2014 MAZDA MODEL 6 Owners Manual (in English)

Black plate (257,1)
qWhen The System Operates
1. Press the LDWS switch. The LDWS
goes on stand-by and the LDWS
warning light (amber) illuminates.
On the type A instrument cluster, the
lane indication (bordered line) is
indicated in the display.
Indication on display
2. Drive the vehicle near the center of the
lane and the LDWS indicator light
(green) illuminates in the instrument
cluster when all of the following
conditions are met.
On the type A instrument cluster, the
lane indication is indicated in the
display.
lThe vehicle is driven near the center
of the lane with the white (yellow)
line on the left and right sides, or on
either side.
lThe vehicle speed is about 65 km/h
(41 mph) or more
lThe vehicle is driven on a straight
road or road with gentle curves
Indication on display
NOTElThe LDWS remains on stand-by until it
detects white (yellow) lines on both the left
and right sides, or on either side.
lWhen the system detects a white (yellow)
line on one side only, the system will
operate the warning only when the vehicle
deviates to the side the white (yellow) line
detected.
When Driving
Lane Departure Warning System (LDWS)
4-133
Mazda6_8DQ8-EA-13L_Edition3 Page257
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (258,1)
Auto cancel
Under the following conditions, the
LDWS is automatically canceled and kept
on stand-by, and the LDWS warning light
(amber) in the instrument cluster
illuminates.
On the type A instrument cluster, the lane
indication (bordered line) is indicated in
the display.
The LDWS is automatically enabled when
the condition changes and the system is
operable.
lThe system cannot detect white
(yellow) lines.
lThe vehicle speed is less than about 60
km/h (37 mph).
lThe vehicle is making a sharp curve.lThe vehicle is making a curve at an
inadequate speed.
lThe temperature inside the camera is
high or low.
lThe windshield around the camera is
foggy.
lThe windshield around the camera is
blocked by an obstruction, causing
poor forward visibility.
Auto cancel of warning
Under the following conditions, the
LDWS determines that the driver is
making lane changes and the warning is
automatically canceled.
The LDWS is automatically enabled after
the operation.
lThe steering wheel is operated
abruptly.
lThe brake pedal is depressed abruptly.lThe accelerator pedal is depressed
abruptly.
lA turn signal lever is operated (after
the turn signal lever is returned, the
LDWS warning may not operate for
about 3 seconds which is the period of
time required to make a lane
correction).
NOTE
lAfter about 5 seconds have elapsed with the
turn signal lever left operating, the LDWS
warning may operate if the vehicle is close
to a white (yellow) line.
lThe sensitivity of the warning (sensitivity
with which the system determines the
driver’s intentional lane change) can be
changed.
Refer to Personalization Features on page 9-9.
qCanceling The System
To cancel the LDWS, press the LDWS
switch. The LDWS indicator light (Green/
Amber) in the instrument cluster turns off.
The lane indication displayed in the type
A instrument cluster turns off.
qLDWS Warning
If the system determines that the vehicle
may be deviating from its lane while the
system is operating, the LDWS warning
sounds and the LDWS indicator light
(green) flashes.
Refer to Warning/Indicator Lights on page
4-23.
Refer to Lane Departure Warning System
(LDWS) Warning Sound on page 7-41.
In the display of the type A instrument
cluster, the direction in which the system
determined that the vehicle may be
deviating from its lane is indicated.
Operate the steering wheel adequately and
drive in the center of the lane.
4-134
When Driving
Lane Departure Warning System (LDWS)
Mazda6_8DQ8-EA-13L_Edition3 Page258
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (259,1)
Indication on display
NOTElIf the LDWS warning sound is set to
rumble, the sound will be heard from the
vehicle speaker on the side which the
system determined the vehicle may be
deviating from its lane.
lThe LDWS warning sound may not be
heard depending on the surrounding
conditions such as outside noise.
lThe warning timing with which the system
determines the vehicle may be deviating
from its lane can be changed.
Refer to Personalization Features on page
9-9.
qForward Sensing Camera (FSC)
lThe LDWS camera, located near the
rearview mirror, also functions as the
Forward Sensing Camera (FSC) for the
High Beam Control System (HBC).
lIf the temperature inside the Forward
Sensing Camera (FSC) is extremely
high or low, the LDWS is
automatically canceled and kept on
stand-by, and the LDWS warning light
(amber) in the instrument cluster
flashes. Message information is
indicated in the display in the type A
instrument cluster.
The LDWS is automatically enabled
when the conditions change and the
system is operable.
Forward Sensing Camera (FSC)
When Driving
Lane Departure Warning System (LDWS)
4-135
Mazda6_8DQ8-EA-13L_Edition3 Page259
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (260,1)
CAUTION
Heed the following cautions to assure
the correct operation of the Forward
Sensing Camera (FSC).
ØDo not remove the Forward
Sensing Camera (FSC) cover.
ØConsult an Authorized Mazda
Dealer regarding cleaning of the
camera lens.
ØDo not hit or apply strong force to
the Forward Sensing Camera (FSC)
or the area around it. If the
Forward Sensing Camera (FSC)
has been severely hit, do not use
the LDWS and consult an
Authorized Mazda Dealer.
ØConsult an Authorized Mazda
Dealer before performing repairs
around the Forward Sensing
Camera (FSC).
ØThe Forward Sensing Camera
(FSC) is installed to the windshield.
Consult an Authorized Mazda
Dealer for windshield repair and
replacement.
ØThe direction in which the Forward
Sensing Camera (FSC) is pointed
has been finely adjusted. Do not
change the installation position of
the Forward Sensing Camera (FSC)
or remove it. Otherwise, it could
result in damage or malfunction.
