2014 MITSUBISHI MIRAGE battery

Features and controls
3-91
3
2. If the tire pressure monitoring system warning light
remains illuminated after you have been driving for about
20 minutes after you adjust the tire inflation pressure, one
or more of the tires may have a puncture. Inspect the tire
and if it has a puncture, have it repaired by an authorized
Mitsubishi Motors dealer as soon as possible.
NOTE
To avoid the risk of damage to the tire inflation pressure
sensors, have any punctured tire repaired by an authorized
Mitsubishi Motors dealer. If the tire repair is not done by
an authorized Mitsubishi Motors dealer, damage to the tire
inflation pressure sensor is not covered by your warranty.

Do not use an aerosol puncture-repair spray on any tire.
Such a spray could damage the tire inflation pressure sen-
sors.
Have any puncture repaired by an authorized Mitsubishi
Motors dealer.

Using the tire repair kit may damage the tire inflation
pressure sensor. The vehicle must promptly be inspected
and repaired by an authorized Mitsubishi Motors dealer
after using the tire repair kit.
The tire pressure monitoring system may not work normally in
the following circumstances:

A wireless facility or device using the same frequency is
near the vehicle.

Snow or ice is stuck inside the fenders and/or on the
wheels.

The tire inflation pressure sensor’s battery is dead.

Wheels other than Mitsubishi Genuine wheels are being
used.

Wheels that are not fitted with tire inflation pressure sen-
sors are being used.

Wheels whose ID codes are not memorized by the vehicle
are used.

Compact spare tire (if so equipped) is fitted on a road
wheel.

A window tint that affects the radio wave signals is
installed.
WA R N I N G
!
If the warning light illuminates while you are driv-
ing, avoid hard braking, sharp steering maneuvers
and high speeds.
Driving with an under-inflated tire adversely affects
vehicle performance and can result in an accident.
CAUTION
!
The warning light may not illuminate immediately
in the event of a tire blowout or rapid leak.
BK0162600US.book 91 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-100 Features and controls
3
Odometer
N00574900016
The odometer indicates the total distance the vehicle has trav-
eled.Trip odometer
N00575000014
The trip odometer indicates the distance traveled between two
points.To reset the trip odometerTo return the display to 0, hold down the multi-information dis-
play switch for about 1 second or more. Only the currently dis-
played value will be reset.
Example
If trip odometer is displayed, only trip odometer will
be reset.NOTE
Both trip odometers and can count up to 9999.9
miles/kilometers.
When a trip odometer goes past 9999.9 miles/kilometers,
it returns to 0.0 miles/kilometers.

When disconnecting the battery terminal, the memories of
trip odometer displays and are cleared, and their
displays return to “0.0 miles/kilometers”.
Instrument panel light dimmer control
N00575100015
Each time you press the multi-information display switch (2),
there is a sound and the brightness of the instrument panel
lights changes.
Usage examples for trip odometer , trip odometer
It is possible to measure two currently traveled distances,
from home using trip odometer and from a particular
point on the way using trip odometer .
1- Brightness level
2- Multi-information display switch
Bright Dim
BK0162600US.book 100 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-102 Features and controls
3
Average fuel consumption display
N00575300017
This displays the average fuel consumption from the last reset
to the present.
The reset mode conditions for the average fuel consumption
display can be switched between “Auto reset” and “Manual
reset”.
For information on how to change the average fuel consump-
tion display setting, refer to “Changing the function settings”
on page 3-105.NOTE
The average fuel consumption display can be reset sepa-
rately in both auto reset mode and manual reset mode.

“---” is displayed when the average fuel consumption can-
not be measured.

The initial (default) setting is “Auto reset mode”.

Average fuel consumption may vary depend on the driv-
ing conditions (road conditions, how you drive, etc.).
The actual fuel consumption may differ from the fuel con-
sumption displayed, so treat the fuel consumption dis-
played as just a rough guideline.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The display setting can be changed to the preferred units
{mpg, km/L, L/100 km}.
Refer to “Changing the function settings” on page 3-105.
Fuel remaining display
N00575400018
The fuel remaining display indicates the fuel level in the fuel
tank when the ignition switch or the operation mode in ON.NOTE
It may take several seconds to stabilize the display after
refilling the tank.

If fuel is added with the ignition switch or the operation
mode in ON, the remaining fuel display may incorrectly
indicate the fuel level.

The fuel lid mark (A) indicates that the fuel tank filler
door is located on the left side of the vehicle. (Refer to
“Filling the fuel tank” on page 1-4.)1- Full
0- Empty
BK0162600US.book 102 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-107
3
Auto reset mode

When the average fuel consumption is being displayed, if
you hold down the multi-information display switch,
these calculations will be reset to zero.

When the engine switch or the operation mode is in the
following conditions, the average fuel consumption dis-
play will automatically reset.
[Except for vehicles equipped with the F.A.S.T.-key]
The ignition switch has been set to the “ACC” or “OFF”
position for about 4 hours or more.
[For vehicles equipped with the F.A.S.T.-key]
The operation mode has been set to ACC or OFF for about
4 hours or more.NOTE
The average fuel consumption display can be reset sepa-
rately for the auto reset mode and for the manual reset
mode.

Disconnecting the battery cable will erase from memory
the manual reset mode or auto reset mode setting for the
average fuel consumption display.

