)
BK0162600US.book 113 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-115
3
Vehicles equipped with daytime running lights
[When the engine is started, and the parking brake is released]
The daytime running lights will be illuminated:NOTE
Once the daytime running light come on, they do not go
out until the ignition switch is turned to the “OFF” or
“ACC” position or the operation mode is changed to OFF
or ACC.
[When the engine is not running, or when the engine is running
but the parking brake is not released]
The engine starts when the lights are off.NOTE
Do not leave the headlights and other lights on for a long
period of time when the engine is not running. The battery
will run down.
When it rains, or when the vehicle has been washed, the
inside of the lens sometimes becomes foggy. This is the
same as when window glass mists up on a humid day, and
does not indicate a problem. When the light is switched
on, the heat will dry out the fog. However, if water col-
lects inside the light, have it checked by an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.OFF The daytime running lights illuminated
The daytime running lights illuminated
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
OFF All lights off
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
BK0162600US.book 115 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-116 Features and controls
3
Light auto-cutout function (headlights and other
lights)
N00532600570

If the following operation is performed with the combina-
tion headlights and dimmer switch in the “ ” or “ ”
position, the lights automatically turn off.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch is turned to the “OFF” or “ACC” posi-
tion or the key is removed from the ignition switch and the
driver’s door is opened.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode is changed to OFF or ACC and the
driver’s door is opened.

If the following operation is performed with the combina-
tion headlights and dimmer switch in the “ ” or “ ”
position, the lights automatically turn off after about 3
minutes.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch is turned to the “OFF” or “ACC” posi-
tion or the key is removed from the ignition switch and the
driver’s door is not opened.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode is changed to OFF or ACC and the
driver’s door is not opened.NOTE
The light auto-cutout function can be deactivated.
See your authorized Mitsubishi Motors dealer for details.
When you want to keep the lights on:If the combination headlights and dimmer switch is turned to
the “ ” or “ ” position again after the engine is turned off,
the about 3-minute auto-cutout function described above will
not work. The lights (the parking lights, tail lights and license
plate lights) will stay on and will not turn off automatically.
BK0162600US.book 116 ページ ２０１３年３月２２日　金曜日　午後２時４１分