2014 MITSUBISHI ASX clock

WARNINGlA high voltage is present in the power cir-
cuit and in the bulbs and bulb terminals.To avoid the risk of an electric shock, con-
tact a MITSUBISHI MOTORS Author-
ized Service Point whenever repair or re- placement is necessary.Headlamps (High-beam)
E01009400135
1. When replacing the bulb on the left side
of the vehicle in the case of diesel-pow-
ered vehicles, remove the bolt (A) hold-
ing down the relay box and move the re- lay box towards the rear of the vehicle.
*: Front of the vehicle
2. Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle
3. Turn the bulb (C) anticlockwise to re-
move it.
*: Front of the vehicle
4. While holding down the tab (D), pull out
the socket (E).
5. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.
Replacement of lamp bulbs
10-29
OGAE14E1Maintenance10

Position lamps
E01003701090
1.When replacing the bulb on the left side
of the vehicle in the case of diesel-pow-
ered vehicles, remove the bolt (A) hold-
ing down the relay box and move the re- lay box towards the rear of the vehicle.
*: Front of the vehicle
2. When replacing the bulb on the right
side of the vehicle in the case of diesel-
powered vehicles, remove the clips (B)
by prying with a straight blade (or mi- nus) screwdriver, and remove the side
cover.
*: Front of the vehicle
3. Turn the socket (C) anticlockwise to re-
move it.
*: Front of the vehicle
4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
E01003800922
To remove 1. Remove the upper cover. For information regarding how to re-move the upper cover, refer to “Remov-
ing and installing the upper cover and duct” on page 10-09.
Replacement of lamp bulbs
10-30 OGAE14E1Maintenance10

2.Remove the entire socket and bulb as-
sembly (A) by turning it anticlockwise.
*: Front of the vehicle
3. Remove the bulb by pulling it out.
To install 1. To install the bulb, perform the removal
steps in reverse.
2. Install the upper cover.
For information regarding how to installthe upper cover, refer to “Removing and
installing the upper cover and duct” on
page 10-09.Side turn-signal lamps (on
fender)*
E01003900516
NOTEl For the side turn-signal lamps (on fender), it
is not possible to repair or replace just thebulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Side turn-signal lamps (on out-
side rear-view mirror)*
E01003900529
NOTEl An LED, not a bulb, is used in the side turn-
signal lamps (on outside rear-view mirror).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Front fog lamps*
E01004001742
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the
fog lamp cover (A) and pry gently to re- move it.
2. Remove the screws (B), and remove the
lamp unit.
Replacement of lamp bulbs
10-31
OGAE14E1Maintenance10

NOTElExcept for vehicles equipped with daytime
running lamps, when unfastening the screws,be careful not to move the beam position ad-
justment screw (C).
3. While holding down the tab (D), pull out
the socket (E).
4. Turn the bulb (F) anticlockwise to re-
move it.
5. To install the bulb, perform the removal
steps in reverse.
CAUTIONl Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., andrefit it after drying it thoroughly.Daytime running lamps*
E01011200101
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the
daytime running lamp cover (A) and pry gently to remove it.
Replacement of lamp bulbs
10-32 OGAE14E1Maintenance10

2.Remove the screws (B), and then re-
move the lamp unit.
3. Turn the bulb (C) anticlockwise to re-
move it.
4. While holding down the tab (D), pull out
the socket (E).
5. To install the bulb, perform the removal
steps in reverse.
Rear fog lamp
E01004101596
1. When removing the lamp unit (A), push
it towards the left side of the vehicle body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-33
OGAE14E1Maintenance10

NOTElIf the wiring harness is pulled off the 2 har-
ness guides on the lamp unit while replacingthe bulb, make sure to secure the wiring har-
ness to the harness guides.
l When installing the lamp unit, first insert the
tab (C) into the groove (D) on the body, and then push on the lamp unit to fit it into place.Rear combination lamps
E01004201366
1. Remove the screws (A) that hold the
lamp unit and remove the lamp unit.
2. Turn the socket and bulb assembly anti-
clockwise to remove it.
B- Stop and tail lamp (LED) - cannot be
replaced
C- Rear turn-signal lamp
NOTEl An LED, not a bulb, is used in the stop
lamp/tail lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal
steps in reverse.
NOTEl When mounting the lamp unit, align the
groove (D) on the lamp unit with the clip onthe body and the pin (E) on the unit with the
hole in the body.
Replacement of lamp bulbs
10-34 OGAE14E1Maintenance10

Reversing lamps
E01004401430
1. Open the tailgate.
2. Insert a straight blade (or minus) screw-
driver into the notch of the cover and pry
gently to remove the cover.
NOTEl Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
cover.
3. Remove the socket and bulb assembly
by turning it anticlockwise.
4. Remove the bulb by pulling it out.
5. To install the bulb, perform the removal
steps in reverse.NOTEl When installing the lid, align the tab on the
lid with the hole on the vehicle side.
Replacement of lamp bulbs
10-35
OGAE14E1Maintenance10

Licence plate lamps
E01004602093
1. When removing the lamp unit (A), push
it towards the left side of the vehicle body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
NOTEl When installing the lamp, insert tab (C) first
then align and insert tab (D).High-mounted stop lamp
E01004500593
NOTEl An LED, not a bulb, is used in the high-
mounted stop lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Replacement of lamp bulbs
10-36 OGAE14E1Maintenance10