The initial (default) setting is “Auto reset mode”.
Changing the fuel consumption display unit
N00557100156
The fuel consumption display unit can be changed. The dis-
tance and amount units are also switched to match the selected
fuel consumption unit.
1. When you lightly press the multi-information display
switch a few times, the information display switches to
the average fuel consumption display.
Refer to “Information display” on page 3-99.
2. Press and hold the multi-information display switch for
about 5 seconds or more until buzzer sound is heard twice.
3. Press and hold the multi-information display switch to
switch in sequence from “km/L” → “L/100 km” →
“mpg” → “km/L”.
BK0162600US.book 107 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-108 Features and controls
3
NOTE
The display units for the driving range, the average fuel
consumption are changed, but the units for the indicating
needle (speedometer), the odometer, the trip odometer and
the service reminder will remain unchanged.

If the battery is disconnected, the memory of the unit set-
ting is erased and it returns automatically to factory set-
ting.
The distance units is also changed in the following combina-
tions to match the selected fuel consumption unit.
Fuel
consumption
Distance
(driving range)
km/L km
L/100 km km
mpg mile (s)
BK0162600US.book 108 ページ ２０１３年３月２２日　金曜日　午後２時４１分

3-112 Features and controls
3
Engine malfunction indicator (“SERVICE
ENGINE SOON” or “Check engine light”)
N00520500804
This indicator is a part of the onboard diagnostic (OBD) sys-
tem which monitors the emissions, engine control system or
continuously variable transmission (CVT) control system. If a
problem is detected in one of these systems, this indicator illu-
minates or flashes. When the ignition switch is turned to the
“ON” position or the operation mode is put in ON, this indica-
tor normally comes on and goes off after the engine has started.
This indicator will come on if the fuel tank filler cap is not
properly tightened. If this indicator comes on and stays on after
refueling, stop the engine and check that the cap is properly
tightened. (Turn the cap clockwise until you hear clicking
sounds.)
If this indicator does not go off after several seconds or lights
up while driving, have the system checked as soon as possible
at an authorized Mitsubishi Motors dealer or a repair facility of
your choice.
NOTE
Do not disconnect the battery cable when the engine mal-
function indicator (“SERVICE ENGINE SOON” or
“Check engine light”) is on.
The engine electronic control module stores critical OBD
information (especially exhaust emission data), which
may be lost if the battery cable is disconnected while the
engine malfunction indicator is on. This will make it diffi-
cult to diagnose the cause of future problems.
CAUTION
!
Driving for a long time with the engine malfunction
indicator on may cause more damage to the emission
control system. This could also affect fuel economy
and drivability.
If this indicator does not come on when the ignition
switch is turned to the “ON” position or the opera-
tion mode is put in ON, have the system checked at
an authorized Mitsubishi Motors dealer or a repair
facility of your choice.

If the engine malfunction indicator comes on while
the engine is running, avoid driving at high speeds.
During vehicle operation with the indicator on, the
vehicle may not accelerate when you depress the
accelerator pedal.
When the vehicle is stationary with the indicator on,
you must depress the brake pedal more firmly than
usual since the engine idling speed is higher than
usual and a vehicle with a CVT has a stronger ten-
dency to creep forward.
CAUTION
!
BK0162600US.book 112 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-115
3
Vehicles equipped with daytime running lights
[When the engine is started, and the parking brake is released]
The daytime running lights will be illuminated:NOTE
Once the daytime running light come on, they do not go
out until the ignition switch is turned to the “OFF” or
“ACC” position or the operation mode is changed to OFF
or ACC.
[When the engine is not running, or when the engine is running
but the parking brake is not released]
The engine starts when the lights are off.NOTE
Do not leave the headlights and other lights on for a long
period of time when the engine is not running. The battery
will run down.
When it rains, or when the vehicle has been washed, the
inside of the lens sometimes becomes foggy. This is the
same as when window glass mists up on a humid day, and
does not indicate a problem. When the light is switched
on, the heat will dry out the fog. However, if water col-
lects inside the light, have it checked by an authorized
Mitsubishi Motors dealer or a repair facility of your
choice.OFF The daytime running lights illuminated
The daytime running lights illuminated
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
OFF All lights off
Parking, tail, front and rear side-marker lights, license
plate and instrument panel lights on
Headlights and other lights on
BK0162600US.book 115 ページ ２０１３年３月２２日　金曜日　午後２時４１分

Features and controls
3-119
3
NOTE
A light in the instrument panel flashes to show when the
turn signal lights are working properly.
If this light flashes faster than usual, check for a burned
out turn signal light bulb or malfunctioning connection in
the signal.
If the panel light does not come on when the lever is
moved, check for a blown fuse or a burned out bulb in the
panel.
Have the system inspected by your authorized Mitsubishi
Motors dealer or a repair facility of your choice.

It is possible to modify functions as follows:
• Deactivate the turn signal light 3-flash function for lane
changes.
• Adjust the time required to operate the lever for the 3-
flash function.
• Changing of the tone of a sounding buzzer as the turn
signal lights flash.
See your authorized Mitsubishi Motors dealer for details.
Hazard warning flasher switch
N00522700318
If you press the flasher switch, the turn signals will flash inter-
mittently, and so will the hazard warning lights. This is an
emergency warning system and should not be used when the
vehicle is in motion, except for emergencies.
If you need to leave your vehicle, the flashers will keep work-
ing after the ignition switch is removed or the operation mode
is put in OFF.NOTE
If the flashers are used for several hours, the battery will
run down. This could make it difficult or impossible to
restart your vehicle.
BK0162600US.book 119 ページ ２０１３年３月２２日　金曜日　午後２時４１分