ØBe careful not to scratch the
Forward Sensing Camera (FSC)
lens or allow it to get dirty. Also,
do no take the camera apart.
Otherwise, it could result in
damage or malfunction.
ØAlways keep the windshield glass
around the camera clean by
removing dirt or fogging. Use the
windshield defroster to remove
fogging on the windshield.
4-136
When Driving
Lane Departure Warning System (LDWS)
Mazda6_8DQ8-EA-13L_Edition3 Page260
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (261,1)
Rear View Monitorí
The rear view monitor provides visual images of the rear of the vehicle when reversing.
WARNING
Always drive carefully confirming the safety of the rear and the surrounding
conditions by looking directly with your eyes:
Reversing the vehicle by only looking at the screen is dangerous as it may cause an
accident or a collision with an object. The rear view monitor is only a visual assist
device when reversing the vehicle. The images on the screen may be different from
the actual conditions.
CAUTION
ØDo not use the rear view monitor under the following conditions: Using the rear
view monitor under the following conditions is dangerous and could result in
injury or vehicle damage or both.
ØIcy or snow-covered roads.
ØTire chains or a temporary spare tire is installed.
ØThe trunk lid is not fully closed.
ØThe vehicle is on a road incline.
ØWhen the display is cold, images may course across the monitor or the screen and
may be dimmer than usual, which could cause difficulty in confirming the
surrounding conditions of the vehicle. Always drive carefully confirming the safety
of the rear and the surrounding conditions by looking directly with your eyes.
ØDo not apply excessive force to the camera. The camera position and angle may
deviate.
ØDo not disassemble, modify, or remove it as it may no longer be waterproof.
ØThe camera cover is made of plastic. Do not apply degreasing agents, organic
solvents, wax, or glass coating agents to the camera cover. If any are spilled on
the cover, wipe off with a soft cloth immediately.
ØDo not rub the cover excessively, or polish it using an abrasive compound or a
hard brush. The cover may be damaged affecting the image.
NOTE
lIf water, snow, or mud is stuck on the camera lens, wipe it off using a soft cloth. If it cannot be
wiped off, use a mild detergent.
lIf the camera temperature changes rapidly (Hot to cold, cold to hot), the rear view monitor may
not operate correctly.
lWhen replacing the tires, consult an Authorized Mazda Dealer. Replacing the tires could result in
deviation of the guide lines which appear on the display.
lIf the vehicle's front, side, or rear has been involved in a collision, the alignment of the rear view
parking camera (location, installation angle) may have deviated. Always consult an Authorized
Mazda Dealer to have the vehicle inspected.
When Driving
Rear View Monitor
4-137íSome models. Mazda6_8DQ8-EA-13L_Edition3 Page261
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (262,1)
qRear View Parking Camera Location
Rear View Parking Camera
qSwitching to the Rear View Monitor Display
Shift the shift lever to R with the ignition switched ON to switch the display to the rear
view monitor display.
NOTE
When the shift lever is shifted from R to another shift lever position, the screen returns to the previous
display.
4-138
When Driving
Rear View Monitor
Mazda6_8DQ8-EA-13L_Edition3 Page262
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (263,1)
qDisplayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
(Actual view)
Object Garnish
Bumper
NOTElThe displayable range varies depending on the vehicle and road conditions.lThe displayable range is limited. Objects under the bumper or around the bumper ends cannot be
displayed.
lThe distance appearing in the displayed image is different from the actual distance because the
rear view parking camera is equipped with a specific lens.
lSome optionally installed vehicle accessories may be picked up by the camera. Do not install any
optional parts that can interfere with the camera view, such as illuminating parts or parts made of
reflective material.
lIt may be difficult to see the display under the following conditions, however, it does not indicate a
malfunction.
lIn darkened areas.lWhen the temperature around the lens is high/low.lWhen the camera is wet such as on a rainy day or during periods of high humidity.lWhen foreign material such as mud is stuck around the camera.lWhen the camera lens reflects sunlight or headlight beams.lImage display may be delayed if the temperature around the camera is low.
When Driving
Rear View Monitor
4-139
Mazda6_8DQ8-EA-13L_Edition3 Page263
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L

Black plate (264,1)
qViewing the Display
Guide lines which indicate the width of the vehicle (yellow) are displayed on the screen as
a reference to the approximate width of the vehicle in comparison to the width of the
parking space you are about to back into.
Use this display view for parking your vehicle in a parking space or garage.
b
a
a) Vehicle width guide lines (yellow)
Guide lines serve as a reference to the approximate width of the vehicle.
b) Distance guide lines
These guide lines indicate the approximate distance to a point measured from the
vehicle's rear (from the end of the bumper).
The red and yellow lines indicate the points about 50 cm (19 in) for the red line and 100
cm (39.3 in) for the yellow lines from the rear bumper (at the center point of each of the
lines).
CAUTION
The guide lines on the screen are fixed lines. They are not synced to the driver's
turning of the steering wheel. Always be careful and check the area to the vehicle's
rear and the surrounding area directly with your eyes while backing up.
qRear View Monitor Operation
The operation of the rear view monitor when reversing the vehicle varies depending on the
traffic, road, and vehicle conditions. The amount of steering and the timing also varies
depending on conditions, so confirm the surrounding conditions directly with your eyes
and steer the vehicle in accordance with the conditions.
Be well aware of the above cautions prior to using the rear view monitor.
NOTE
Images displayed on the monitor from the rear view parking camera are reversed images (mirror
images).
1. Shift the shift lever to R to switch the display to the rear view monitor display.
4-140
When Driving
Rear View Monitor
Mazda6_8DQ8-EA-13L_Edition3 Page264
Friday, June 13 2014 6:21 PM
Form No.8DQ8-EA-13L