2014 MERCEDES-BENZ CLS lights

The interior lighting automatically switches
on if you:
Runlock the vehicle
Ropenadoor
Rremove the SmartKey from the ignition lock
The interior light is activated forashort while
when the SmartKey is removed from the
ignition lock. You can activatethis delayed
switch-off using the on-board computer
(Ypage 232).
Manualinterior lighting control
Frontoverhead control panel
To switch the rear interior lighting
on/off.
To switch the automatic interior
lighting control on/off
$To switch the right-hand reading
lamp on/off
!\rTo switch the frontinterior lighting
on/off
To switch the left-hand reading lamp
on/off
XTo switch the front interior lighting on/
off:press the\rbutton.
XTo switch the rear interior lighting on/
off:press thebutton.
XTo switch the reading lampson/off:
press thebutton.
Crash-responsive emergency lighting
The interior lighting is activated automatically
if the vehicle is involved in an accident.
XTo switch off the crash-responsive
emergency lighting:press the hazard
warning lamp button.
or
XLock and then unlock the vehicle using the
SmartKey.
Replacing bulbs
Important safety notes
Xenon bulbs
GDANGER
Xenon bulbs carryahigh voltage. You can get
an electric shock if you remove the cover of
the Xenon bulb and touch the electrical
contacts. There isarisk of fatal injury.
Never touch the parts or the electrical
contacts of the Xenon bulb. Always have work
on the Xenon bulbs carried out ataqualified
specialist workshop.
Bulbs and lamps are an importantaspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
LED lamps
You can neither replace Xenon bulbsnor LED
bulbs. Have LED bulbschanged ataqualified
specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp setting checked regularly.
Other bulbs
GWARNING
Bulbs, lamps and connectors can get very hot
when operating. If you changeabulb, you
124Replacing bulbs
Lights and windshield wipers

could burn yourselfonthese components.
There isarisk of injury.
Allow these components to cool down before
changingabulb.
There are bulbs other than Xenon and LED
bulbs that you cannot replace. Replace only
the bulbs listed (Ypage 125). Have the bulbs
that you cannot replace yourself changed at
aqualified specialist workshop.
If you require assistance changing bulbs,
consultaqualified specialist workshop.
Do not touch the glass tube of new bulbs with
your bare hands. Even minor contamination
can burn into the glass surface and reduce
the service life of the bulbs. Always usealint-
free cloth or only touch the base of the bulb
when installing.
Only use bulbs of the correct type.
If the new bulb still does not light up, consult
aqualified specialist workshop.
Bulbs and lamps are an important aspect of
vehicle safety. You must therefore make sure
that these function correctly at all times.
Have the headlamp settingchecked regularly.
Overview: changing bulbs/bulb types
You can change the following bulbs. The bulb
type can be found in the legend.
Tail lamp
Backup lamp:W16W
Changing the rear bulbs
Backup light
Lamp unit
XSwitch off the lights.
XOpen the trunk.
XReach up into the side paneling and pull
downwards until the lamp cluster is easily
accessible.
XPress the detent of connectorand pull
out connector.
XUseasuitable tool to loosen and remove
four nuts.
XRemove the entire lamp cluster.
XTurn bulb holder$counter-clockwise and
pull it out.
XPull out bulb.
XInsert the new bulb into bulb holder$.
XInsert bulb holder$into the lamp and turn
it clockwise.
XRe-insert the lamp cluster.
XTighten four nuts.
XPush in connectoruntil it engages.
XInsert the side paneling.
Windshield wipers
Switching the windshield wiperson/
off
!Do not operatethe windshield wipers
when the windshield is dry, as this could
damage the wiper blades. Moreover, dust
Windshield wipers125
Lights and windshield wipers
Z

Depending on the equipment level of your
vehicle, there aretwo variants of wiperblade;
these are installed and removed in different
ways. Based on the diagrams,checkwhich
system is installed in your vehicle.
Changing the wiper blades (version 1)
Removing the wiper blades
XRemove the SmartKey from the ignition
lock or turn it to position0(KEYLESS-GO).
XFold the wiper arm away from the
windshield until it engages.
XSet the wiper blade at right angles to the
wiper arm.
XRemove the wiper blade from the retaining
pin on the wiper arm in the direction of the
arrow.
Installing the wiper blades
XPush the new wiper blade onto the
retaining pin on the wiper arm in the
opposite direction to the arrow.
Make sure that the wiper blade slides fully
onto the retaining pin on the wiper arm.
XTurn the wiper blade parallel to the wiper
arm.
XFold the wiper arm back onto the
windshield.
Changing the wiper blades (version 2)
Removing the wiper blades
XRemove the SmartKey from the ignition
lock or turn it to position0(KEYLESS-GO).
XFold the wiper arm away from the
windshield until it engages.
XFirmly press release knoband pull the
wiper blade upwards from the wiper arm in
the direction of the arrow.
Installing the wiper blades
XPosition the new wiper blade in the retainer
on the wiper arm and slide it into place in
the opposite direction from the arrow.
The wiper blade audibly engages.
XMake sure that wiper blade is seated
correctly.
XFold the wiper arm back onto the
windshield.
Windshield wipers127
Lights and windshield wipers
Z

Problems with the windshield wipers
ProblemPossible causes/consequences andSolutions
The windshield wipers
are jammed.
Leaves or snow, for example, may be obstructing the windshield
wiper movement.The wiper motor has been deactivated.
XFor safety reasons, you should remove the SmartKey from the
ignition lock.
or
XSwitch off the engine using the Start/Stop button and open the
driver's door.
XRemove the cause of the obstruction.
XSwitch the windshield wipers back on.
The windshield wipers
fail completely.
The windshield wiper drive is malfunctioning.
XSelect another wiper speed on the combination switch.
XHave the windshield wipers checked ataqualified specialist
workshop.
128Windshield wipers
Lights and windshield wipers

Information aboutusing 3-zone
automatic climate control
Automatic climate control
The 3-zone automatic climate control is only
available on vehicles for Canada.
The following contains instructions and
recommendations to enable you to get the
most out of your automatic climate control.
RActivate climate control using the\rand
buttons. The indicatorlamps above
the\randbuttons light up.
RIn automatic mode, you can also use the
buttontosetaclimate mode
(FOCUS/MEDIUM/DIFFUSE). The
MEDIUM levelisrecommended.
RSet thetemperaturetof72‡(22 †).
ROnly use the"Windshield defrosting"
function briefly until thewindshield is clear
again.
ROnly use air-recirculation modebriefly, e.g.
if there are unpleasantoutside odorsor
when inatunnel. The windows could
otherwise fog up, since no fresh air is drawn
intothevehicleinair-recirculation mode.
RUse theZONEfunction to adopt the
temperature settingsonthedriver's side
for the front-passenger side and the rear
compartment as well. The indicatorlamp
above thebutton goes out.
RUse the residual heat function if you want
to heat or ventilate the vehicle interior
when the ignition is switched off. The
residual heat function can only be activated
or deactivated with the ignition switched
off.
RVehicles with COMAND Multimedia-
System:if you change the settings of the
climate control system, the climate status
displayappears for approximately three
seconds at the bottom of the screen in the
COMAND display. See also the separate
COMAND operating instructions. You will
see the current settings of the various
climate control functions.
ECO start/stop function
During automatic engine switch-off,the ECO
start/stop function only operates at a
reduced capacity. If you require the full
climate control output, you can switch off the
ECO start/stop function by pressing the ECO
button (Ypage 152).
Operating the climate control
systems
Switching climate control on/off
Points to observe before use
When the climate control is switched off, the
air supply and air circulation are also
switched off. The windows could fog up.
Therefore, switch off climate control only
briefly
iActivate climate control primarily using
the\rbutton (Ypage 137).
Activating/deactivating
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XTo switch on:press the\rbutton on
the control panel for the climate control.
The indicator lamp in the\rbutton lights
up. Airflow and air distribution are set to
automatic mode.
or
XPress thebutton.
The indicator lamp in thebutton goes
out. The previously selected settings are
restored.
XTo switch off:press thebutton.
The indicator lamp in thebutton lights
up.
Operating the climate control systems135
Climat ec ontrol

Activating/deactivating cooling with
air dehumidification
Pointstoobserve beforeuse
If you deactivatethe"Cooling withair-
dehumidification"function,theair inside the
vehiclewill notbecooled. The air inside the
vehicle will also not be dehumidified. The
windows can fog up more quickly. Therefore,
deactivatethe cooling with air-
dehumidification function only briefly.
The cooling with air dehumidification function
is only available when the engineisrunning.
The air inside the vehicle is cooled and
dehumidified according to the temperature
selected.
Condensation may drip from the underside of
the vehicle when it is in cooling mode. This is
normal and notasign that thereisa
malfunction.
Activating/deactivating
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up.
iWhen the "Cooling with air
dehumidification"function is activated,
one of the indicator lamps on the auxiliary
heating button will light up on vehicles with
auxiliary heating.
XTo deactivate:press thebutton.
The indicator lamp in thebutton goes
out. The "Cooling with air dehumidification"
function hasadelayed switch-off feature.
136Operating theclimatecontrol systems
Climat ec ontrol

Problems with the "Cooling with air dehumidification" function
ProblemPossible causes/consequences andSolutions
The indicator lamp in
thebutton
flashes three times or
remains off. The
"Cooling with air
dehumidification"
function cannot be
switched on.
Cooling with air dehumidification has been deactivated due to a
malfunction.
XVisitaqualified specialist workshop.
Setting climate control to automatic
Points to observe before use
In automatic mode, the set temperature is
maintained automatically ataconstant level.
The system automatically regulates the
temperature of the dispensed air, the airflow
and the air distribution.
The automatic mode functions optimally
when the "Cooling with air dehumidification"
function is activated. If necessary, cooling
with air dehumidification can be deactivated.
If you deactivate the "Cooling with air-
dehumidification" function, the air inside the
vehicle will not be cooled. The air inside the
vehicle will also not be dehumidified. The
windows can fog up more quickly. Therefore,
deactivate the cooling with air-
dehumidification function only briefly.
Activating/switching
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XSet the desired temperature.
XTo activate:press the\rbutton.
The indicator lamp in the\rbutton lights
up. Automatic air distribution and airflow
are activated.
i3-zone automatic climate control: when
automatic mode is activated, you can
selectaclimate mode (Ypage 137).
XTo switch to manualmode:press the
button.
or
XPress theorbutton.
The indicator lamp in the\rbutton goes
out.
Adjusting the climate mode settings
The "Set climate mode" function is only
available with 3-zone automatic climate
control.
You can select the following climate mode
settings in automatic mode:
FOCUS high airflow that is set slightly
cooler
MEDIUM medium airflow, standard setting
DIFFUSE low airflow that is set slightly
warmer and with less draft
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XPress the\rbutton.
XPress thebutton repeatedly until the
desired climate mode appears in the
display.
Operating the climate control systems137
Climate control

Setting the airflow
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XTo increase:press thebutton.
XTo reduce:press thebutton.
iYou can use 3-zone automatic climate
control to set the airflow in the rear
compartmentseparately.
If the batteryisnot sufficiently charged,
blower output may be reduced. As soon as
the batteryissufficiently charged, full blower
output will be available.
Switching the ZONE function on/off
XTo activate:press thebutton.
The indicator lamp above thebutton
lights up.
Dual-zone automatic climate control: the
temperature setting for the driver's side is
not adopted for the front-passenger side.
3-zone automatic climate control: the
temperature setting for the driver's side is
not adopted for the front-passenger side
and the rear compartment.
XTo deactivate:press thebutton.
The indicator lamp above thebutton
goes out.
Dual-zone automatic climate control: the
temperature setting for the driver's side is
adopted for the front-passenger side.
3-zone automatic climate control: the
temperature setting for the driver's side is
adopted for the front-passenger side and
the rear compartment.
Defrosting the windshield
You can use this function to defrost the
windshield or to defrost the inside of the
windshield and the side windows.
Switchoff the "Windshield defrosting"
function as soon as the windshield is clear
again.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
XTo activate:press thebutton.
The indicator lamp in thebutton lights
up.
The climate control system switches to the
following functions:
Rhigh airflow
Rhigh temperature
Rair distribution to the windshield and
frontside windows
Rair-recirculation mode off
If the battery is not sufficiently charged,
blower output may be reduced. Oncethe
battery is sufficiently charged again, full
blower output will be available again.
XTo deactivate:press thebutton.
The indicator lamp in thebutton goes
out. The previously selected settings are
restored. Air-recirculation mode remains
deactivated.
or
XPress the\rbutton.
The indicator lamp in thebutton goes
out. Airflow and air distribution are set to
automatic mode.
or
XDual-zoneautomatic climate control: turn
temperature controlsor%clockwise
or counter-clockwise (Ypage 131).
3-zoneautomatic climate control: turn
temperature controlsor%clockwise
or counter-clockwise (Ypage 134).
or
XPress theorbutton.
MAX COOL maximum cooling
The MAX COOL function is only available in
vehicles for the USA.
Operating theclimate control systems139
Climate control